Camtree Hunt CH-MPC-SRP User manual

Multipurpose Cage Shoulder Mount
Rig
(CH-MPC-SRP)
INSTRUCTION MANUAL
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permied by
the applicable copyright statutes or in wring by the Publisher.
CAMTREE HUNT

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 2
INTRODUCTION
A culminaon of art and engineering, designed from the ground up, Using best materials, trendy
design with electrifying performance. Sophiscatedly balanced and adjustable system with a myr-
iad of unending mounng opons gives maximum stability and comfort that a cameraman actu-
ally desires. Once it’s on your shoulders, its completely balanced, you don’t need to e your
hands on it.. High, low and mid-level shoong angles are a breeze with just the twist of a couple
of thumbscrews, giving you important on-the-go opons to expand your cinemac creavity.
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below.
Top Handle Top Plate Side Brackets
A-Box
Base Plate
2x 300mm Female thread Rods
Counter Weight with Bracket 19mm/15mm Bracket
Quick Back Baery Plate
Shoulder Pad
Handle Set
Flip Follow FocusRod Adapter Gear belt Speed crank
Rosee handle set
4x150mm Female Rods

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 3
 Mount the base plate with tripod mounng plate and ghten it with help of screw driver.
 Now mount the camera set up onto the tripod and ghten the knob to secure.
ASSEMBLING YOUR HUNT CAMERA CAGE WITH HANDLE & BASEPLATE
 Mount the camera on base plate and secure it by ghtening provided screws with help of
screw driver.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 4
 Aach side brackets of cage on both sides of Base plate with provided allen bolts & ghten
with allen key.
 Slide in the top handle on adapter aached to top plate and ghten the knob to ensure slip
free connecon.
 Now loosen the allen bolts from top plate of cage & aach it to side brackets with allen bolts
& ghten with allen key to secure it properly.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 5
 Now remove the cap from lens mount of the camera in order to aach the lens.
 Aach the 15mm rod adapter with the rear of Base Plate and ghten it with allen key.
 Then insert 15mm rods into rod adapter and ghten the knob to secure.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 6
 Now screw in four provided screws to the baery mount of the camera in order to aach
quick back baery plate.
 Aach the quick back baery plate to camera & then connect the 4-pin Lemo connector to
camera and aach V-mount baery to baery plate.
 Mount the A-Box on 15mm Rod and ghten the knob to secure. Connect the jack connector
of A-Box to camera.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 7
 Now mount the exible shoulder mount at the end of rods and ghten the knob to secure.
Then, loosen the knobs of shoulder mount to adjust the length, then ghten all the knobs to
secure.
 Now insert 15mm rods into rod adapter aached on shoulder mount and ghten the knobs
to secure. Then aach counter weight with bracket to rods and secure it properly.
 Insert 15mm rods into front rod adapter of base plate and ghten the knobs to secure.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 8
 Aach exible gear belt on your camera’s outer focusing ring diameter and secure the gear
belt using the provided screw.
 Now mount the solid gear follow focus on 15mm rods, align it with gear ring and ghten the
side knob to secure.
ASSEMBLING YOUR CAMTREE-MB-20 SWING AWAY WIDE ANGLE MATTE BOX
 Insert the french ag into the (big) slots provided in the hinges. Using the same approach, in-
sert the side ags into the mae box and ghten the screws.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 9
 Aach knicker on conversion ring, then aach the ring with conversion ring holder and
ghten the knot.
 You can easily insert the lter holders as
shown in the image.
Note: The lter holder supports the use of 4x4” square lters, kit includes 2pcs of lter holders;
one is rotang 180° and another is non-rotang.
Note: Pulling the knob upwards releases the
MB-20 CF Mae Box allowing it to easily
swing away from the camera.

Camtree Hunt Mulpurpose Cage Shoulder Mount Rig 10
 Insert MB-20 CF mae box to rails and secure with provided knob. Aach knicker to camera
lens barrel properly and ghten the knot.
 Aach the handle set to 15mm front rails and secure the handles by pressing the locks.
 Loosen the knobs to adjust the angle of handles. Aer seng the handles in required posi-
on, ghten all the knobs to secure.