Campbell CS105 User manual

CS105/CS105M
D
Barometric Pressure Senso
r
Revision: 3/07
Copyright © 1995-2007
Campbell Scientific, Inc.

Warranty and Assistance
The CS105/CS105MD BAROMETRIC PRESSURE SENSOR is warranted
by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and
workmanship under normal use and service for twelve (12) months from date
of shipment unless specified otherwise. Batteries have no warranty.
CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is limited to
repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective
products. The customer shall assume all costs of removing, reinstalling, and
shipping defective products to CAMPBELL SCIENTIFIC, INC. CAMPBELL
SCIENTIFIC, INC. will return such products by surface carrier prepaid. This
warranty shall not apply to any CAMPBELL SCIENTIFIC, INC. products
which have been subjected to modification, misuse, neglect, accidents of
nature, or shipping damage. This warranty is in lieu of all other warranties,
expressed or implied, including warranties of merchantability or fitness for a
particular purpose. CAMPBELL SCIENTIFIC, INC. is not liable for special,
indirect, incidental, or consequential damages.
Products may not be returned without prior authorization. The following
contact information is for US and International customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle
repairs for customers within their territories. Please visit
www.campbellsci.com to determine which Campbell Scientific company
serves your country. To obtain a Returned Materials Authorization (RMA),
contact CAMPBELL SCIENTIFIC, INC., phone [phone]. After an
applications engineer determines the nature of the problem, an RMA number
will be issued. Please write this number clearly on the outside of the shipping
container. CAMPBELL SCIENTIFIC's shipping address is:
CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784
CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

CS105/CS105MD Table of Contents
PDF viewers note: These page numbers refer to the printed version of this document. Use
the Adobe Acrobat® bookmarks tab for links to specific sections.
1. General .........................................................................1
2. Specifications ..............................................................1
3. Installation and Wiring................................................2
4. Programming ...............................................................6
4.1 CS105MD.................................................................................................6
4.2 CS105 .......................................................................................................6
5. Long Lead Lengths......................................................9
6. Correcting Pressure to Sea Level ............................11
7. Maintenance...............................................................11
Appendix
A. Daily Average .......................................................... A-1
Figures
1. CS105 Mounted on the Backplate of an ENC12/14 Enclosure,
and Connected to a CR1000 Datalogger .................................................3
2. CS105MD Mounted on the Backplate of MetData1 Enclosure..................3
3. CS105 Wiring Diagram..............................................................................4
4. CS105MD Wiring Diagram........................................................................5
Tables
1. Signal and Ground Connectors for CS105 .................................................4
2. Conversion Factors for Alternative Pressure Units ....................................6
i

This is a blank page.

CS105/CS105MD Barometric Pressure
Sensor
1. General
The CS105 analog barometer uses Vaisala’s Barocap®silicon capacitive
pressure sensor. The Barocap sensor has been designed for accurate and stable
measurement of barometric pressure. The CS105 outputs a linear 0 to 2.5
VDC signal that corresponds to 600 to 1060 mb. It can be operated in a
powerup or continuous mode. In the powerup mode the datalogger switches
12 VDC power to the barometer during the measurement. The datalogger then
powers down the barometer between measurements to conserve power.
2. Specifications
Operating Range
Pressure: 600 mb to 1060 mb
Temperature: -40°C to +60°C
Humidity: non-condensing
Accuracy
Total Accuracy*** ±0.5 mb @ +20°C
±2 mb @ 0°C to +40°C
±4 mb @ -20°C to +45°C
±6 mb @ -40°C to +60°C
Linearity*: ±0.45 mb @ 20°C
Hysteresis*: ±0.05 mb @ 20°C
Repeatability*: ±0.05 mb @ 20°C
Calibration uncertainty**: ±0.15 mb @ 20°C
Long-Term Stability: ±0.1 mb per year
* Defined as ±2 standard deviation limits of end-point non-linearity,
hysteresis error, or repeatability error
** Defined as ±2 standard deviation limits of inaccuracy of the working
standard at 1000 mb in comparison to international standards (NIST)
*** Defined as the root sum of the squares (RSS) of end-point non-linearity,
hysteresis error, repeatability error and calibration uncertainty at room
temperature
General
Dimensions: 9.7 cm x 5.9 cm x 2.1 cm (3.8” x 2.3” x 0.8”)
Weight: 110 g (4 oz)
Housing material: anodized aluminum
1

