Canon PIXMA MG6120 Series Manual

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MG6120
Mac OS
1

<< Previous Next >>
Installing Your Multifunction
to Your Network for the First Time
PIXMA MG6120
Mac OS
2
Preparing to Connect My Multifunction To My Network
3
Connecting Your MG6120 To Your Network
5
Installing The MG6120 Software
12

Preparing to Connect My Multifunction
To My Network
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
3
<< Previous Next >>

Preparing to Connect My Multifunction
To My Network
4
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of
the network device vary depending on your system environment. For details,
refer to your device's instruction manual or contact its manufacturer.
•In an office setup, consult your network administrator
•If you connect to a network that is not protected with security measures,
there is a risk of disclosing data such as your personal information to a third
party.
•If an error message appears or if you have trouble with the network
connection, refer to the printed manual: Network Setup Troubleshooting.
•Place the machine and computer on the same network segment.
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.
Be sure to prepare an access point.
<< Previous Next >>

Connecting Your MG6120 To Your Network
5
Step 1
Use the ↑ or ↓ button (A) to display
Setup, then touch the right
FUNCTION button (B).
Step 2
Use the ← or → button (C) to select
Wireless LAN setup, then touch the
OK button.
<< Previous Next >>

Connecting Your MG6120 To Your Network
6
Step 3
Select Yes, then touch the OK button.
Step 4
Select Easy setup, then touch the OK
button.
When wireless connection is
enabled, the Wi-Fi lamp lights blue.
<< Previous Next >>

Connecting Your MG6120 To Your Network
7
Step 5
Select the access point name you
wrote down, then touch the OK
button.
Step 6
Make sure that one of the below
screens is displayed, then touch the
right FUNCTION button.
Note:
•Nearby access points may be detected.
•Access point names with 2-byte characters are not
displayed properly, however, they can be selected.
If neither is displayed, go to Step 9.
<< Previous Next >>

Connecting Your MG6120 To Your Network
8
Step 7
Enter the network key you wrote down on, then touch the left FUNCTION button (E).
1. Touch the center FUNCTION button (F) to switch
character entry modes.
2. Enter upper and lower case letters of the alphabet
correctly.
<< Previous Next >>

Connecting Your MG6120 To Your Network
9
Step 7 (continued) Character Entry
This machine allows you to enter characters when an on-screen keyboard is displayed.
Follow the procedure below.
1. When the on-screen keyboard
shown above is displayed,
touch the center FUNCTION
button (A) to switch to a
keyboard having the
characters you want to use.
Four character sets are available: Upper-case alphabets, lower-case alphabets, numbers, and
symbols. Each time you touch the center FUNCTION button, the on-screen keyboard is
switched among them.
<< Previous Next >>

Connecting Your MG6120 To Your Network
10
Step 7 (continued) Character Entry
2. Select a character on the on-
screen keyboard using the
↑↓←→ buttons (B) then
touch the OK button to enter
it. Entered characters are
displayed on the upper
section (C) of the on-screen
keyboard.
3. Repeat (1) and (2) to enter
more characters.
4. After you enter all characters
you need, touch the left
FUNCTION button (D).
•To insert a space, select Space on the on-screen keyboard and touch the
OK button.
•To insert characters, select the section (C) of the screen using the ↑ or ↓
button, move the cursor to the character on the right of the target position
using the ← or → button, then enter characters.
•To delete a character, select the section (C) of the screen using the ↑ or ↓
button, move the cursor to the character on the right of the target position
using the ← or → button , then touch the right FUNCTION button (E).
<< Previous Next >>