Canon L360 User manual

CANON
FAX – L360
SIMPLIFIED
GUIDE

2
CONTENTS
PAGE
FAX-L360
I To Register Sender’s Identification 3
II Sending Documents 4
III Setting Up Speed Dialing
A One-touch Speed Dial 5
B Coded Speed Dial 6
C Group Dial 7
IV To Erase Auto-Dialing Numbers
A One-touch Speed Dial 8
B Coded Speed Dial 8
C Group Dial 8
V Sending To More Than One Location 9
(Sequential Broadcasting)
VI Sending At A Preset Time 10
(Delayed Transmission)
VII To Print Documents Received In The Memory 11
VIII To Re-send Documents Received In Memory 12
To A Different Destination
(If No. VII method above is not possible)
IX To Print Reports & Lists
A Speed Dial Lists 13
B Activity Management Report 13
C Document Memory List 13
X To Make A Photocopy 14
XI Setting Up Transmission (TX) Report
For Every Document Sent Out 15
XII Erasing A Document That Is Queuing To Be Sent
FromTheMemory 16

3
TO REGISTER SENDER IDENTIFICATION
I. INPUT YOUR FAX NUMBER AND COMPANY NAME
1. Open One-Touch Speed Dial panel
2. Press Data Registration
3. Press Set to display “1. USER SETTINGS”
4. Press Set to display “1. DATE & TIME”
5. Press ∨
∨∨
∨to display “2. UNIT TELEPHONE #”
6. Press Set
7. Enter your fax number
8. Press Set to display “3. UNIT NAME”
9. Press Set
10. Enter your company or personal name
Register the name by pressing the buttons on the numeric keypad
CODE NUMBERS FOR ALPHABETS AND SYMBOLS
NUMERIC KEY ALPHABETS NUMERIC KEY ALPHABETS
2 A,B,C 6 M,N,O
3 D,E,F 7 P,Q,R,S
4 G,H,I 8 T,U,V
5 J,K,L 9 W,X,Y,Z
#symbols
Press >
>>
>to enter next alphabet
Press SPACE to enter a space
Press * to enter a digit
11. Press Set to save the name
12. To end, press Stop 



4
II SENDING A DOCUMENT
A. DIRECT / MANUAL SENDING
1. Place documents face down on the feeder
2. Press Hook 


3. Enter fax number
4. Press Start/Copy 


N.B. The fax number dialed will not appear in the TX and activity report
in the above method.
B. MEMORY SENDING
1. Place documents face down on the feeder
2. Enter fax number
4. Press Start/Copy 


5. Take note of “ TX / RX ” number
C. ONE-TOUCH / CODED DIAL SENDING
1. Place documents face down on the feeder
2. Press the appropriate one-touch key OR
Press CODED DIAL and a two-digit code
3. Take note of “ TX / RX ” number
N.B. If direct sending is required, activate HOOK sign before step No. 2
TO STOP SENDING
A. During a DIRECT TX sending, press Stop 


B./C. During a memory sending, press Stop 

then *to confirm the stop
sending function.

5
III TO STORE FAX NUMBERS
A. ONE-TOUCH SPEED DIAL ( 01-KEY TO 32-KEY )
1. Open One-Touch Speed Dial panel
2. Press Data Registration
3. Press ∨
∨∨
∨to display “2. TEL REGISTRATION”
4. Press Set twice
5. Press ∨
∨∨
∨(if necessary) until an empty space appears
6. Press Set twice
7. Enter fax number
8. Press Set twice
9. Enter name
Register the name by pressing the buttons on the numeric keypad
CODE NUMBERS FOR ALPHABETS AND SYMBOLS
NUMERIC KEY ALPHABETS NUMERIC KEY ALPHABETS
2 A,B,C 6 M,N,O
3 D,E,F 7 P,Q,R,S
4 G,H,I 8 T,U,V
5 J,K,L 9 W,X,Y,Z
#symbols
Press >
>>
>to enter next alphabet
Press SPACE to enter a space
Press * to enter a digit
10. Press Set
11. To continue, press Data Registration
12. Repeat steps No. 5 to No. 10
13. To end, press Stop 



6
B. CODED SPEED DIAL (*00 TO *99 )
1. Open One-Touch Speed Dial panel
2. Press Data Registration
3. Press ∨
∨∨
∨to display “2. TEL REGISTRATION”
4. Press Set
5. Press ∨
∨∨
∨to display “2. CODED SPD DIAL”
6. Press Set
7. Press ∨
∨∨
∨(if necessary) until an empty space appears
8. Press Set twice
9. Enter fax number
10. Press Set twice
11. Enter name (refer to A.9. on III : TO STORE FAX NUMBERS)
12. Press Set
13. To continue, press Data Registration
14. Repeat steps No. 7 to No. 12
15. To end, press Stop 



7
C. TO PROGRAM GROUP DIAL
1. Open One-Touch Speed Dial panel
2. Press Data Registration
3. Press ∨
∨∨
∨to display “2. TEL REGISTRATION”
4. Press Set
5. Press ∨
∨∨
∨to display “3. GROUP DIAL”
6. Press Set
7. Press ∨
∨∨
∨(if necessary) until an empty space appears
8. Press Set twice
9. Close panel cover & press desired one-touch keys
& / or the coded speed dial numbers
10. Press Set twice
11. Enter name for the above group dialer (refer to A.9. on III : TO
STORE FAX NUMBERS)
12. Press Set
13. To continue, press Data Registration
14. Repeat steps No. 7 to No. 12
15. To end, press Stop 