CS105/CS105MD Barometric Pressure Sensor
Supply Voltage: 10 to 30 VDC
Supply Voltage Control: When enabled with an internal jumper, the CS105 is
on continually. When disabled, the CS105 can be turned on/off with 5 VDC/0
VDC.
Supply voltage sensitivity: Less than 0.1 mb
Current Consumption: <4 mA (active); <1 µA (quiescent)
Output Voltage: 0 to 2.5 VDC
Warm Up Time: 1 second
Pressure fitting: barbed fitting for 1/8” I.D. tubing
Overpressure limit: 2000 mb
The black outer jacket of the cable is Santoprene® rubber. This
compound was chosen for its resistance to temperature extremes,
moisture, and UV degradation. However, this jacket will
support combustion in air. It is rated as slow burning when
tested according to U.L. 94 H.B. and will pass FMVSS302.
Local fire codes may preclude its use inside buildings.
NOTE
3. Installation and Wiring
The CS105 can be operated in one of two modes: powerup and continuous.
The mode is selected by a jumper located underneath a black plug on the face
of the barometer. When the jumper is not installed, the CS105 is in powerup
mode and the datalogger turns the CS105 on and off with a control port or
excitation channel; to use the excitation channel the datalogger must be able to
provide an excitation voltage of 5 VDC. When the jumper is installed the
CS105 is powered continuously.
CS105s shipped from Campbell Scientific are configured for
powerup mode (jumper open).
NOTE
CS105MDs shipped from Campbell Scientific are configured for
continuous power mode (jumper closed).
NOTE
Mount the CS105 to the backplate in the same enclosure that the datalogger is
located in (Figures 1 and 2).
On the older (grey jacketed) cable pressure (VOUT) was brown
and signal ground (AGND) was white.
NOTE
2

CS105/CS105MD Barometric Pressure Sensor
FIGURE 1. CS105 Mounted on the Backplate of an ENC12/14 Enclosure,
and Connected to a CR1000 Datalogger
INTERNAL BATTERY
TEMPARARY BATTER
MADE IN USA
BPALK
12V ALKALINE BATTERY PACK
Logan, Utah
VAISALA
EXT.TRIG AGND GND SUPPLY VOUT
PRESSURE TRANSMITTER
MODEL
SERIAL NO
RANGE
OUTPUT
SUPPLY
PTB100A
P4450003
800-1060 hPa
0-5 VDC
10-30 VDC
MADE IN FINLAND
FIGURE 2. CS105MD Mounted on the Backplate of MetData1 Enclosure
3

CS105/CS105MD Barometric Pressure Sensor
VAISALA
EXT. TRIG AGND GND SUPPLY VOUT
PRESSURE TRANSMITTER
MODEL
SERIAL NO
RANGE
OUTPUT
SUPPLY
PTB101B
P4450003
600-1060 hPa
0-2.5 VDC
10-30 VDC
MADE IN FINLAND
See Table 1 Blue - Pressure (VOUT)
See Table 1 Yellow - Signal Ground (AGND)
Continuous 12 VDC Red - 12 VDC (SUPPLY)
See Table 1 Black - Power Ground (GND)
Control Port or Excitation Channel Green - Control (EXT. TRIG)
Ground Clear - Shield (SCREW ON CASE)
FIGURE 3. CS105 Wiring Diagram
TABLE 1. Signal and Ground Connectors for CS105
Single-Ended Measurement Differential Measurement
Blue S.E. Input, S.E. 7 (4H) High Side of Diff Input (4H)
Yellow AG (CR10(X), CR500, CR510)
(Other Dataloggers) Low Side of Diff. Input (4L)
Black (21X, CR7, CR9000(X))
G (Other Dataloggers) (21X, CR7, CR9000(X)) G (Other Dataloggers)
4

