Canon IX-R7000 User manual

1IX-R7000 Card Lamination Module Configuration Guide
IX-R7000 Card Lamination
Module
Configuration Guide
Last updated: 4/20/2023

2IX-R7000 Card Lamination Module Configuration Guide
Table of Contents
Preface ................................................................................................................................................ 3
How to Use This Guide.................................................................................................................... 3
Chapter 1 Overview and Setup ........................................................................................................... 4
Firmware Requirements.................................................................................................................. 4
Installation....................................................................................................................................... 4
Chapter 2 Laminator Configurations................................................................................................... 5
Connection ...................................................................................................................................... 6
Version ............................................................................................................................................ 6
Serial Number.................................................................................................................................. 6
Lamination Mode............................................................................................................................ 6
Adjust Speed ................................................................................................................................... 7
Adjust TEMP.................................................................................................................................... 7
Adjust Position ................................................................................................................................ 7
Film Tag INFO .................................................................................................................................. 8
Chapter 3 : Error Messages................................................................................................................. 9
LAMI COM Error / D0-01 ............................................................................................................. 9
LAMI COM Error / D0-02............................................................................................................. 9
LAMI Not Detect / D1-01............................................................................................................. 9
LAMI Film Empty / D2-01 ............................................................................................................ 9
LAMI Film Error / D3-01 .............................................................................................................. 9
LAMI Film Error / D3-02 .............................................................................................................. 9
LAMI No Film / D4-01.................................................................................................................. 9
LAMI Cover Open / D5-01 ........................................................................................................... 9
LAMI Mechanical / D6-01............................................................................................................ 9
LAMI Hopper Full / D7-01............................................................................................................ 9
Service Call / D8-01 ..................................................................................................................... 9

3IX-R7000 Card Lamination Module Configuration Guide
Preface
Thank you for purchasing the IX-R7000 Card Lamination Module (Laminator). Please read this user
guide to learn how to configure the Laminator with your IX-R7000 Card and Badge Printer (IX-
R7000).
How to Use This Guide
This guide describes how to configure the Laminator and troubleshoot error messages.

4IX-R7000 Card Lamination Module Configuration Guide
Chapter 1 Overview and Setup
The Laminator is an accessory for the IX-R7000. The Laminator streamlines the printing process by
laminating the cards as they are printed by the IX-R7000.
To use the Laminator, it is required to install a special firmware on the IX-R7000. This firmware
allows for the IX-R7000 to communicate with the Laminator. See Firmware Requirements on page
4 for more information.
Visit the below URL to learn more about the IX-R7000 and to download manuals.
www.usa.canon.com/support/p/ix-r7000-id-card-badge-printer
Firmware Requirements
The special IX-R7000 firmware version v.1.51.F01 is required to communicate with the Laminator.
The firmware can be downloaded from the below URL.
https://downloads.canon.com/hsg2022/IXR7000/IX-R7000_151_F01.npr
Please refer to the IX-R7000 User Manual for firmware update instructions.
Installation
The Laminator must be installed against the left side of the IX-R7000 so that the printer output slot
aligns with the Laminator input slot. The Laminator connects to the IX-R7000 via an RS-232C serial
cable to facilitate communication and error handling. The serial cable must be connected to the
(OPTION) port on the IX-R7000. The Laminator must always be turned on first before turning on
the IX-R7000.
Please view the below instruction video for detailed Laminator installation information.
https://downloads.canon.com/hsg2023/IXR7000/laminatorinst.mp4

5IX-R7000 Card Lamination Module Configuration Guide
Chapter 2 Laminator Configurations
The operation panel of IX-R7000 is used to configure the Laminator. The Laminator Setup menu
can be accessed under the User Mode setup menu after installing the IX-R7000 firmware version
v.151.F01. See the diagram below for the IX-R7000 Laminator Setup menu tree.