8
IV TO ERASE A SPEED DIAL
A TO CANCEL A NUMBER IN THE ONE-TOUCH SPEED DIAL
1. Follow steps A.1. to A.4. (Refer to III : TO STORE FAX NUMBERS :
ONE-TOUCH SPEED DIAL)
2. Close panel cover & press desired one-touch key
3. Press
Set twice
4. Press
Clear
5. Press
Set
6. Press
Stop 


B TO CANCEL A NUMBER IN THE CODED SPEED DIAL
1. Follow steps B.1. to B.6. (Refer to III : TO STORE FAX NUMBERS :
CODED SPEED DIAL)
2. Press
CODED DIAL followed by the relevant two-digit code
3. Press
Set twice
4. Press
Clear
5. Press
Set
6. Press
Stop 


C TO CANCEL A GROUP DIALER
1. Follow steps C.1. to C.6. (Refer to III : TO STORE FAX NUMBERS
: GROUP DIAL)
2. Close panel cover & press the desired group dialer using one-touch key OR
CODED DIAL & the relevant two-digit code
3. Press
Set twice
4. Press
Clear for each of the speed dialers that are to be deleted
5. To confirm, press Set
6. Press
Set again if the name of the group dialer remains unchanged
7. Press
Stop 



9
V SENDING TO MORE THAN ONE LOCATION
(SEQUENTIAL BROADCASTING)
A. USING ONE-TOUCH / CODED SPEED DIAL
1. Place documents face down on the feeder
2. Press all the relevant one-touch / coded-dial numbers one right after
another
3. If there is one more destination to be dialed manually, enter the number
using the numeric 10-key pad
4. Press Start/Copy 


5. Take note of “ TX / RX ” number
N.B. Please check on the MULTI TRANSACTION REPORT which
will be generated out after the broadcast is completed to ensure that
the broadcast is successful.

10
VI TO SEND DOCUMENTS AT A LATER TIME
(DELAYED TRANSMISSION)
1. Open One-Touch Speed Dial panel
2. Press Delayed Transmission
3. Press Set
4. Enter the desired time (time set must be within 24 hours from the
time on the display)
5. Press Set
6. Enter the fax number
7. Press Start/Copy 


8. Place documents face down on the machine
9. Take note of “ TX / RX ” number
Machine will now scan documents into the memory.

11
VII WHEN THE FAX DISPLAYS “RECEIVED IN MEMORY”
Display screen flashes message “RECEIVED IN MEMORY” repeatedly
and keeps prompting the following :
“LOAD PAPER”
Action : Refill paper supply
OR
“REPLACE CARTRIDGE”
Action : Put in a new toner cartridge
OR
“REC. PAPER JAM”
Action : Remove jammed paper carefully in a whole piece
Machine will start to print the received documents from the memory.

12
VIII RE-SENDING
IF No.VII ABOVE METHOD IS NOT POSSIBLE, EACH
DOCUMENT RECEIVED IN THE MEMORY CAN BE RE-SENT
INDIVIDUALLY TO ANOTHER DESTINATION FOR PRINTING
1. Open One-Touch Speed Dial panel
2. Press Memory Reference
3. Press ∨
∨∨
∨to display “3. RESEND DOCUMENT”
4. Press Set
5. Press ∨
∨∨
∨if necessary to select a new “TX/RX No.”
(must be greater than 5000)
6. Press Set to display “SELECT LOCATIONS”
7. Dial the fax number
8. Press Set twice
Machine will now start to send the document.

13
IX TO PRINT REPORTS AND LISTINGS
A. SPEED DIAL LIST
1. Open One-Touch Speed Dial panel
2. Press Report
3. Press ∨
∨∨
∨to display “2. SPEED DIAL LIST”
4. Press Set
5. Press ∨
∨∨
∨to search for desired list
i.e. “1. 1-TOUCH LIST”, “2. CODED DIAL LIST” or
“3.GROUP DIAL LIST”
6. Press Set twice
B. TO PRINT A LIST OF PREVIOUS 20 TRANSACTIONS
1. Open One-Touch Speed Dial panel
2. Press Report
3. Press Set
C. TO PRINT DOCUMENT MEMORY LIST
To check the list of documents currently stored in the memory
1. Open One-Touch Speed Dial panel
2. Press Report
3. Press ∨
∨∨
∨to select “4.DOC MEMORY LIST”
4. Press Set

14
X MAKING COPIES
1. Place documents face down on the feeder
2. Press Start/Copy 


3. Enter the number of copies required
4. Press Start/Copy 

again to start copying
To cancel the printing, press Stop 



15
XI TRANSMISSION REPORT
To set up Transmission (TX) Report For Every Document Sent Out
1. Open One-Touch Speed Dial panel
2. Press Data Registration
3. Press Set
4. Press ∨
∨∨
∨to display “2.REPORT SETTINGS”
5. Press Set twice
6. Press ∨
∨∨
∨to select “OUTPUT YES”
7. Press Set

16
XII ERASING A TRANSMIT DOCUMENT FROM THE MEMORY
1. Press Memory Reference
2. Press ∨
∨∨
∨to select “4.DELETE DOCUMENT”
3. Press Set
4. Press ∨
∨∨
∨to display the desired TX/RX number
5. Press Set
6. Press *to confirm deletion
7. Press Stop 