CS105/CS105MD Barometric Pressure Sensor
VAISALA
EXT. TRIG AGND GND SUPPLY VOUT
PRESSURE TRANSMITTER
MODEL
SERIAL NO
RANGE
OUTPUT
SUPPLY
PTB101B
P4450003
600-1060 hPa
0-2.5 VDC
10-30 VDC
MADE IN FINLAND
6H Green - Pressure (VOUT)
6L White - Signal Ground (AGND)
12 V Switch Red - 12 VDC (SUPPLY)
GND Black - Power Ground (GND)
FIGURE 4. CS105MD Wiring Diagram
5

CS105/CS105MD Barometric Pressure Sensor
4. Programming
4.1 CS105MD
Programming the MetData1 station for the CS105MD is done through
Campbell Scientific’s Short Cut program. Short Cut includes code in the
.DLD file to correct for elevation.
4.2 CS105
Atmospheric pressure changes little with time. In most weather station
applications measuring pressure once an hour is adequate. In Examples 1 and
2 the datalogger turns on the CS105 one minute before the top of the hour with
a control port. As in the example, the execution interval must be one minute or
less. On the hour the datalogger measures the CS105, records the pressure,
and turns off the CS105.
In Example 3 the CS105 is measured every execution interval. The datalogger
turns the CS105 on and waits one second for the CS105 to warm up, before the
measurement is made.
The execution interval must be long enough to accommodate the one second
delay, to warm up the CS105, and all the other measurement and processing
instructions in the program.
In Example 4, the CS105 is measured every execution interval with a 21X. An
excitation channel is used to turn the CS105 on and off.
A CR10(X), CR500, and CR510 excitation channel
cannot be used to turn the CS105 on and off because
the maximum excitation voltage is 2.5 volts. The
CS105 control requires 5 VDC.
WARNING
In the example programs the pressure is reported in millibars (mb). To report
pressure in different units, multiply (Edlog Instruction 37) the measured
pressure by the appropriate conversion factor (Table 2).
TABLE 2. Conversion
Factors for Alternative
Pressure Units
To Find Multiply by
kPa 0.1
mm of Hg 0.75006
in of Hg 0.02953
PSI 0.0145
6

CS105/CS105MD Barometric Pressure Sensor
Example 1. CR1000 Program for Measuring the CS105 Once Every Hour
'Main Program
BeginProg
Scan(5,Sec,1,0)
'CS105 Barometric Pressure Sensor measurement BP_mmHg:
If IfTime(59,60,Min) Then PortSet(1,1)
If IfTime(0,60,Min) Then
VoltSE(BP_mmHg,1,mV2500,1,1,0,_50Hz,0.184,600.0)
BP_mmHg=BP_mmHg*0.75006
PortSet(1,0)
EndIf
'Call Data Tables and Store Data
NextScan
EndProg
Example 2. CR10(X) Program for Measuring the CS105 Once Every Hour
;{CR10X}
;
*Table 1 Program
01: 30 Execution Interval (seconds)
01: If time is (P92)
1: 59 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 41* Set Port 1* High
02: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 30 Then Do
03: Volts (SE) (P1)
1: 1 Reps
2: 25** ± 2500 mV 60 Hz Rejection Range
3: 7* SE Channel
4: 1* Loc [ P_mb ]
5: .184 Mult
6: 600 Offset
04: Do (P86)
1: 51* Set Port 1* Low
05: End (P95)
06: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)
7

CS105/CS105MD Barometric Pressure Sensor
07: Real Time (P77)
1: 0110 Day,Hour/Minute
08: Sample (P70)
1: 1 Reps
2: 1* Loc [ P_mb ]
-Input Locations-
1 P_mb
* Proper entries will vary with program and datalogger channel, and input location assignments.
** On the 21X use the 5000 mV slow range.
Example 3. CR10(X) Program for Measuring the CS105 Every Execution Interval
;{CR10X}
;
*Table 1 Program
01: 2 Execution Interval (seconds)
01: Do (P86)
1: 41* Set Port 1* High
02: Excitation with Delay (P22)
1: 1 Ex Channel
2: 0 Delay W/Ex (units = 0.01 sec)
3: 100 Delay After Ex (units = 0.01 sec)
4: 0 mV Excitation
03: Volts (SE) (P1)
1: 1 Reps
2: 25** ± 2500 mV 60 Hz Rejection Range
3: 7* SE Channel
4: 1* Loc [ P_mb ]
5: .184 Mult
6: 600 Offset
04: Do (P86)
1: 51* Set Port 1* Low
05: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 30 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)
06: Real Time (P77)
1: 0110 Day,Hour/Minute
07: Average (P71)
1: 1 Reps
2: 1* Loc [ P_mb ]
8

