Canon MultiPASS C530 User manual

CallOfl
COLOR BUBBLE JETTM PRINTER MULTIPASS TM
FAX•SCANNER •COPIER C530/C560
User's Manual

< iiil;i]iZ; ii iiiii ,iii!i!i!iii!iiiiii!i!!!iiiiili!ii!iiiii!i!ii i¸
This manual is copyrighted by Canon Computer Systems, Inc. (CCSI) with all rights reserved.
Under the copyright laws, this manual may not be reproduced in any form, in whole or part,
without prior written consent of CCSI.
©1999 Canon Computer Systems, Inc.
Canon Computer Systems, Inc. has reviewed this manual thoroughly in order to make it an
easy to use guide for your Canon MultiPASS system. All statements, technical information, and
recommendations in this guide and in any guides or related documents are believed reliable, but
the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended
to be, nor should they be understood to be, representations or warranties concerning the products
described.
Your MultiPASS and the software media included with your system have been sold to you
subject to the limited warranties set forth in the warranty and license agreement enclosed with the
respective products. All software is licensed AS IS, as described in the license agreement enclosed
with the software media. Further, CCSI reserves the right to make changes in the specifications of
the products described in this guide at any time without notice and without obligation to notify
any person of such changes.
Preface ii

Canon, BCI, BJ,Bubble Jet, MultiPASS, ScanGear, and UHQ are trademarks and SelectExchange is
a service mark of Canon Inc.
All other product and brand names are trademarks or service marks of their respective owners.
ENERGYSTAR®COMPLIANT
As an ENERGYSTAR® Partner, Canon U.S.A., Inc. has determined that this product meets the
ENERGYSTAR® guidelines for energy efficiency.
Preface iii

PRE-INSTALLATION REQUIREMENTS FOR CANON FACSIMILE EQUIPMENT
A°
B°
Location
Supply a suitable table, cabinet, or desk. See Appendix A for the unit's dimensions and weight.
Appendix A, Specifications
Order Information
1. Only a single line, touch-tone or rotary telephone set is to be used.
2. Order an RJ11-C modular jack (USOC code), which should be installed
by the phone company. If the RJ11-C jack is not present, installation
cannot occur.
3. Order a normal business line from your telephone company's business representative. The
line should be a regular voice grade line or the equivalent. Use one line per unit.
DDD (DIRECT DISTANCE DIAL) LINE
-or-
IDDD INTERNATIONAL DIRECT DISTANCE DIAL) LINE IF YOU COMMUNICATE
OVERSEAS
Preface iv

Canon recommends an individual line following industry standards, e.g. the 2500 (Touch Tone)
or 500 (Rotary/Pulse Dial) telephones. A dedicated extension off a PBX unit without "Call
Waiting" can be used with your MultiPASS. Key telephone systems are not recommended because
they send non-standard signals to individual telephones for ringing and special codes, which may
cause a fax error.
C° Power Requirements
This equipment should be connected to a standard 120 volt AC, three-wire grounded outlet
only. Do not connect this unit to an outlet or power line shared with other appliances that
cause "electrical noise". Mr conditioners, electric typewriters, copiers, and machines of this
sort generate electrical noise which often interferes with communications equipment and the
sending and receiving of documents.
CONNECTION OF THE EQUIPMENT
This equipment complies with Part 68 of the FCC rules. On the rear panel of this equipment is a
label that contains, among other information, the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. If requested, this information must be given to
the telephone company. This equipment may not be used on coin service provided by the
telephone company. Connection to party lines is subject to state tariffs.
Prcfacc V

An FCC compliant telephone cord and modular jack is provided with this equipment. This
equipment is designed to be connected to the telephone network or premises wiring using a
compatible modular jack which is Part 68 compliant. See Installation instructions for details.
The REN is used to determine the quantity of devices which may be connected to the telephone
line. Excessive RENs on the telephone line may result in the devices not ringing in response to an
incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to the line, as determined by the total
RENs, contact the telephone company to determine the maximum REN for the calling area.
IN CASE OF EQUIPMENT MALFUNCTION
Should any malfunction occur which cannot be corrected by the procedures described in this
User'sManual, disconnect the equipment from the telephone line or unplug the power cord. The
telephone line should not be reconnected or the power cord plugged in until the problem is
completely resolved. Users should contact Canon Authorized Service Facilities for servicing of
equipment. Information regarding Authorized Service Facility locations can be obtained by calling
the Canon Computer Systems Customer Care Center. (See page 1=14for details.)
Preface vi

RIGHTS OF THE TELEPHONE COMPANY
Should the equipment cause harm to the telephone network, the telephone company may
temporarily disconnect service. The telephone company also retains the right to make changes in
facilities and services which may affect the operation of this equipment. When such changes are
necessary, the telephone company is required to give adequate prior notice to the user.
WARNING
Do not make any changes or modifications to the equipment unless otherwise specified in this
manual. If such changes or modifications should be made, you could be required to stop
operation of the equipment.
MultiPASS C530: Facsimile Transceiver, Model H12159
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept an interference received, including interference that may cause
undesired operation.
Preface vii

This equipment has been tested and found to comply with the limits for a class Bdigital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC
Rules. Do not make any changes or modifications to the equipment unless otherwise specified in
this manual. If such changes or modifications should be made, you could be required to stop
operation of the equipment.
Preface viii

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a
computer or other electronic device to send any message via a telephone fax machine unless such
message clearly contains in a margin at the top or bottom of each transmitted page or on the first
page of the transmission, the date and time it is sent and an identification of the business or other
entity, or other individual sending the message and the telephone number of the sending machine
or such business, other entity, or individual.
To automatically enter this information into your MultiPASS, follow the instructions in your
Quick Start Guide.
Preface ix

PRE-INSTALLATION REQUIREMENTS FOR CANON FACSIMILE EQUIPMENT
A. Location
Supply a suitable table, cabinet, or desk. See Appendix A for the unit's dimensions and weight.
Appendix A, Specifications
B. Order Information
1. Provide only a single-line to touch-tone or rotary telephone set terminated with a standard
4-pin modular phone plug. (Touch-tone is recommended if available in your area.)
2. Order an RJ11-C modular jack (USOC code), which should be installed by the phone
company. If the RJ11-C jack is not present, installation cannot occur.
3. Order a normal business line from your telephone company's business representative. The
line should be a regular voice grade line or equivalent. Use one line per unit.
DDD (DIRECT DISTANCE DIAL) LINE
-or-
IDDD INTERNATIONAL DIRECT DISTANCE DIAL) LINE IF YOU COMMUNICATE
OVERSEAS
P_'efa ce X