Camtree G-51 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Gripper Campod Sucon Car Mount (G-51)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Assembly Manua l
3 x Gripper Sucon Cups 6 x 6” Extension
Rods
6 x Ball Tilt Heads
2 x Ratchet/Safety
Wires 3 x Shanks
For Gripper
Cups
2 x C-hooks
2 x Round
Hooks
Camera Mount
Hub
3 x 3’’ Extension
Rods
Complimentary Dust
Cover

2
NOTE: While ng your G-51 and choosing which holes to use in the hub, keep in mind the relaonship
between the surface you are using to mount G-51 and the posion of camera. This will help you to
choose correct hub holes.
Gripper Setup
 Take Camera Mount Hub, screw either 3” or
6” extension rod into one of the central
holes. Repeat this process with other two
rods to build your tripod.
 Now insert Ball Tilt Head into the rod and
ghten to secure properly. Then screw-in
another length of rod into ball lt head.
Adjust the distance of tripod legs by adding
dierent length of extension rods, as
required, to reach mounng surface.
 To guarantee proper adhesion of sucon cups, check that the surfaces of both, sucon cup and
mounng surface are clean & dry. Please mount the device on smooth, even and non-porous surfaces.
 Remove the complimentary dust cover and
place your rst sucon cup on the selected
posion from where you want to shoot. Lock
the sucon cup with lever on it. Repeat this
process for all sucon cups.
NOTE: Make sure to ghten all connecons to avoid accidental loss of camera and rig.
 Add the second set of Ball Tilt Heads to
sucon cups and ghten to properly secure
them.

3
 Now aach the rod system into ball lt head
and ghten to secure it properly.
 Then aach any leveling base of your choice
(Not Included) to the camera Mount Hub and
secure it carefully by ghtening the knob
using allen key, if required.
 Aach both the round hooks with camera
hub and insert one end of both safety wires
into each hook.
NOTE: Although G-51 Gripper’s holding force is adequate for regular driving shots, safety wires must be
used for addional security. When mounted on cars, the objects aached to the Gripper (e.g. camera,
etc.) have to be secured addionally and also to avoid vibraons, especially on thin metal sheets.
 Now aach both the C-Hooks with your
clamping surface and insert the other end of
both safety wires into each C-Hook.
 Finally, using any of the 1/4”-20 or 3/8’’-16
screws located in the centre of camera hub,
aach your professional camera to the
gripper.
NOTE: The design and construcon of this rig supports cameras up to 10kg/ 22lb (at running posion)
& 20kg/ 44lb (at stac posion), and is meant for use when traveling at a maximum speed of 40 km/hr.
Do not exceed these specicaons.

4
YOUR CAMTREE GRIPPER CAMPOD SUCTION CAR MOUNT
ALL DRESSED-UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.