CS105/CS105MD Barometric Pressure Sensor
-Input Locations-
1 P_mb
* Proper entries will vary with program and datalogger channel, and input location assignments.
** On the 21X use the 5000 mV slow range.
Example 4. 21X Program for Measuring the CS105 Every Execution Interval Using an
Excitation Channel to Turn the CS105 On and Off.
;{21X}
;
*Table 1 Program
01: 2 Execution Interval (seconds)
01: Excite Delay Volt (SE) (P4)
1: 1 Reps
2: 5 SE Channel
4: 1* Excite all reps w/Exchan 1
5: 100 Delay (units 0.01 sec)
6: 5000 mV Excitation
7: 1* Loc [ P_mb ]
8: .184 Mult
9: 600 Offset
02: If time is (P92)
1: 0 Minutes into a
2: 30 Minute Interval
3: 10 Set Output Flag High
03: Real Time (P77)
1: 0110 Day,Hour/Minute
04: Average (P71)
1: 1 Reps
2: 1* Loc [ P_mb ]
-Input Locations-
1 P_mb
* Proper entries will vary with program and datalogger channel, and input location assignments.
5. Long Lead Lengths
There is a 0.06 mV/foot voltage drop in the CS105 signal leads. This voltage
drop, in long lead lengths, will raise the barometric reading by approximately
1.1 mb per 100 feet.
For lead lengths greater than 20 feet, use the differential instruction
(Instruction 2) to measure the CS105.
9

CS105/CS105MD Barometric Pressure Sensor
Example 5. CR10(X) Program for Measuring the CS105 Once Every Hour with Instruction 2
(Differential Measurement)
;{CR10X}
;
*Table 1 Program
01: 10 Execution Interval (seconds)
01: If time is (P92)
1: 59 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 41* Set Port 1* High
02: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 30 Then Do
03: Volt (Diff) (P2)
1: 1 Reps
2: 25* ± 2500 mV 60 Hz Rejection Range
3: 4* DIFF Channel
4: 1* Loc [ P_mb ]
5: .184 Mult
6: 600 Offset
04: Do (P86)
1: 51* Set Port 1* Low
05: End (P95)
06: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 60 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)
07: Real Time (P77)
1: 0110 Day,Hour/Minute
08: Sample (P70)
1: 1 Reps
2: 1* Loc [ P_mb ]
-Input Locations-
1 P_mb
* Proper entries will vary with program and datalogger channel, and input location assignments.
** On the 21X use the 5000 mV slow range.
10

CS105/CS105MD Barometric Pressure Sensor
6. Correcting Pressure to Sea Level
The weather service, most airports, radio stations, and television stations
reduce the atmospheric pressure to a common reference (sea level). Equation 1
can be used to find the difference in pressure between the sea level and the site.
That value (dP) is then added to the offset (600 mb) in the measurement
instruction. U. S. Standard Atmosphere and dry air were assumed when
Equation 1 was derived (Wallace, J. M. and P. V. Hobbes, 1977: Atmospheric
Science: An Introductory Survey, Academic Press, pp. 59-61).
dP E =−−
⎛
⎝
⎜⎞
⎠
⎟
⎧
⎨
⎪
⎩
⎪
⎫
⎬
⎪
⎭
⎪
1013 25 1 1 44307 69231
5.25328
..(1)
The value dP is in millibars and the site elevation, E, is in meters. Add dP to
the offset in the measurement instruction.
Use Equation (2) to convert from feet to meters.
Em Eft
ft m
() ()
.
=3 281 (2)
Sea level correction is automatically coded into datalogger programs when
using Short Cut.
7. Maintenance
There are no user-serviceable parts on CS105. Vaisala recommends
recalibrating the CS105 every year. Contact Campbell Scientific, Inc., phone
[phone], for an RMA number before returning the sensor for
recalibration.
11