6IX-R7000 Card Lamination Module Configuration Guide
Connection
The Connection menu displays the current connection state of the Laminator.
The below options can be set from this menu. This setting will not change automatically
depending on the connection state of the Laminator, it must be set manually by the user.
DISCONNECT … Set when the Laminator is not connected. (Default value)
CONNECT … Set when the Laminator is connected.
This setting will be applied after power cycling the IX-R7000.
Version
The Version menu displays the Laminator firmware version.
Serial Number
The Serial Number menu displays the Laminator serial number.
Lamination Mode
The Lamination Mode menu displays the Laminator’s currently set lamination mode.
The below options can be set from this menu.
Front side … Laminates the front side and ejects the card front side up.
Back side … Laminates the back side and ejects the card back side up.
Front and back … Laminates the front side, laminates the back side, and then ejects the card back
side up.
Back and front … Laminates the back side, laminates on the front side, and then ejects the card
front side up.
Front and flip … Laminates the front side and ejects the card back side up.
Back and flip … Laminates the back side and ejects the card front side up.
NoLAMI(Faceup) … Ejects the card front side up without any lamination.

7IX-R7000 Card Lamination Module Configuration Guide
NoLAMI(Facedown) … Ejects the card back side up without any lamination.
NoLAMI(Through) … Ejects the card back side up without any lamination.
NoLAMI(Flip) … Ejects the card front side up without any lamination.
“No data” is shown when the setting has not yet been configured.
Adjust Speed
The Adjust Speed menu displays the Laminator’s current lamination speed. The lamination speed
can be set from this menu. The 1st side lamination speed and 2nd side lamination speed can be
configured separately. The default speed is 10 and it can be set between the range of 0 to 20.
Lowering the number will decrease lamination speed and increasing the number will increase
lamination speed.
Adjust TEMP
The Adjust TEMP menu displays the Laminator’s current temperature setting. The lamination
temperature can be set from this menu. The 1st side lamination temperature and 2nd side
lamination temperature can be configured separately. The default temperature is 12 and it can be
set between the range of 0 to 20. Lowering the number will decrease the lamination temperature
and increasing the number will increase the lamination temperature.
Adjust Position
The Adjust Position menu displays the Laminator’s current lamination position offset.
The lamination position offset can be set from this menu. The default position offset is 10 and it
can be set between the range of 0 to 20. Lowering the number will move the laminated patch up
towards the leading short edge of the card. Increasing the number will move the laminated patch
down towards the trailing short edge of the card.

8IX-R7000 Card Lamination Module Configuration Guide
Film Tag INFO
The Film Tag INFO menu displays information about the film currently loaded in the Laminator.
. Film information is retrieved when the Laminator is turned on or when Reload TAG INFO is
performed. Inaccurate film information may display if the film was replaced and Reload TAG INFO
was not performed.
The below information can be found in this menu.ID … Identifies the type of film installed in the
Laminator. See the below table for information about each ID.
Capacity … The number of prints per film roll.
Remainder … Percentage of prints remaining on the film roll.
1st Side Speed … The recommended 1st side lamination speed for the loaded film.
2nd Side Speed … The recommended 2nd side lamination speed for the loaded film.
Both Side TEMP … The recommended lamination temperature for the loaded film.

9IX-R7000 Card Lamination Module Configuration Guide
Chapter 3 : Error Messages
These error messages appear on the IX-R7000 operational panel when a Laminator error occurs.
LAMI COM Error / D0-01
Buffer overflow. Please try again.
LAMI COM Error / D0-02
No response from the Laminator. Check the connection by referring to Installation on page 4.
LAMI Not Detect / D1-01
The Laminator is not detected. Check the connection by referring to Installation on page 4.
LAMI Film Empty / D2-01
The film ribbon is empty or an error occurred while transferring film to the card. Open the
Laminator cover and check the status of the film ribbon.
LAMI Film Error / D3-01
An error happened while transferring film to the card. Open the Laminator cover and check the
status of the film ribbon.
LAMI Film Error / D3-02
An unsupported film ribbon is installed. Install a supported film ribbon.
LAMI No Film / D4-01
The film ribbon is not detected. Install a film ribbon.
LAMI Cover Open / D5-01
The Laminator cover is open. Close the cover.
LAMI Mechanical / D6-01
Service error. Please contact your service provider.
LAMI Hopper Full / D7-01
The output hopper is full. Remove all cards from output hopper and try again.
Service Call / D8-01
Service error. Please contact your service provider.