CS105/CS105MD Barometric Pressure Sensor
This is a blank page.
12

Appendix A. Daily Average
If the CS105 will be measured every minute or faster, and a daily average is
required, follow Example 5. In Example 5 the daily average, maximum, and
minimum pressure is recorded at midnight. A constant is subtracted from the
pressure before the average instruction is executed. This prevents the loss of
significant digits when adding small numbers to large numbers in floating
point arithmetic.
Example 5. Recording a Daily Average, Maximum, and Minimum Pressure
;{CR10X}
;
*Table 1 Program
01: 5 Execution Interval (seconds)
01: Do (P86)
1: 41* Set Port 1* High
02: Excitation with Delay (P22)
1: 1 Ex Channel
2: 0 Delay W/Ex (units = 0.01 sec)
3: 100 Delay After Ex (units = 0.01 sec)
4: 0 mV Excitation
03: Volts (SE) (P1)
1: 1 Reps
2: 25** ± 2500 mV 60 Hz Rejection Range
3: 1* SE Channel
4: 1* Loc [ P_mb ]
5: .184 Mult
6: 600 Offset
04: Do (P86)
1: 51* Set Port 1 Low*
05: Z=X+F (P34)
1: 1* X Loc [ P_mb ]
2: -800 F
3: 2* Z Loc [ P_const ]
06: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 1440 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)
07: Set Active Storage Area (P80)
1: 3 Input Storage Area
2: 3* Loc [ P_mb_avg ]
A-1

Appendix A. Daily Average
08: Average (P71)
1: 1 Reps
2: 2* Loc [ P_const ]
09: If Flag/Port (P91)
1: 10 Do if Output Flag is High (Flag 0)
2: 30 Then Do
10: Z=X+F (P34)
1: 3* X Loc [ P_mb_avg ]
2: 800 F
3: 3* Z Loc [ P_mb_avg ]
11: End (P95)
12: If time is (P92)
1: 0 Minutes (Seconds --) into a
2: 1440 Interval (same units as above)
3: 10 Set Output Flag High (Flag 0)
13: Set Active Storage Area (P80)
1: 1 Final Storage Area 1
2: 10 Array ID
14: Real Time (P77)
1: 0110 Day,Hour/Minute
15: Sample (P70)
1: 1 Reps
2: 3* Loc [ P_mb_avg ]
16: Maximize (P73)
1: 1 Reps
2: 10 Value with Hr-Min
3: 1* Loc [ P_mb ]
17: Minimize (P74)
1: 1 Reps
2: 10 Value with Hr-Min
3: 1* Loc [ P_mb ]
-Input Locations-
1 P_mb
2 P_const
3 P_mb_avg
* Proper entries will vary with program and datalogger channel, and input location assignments.
** With a 21X, use the 5000 mV measurement range.
A-2

This is a blank page.

Campbell Scientific Companies
Campbell Scientific, Inc. (CSI)
815 West 1800 North
Logan, Utah 84321
UNITED STATES
www.campbellsci.com
[email protected]
Campbell Scientific Africa Pty. Ltd. (CSAf)
PO Box 2450
Somerset West 7129
SOUTH AFRICA
www.csafrica.co.za
[email protected]
Campbell Scientific Australia Pty. Ltd. (CSA)
PO Box 444
Thuringowa Central
QLD 4812 AUSTRALIA
www.campbellsci.com.au
[email protected].au
Campbell Scientific do Brazil Ltda. (CSB)
Rua Luisa Crapsi Orsi, 15 Butantã
CEP: 005543-000 São Paulo SP BRAZIL
www.campbellsci.com.br
[email protected]
Campbell Scientific Canada Corp. (CSC)
11564 - 149th Street NW
Edmonton, Alberta T5M 1W7
CANADA
www.campbellsci.ca
[email protected]
Campbell Scientific Ltd. (CSL)
Campbell Park
80 Hathern Road
Shepshed, Loughborough LE12 9GX
UNITED KINGDOM
www.campbellsci.co.uk
[email protected]
Campbell Scientific Ltd. (France)
Miniparc du Verger - Bat. H
1, rue de Terre Neuve - Les Ulis
91967 COURTABOEUF CEDEX
FRANCE
www.campbellsci.fr
[email protected]
Campbell Scientific Spain, S. L.
Psg. Font 14, local 8
08013 Barcelona
SPAIN
www.campbellsci.es
[email protected]
Please visit www.campbellsci.com to obtain contact information for your local US or International representative.