Canon NP6512 User manual

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
REVISION 0
FY8-13GB-000
AUG. 1999

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
IMPORTANT
THIS DOCUMENTATION IS PUBLISHED BY CANON INC., JAPAN,TO SERVE AS A SOURCE
OF REFERENCE FOR WORK INTHE FIELD.
SPECIFICATIONS AND OTHER INFORMATION CONTAINED HEREIN MAY VARY SLIGHTLY
FROM ACTUAL MACHINE VALUES OR THOSE FOUND IN ADVERTISING AND OTHER
PRINTED MATTER.
ANYQUESTIONSREGARDINGINFORMATION CONTAINED HEREIN SHOULDBEDIRECTED
TOTHE COPIER SERVICE DEPARTMENT OF THE SALES COMPANY.
THIS DOCUMENTATION IS INTENDED FOR ALL SALES AREAS, AND MAY CONTAIN INFOR-
MATION NOT APPLICABLETO CERTAIN AREAS.
COPYRIGHT © 1999 CANON INC.
Printed in Japan
Imprimé au Japon
Use of this manual should be strictly su-
pervised to avoid disclosure of confidential
information.
Prepared by
OFFICE IMAGING PRODUCTSTECHNICAL SUPPORT DIVISION
CANON INC.
5-1, Hakusan 7-chome,Toride-shi, Ibaraki 302-8501 Japan

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
i
INTRODUCTION
This service manual has been prepared for NP6512, NP6612, NP7120, NP7130, and
NP7130F, providing basic information used for servicing the machines in the field so as to
ensure their quality and performance.
This service manual consists of the following chapters:
Chapter 1
General Description introduces the machine's features, specifications,
names of parts, and how originals are reproduced.
Chapter 2
Basic Operation explains how copies are made on a step-by-step basis.
Chapter 3
Exposure System discusses the principles of operation used for the
machine's exposure system. It also explains the timing at which exposure-
related mechanisms are operated, and shows how they may be
disassembled/assembled and adjusted.
Chapter 4
Image Formation System discusses the principles of operation used for the
machine's image formation system. It also explains the timing at which image
formation-related mechanisms are operated, and shows how they may be
disassembled/assembled and adjusted.
Chapter 5
Pick-Up/Feeding System discusses the principles of operation used for the
machine's pickup/feeding system. It also explains the timing at which pickup/
feeding-related mechanisms are operated, and shows how they may be
disassembled/assembled and adjusted.
Chapter 6
Fixing System discusses the principles of operation used for the machine's
fixing system. It also explains the timing at which fixing-related mechanisms
are operated, and shows how they may be disassembled/assembled and
adjusted.
Chapter 7
Externals/Auxiliary Mechanisms discusses the principles of operation used
for the machine's externals/auxiliary mechanisms. It also explains the timing
at which auxiliary mechanism-related mechanisms are operated, and shows
how they may be disassembled/assembled and adjusted.
Chapter 8
ADF explains the principles of operation of the ADF in view of electrical and
mechanical functions and in relation to their timing of operation. It also shows
how the unit may be disassembled/assembled and adjusted.
Chapter 9
Installation introduces requirements for the site of installation, and shows
how the machine may be installed using step-by-step instructions.
Chapter 10
Maintenance and Servicing provides tables of periodically replaced parts and
consumables/durables and scheduled servicing charts.
Chapter 11
Troubleshooting provides tables of maintenance/inspection, standards/
adjustments, and problem identification (image fault/malfunction).
Appendix contains a general timing chart and general circuit diagrams.

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
ii
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specific functions and the
relationship between electrical and mechanical systems with reference to the timing
of operation.
Inthe diagrams, represents the path of mechanical drive—where a signal name
accompanies the symbol , the arrow indicates the direction of the electric sig-
nal.
The expression “turn on the power” means flipping on the power switch, closing the
front door, and closing the delivery unit door, which results in supplying the machine
with power.
2. In the digital circuits, ‘1’ is used to indicate that the voltage level of a given signal is
“High,” while ‘0’ is used to indicate “Low.” (The voltage value, however, differs from
circuit to circuit.)
Inpracticallyallcases,the internal mechanisms of amicroprocessor cannotbe checked
in the field. Therefore, the operations of the microprocessors used in the machines
are not discussed: they are explained in terms of from sensors to the input of the DC
controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for
product improvement or other reasons, and major changes will be communicated in the
form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this
Service Manual and all relevant Service Information bulletins and be able to identify and
isolate faults in the machine.

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
iii
Model
NP6512
NP6612
NP7120
NP7120
NP7130
NP7130
NP7130F
Type
code
TWA
TXA
PUB
PUC
NVF
PTZ
NVH
Default
ratio
2R2E
2R2E
2R2E
2R2E
3R1E
2R2E
3R1E
ADF as
standard
√
√
Cassette
250 sheets
250 sheets
Universal
Universal
500 sheets
500 sheets
500 sheets
The notation “√” indicates that the item in question is available.
• This service manual covers the models shown in the following table. Be sure to have a
good understanding of the difference from model to model before referring to this
manual.

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
v
CONTENTS
CHAPTER 1 GENERAL DESCRIPTION
CHAPTER 2 BASIC OPERATION
CHAPTER 3 EXPOSURE SYSTEM
I. FEATURES ..................................1-1
II. SPECIFICATIONS .......................1-2
A. Copier....................................1-2
B. ADF .......................................1-6
III. NAMES OF PARTS .....................1-8
A. External View ........................1-8
B. Cross Section..................... 1-11
IV. USING THE MACHINE ............. 1-13
A. Control Panel...................... 1-13
B. User mode.......................... 1-15
V. ROUTINE MAINTENANCE BY THE
USER ........................................ 1-16
VI. IMAGE FORMATION ................ 1-19
A. Outline................................ 1-19
I. BASIC OPERATIONS ..................2-1
A. Functional Construction ........2-1
B. Outline of Electrical
Circuitry .................................2-2
C. Basic Sequence of
Operations.............................2-3
D. Controlling the Main
Motor (M1).............................2-5
E. Inputs to and Outputs from the
DC Controller ........................2-7
I. OPERATIONS ..............................3-1
A. Outline...................................3-1
B. Varying the Reproduction
Ratio......................................3-2
C. Lens Drive System................3-3
D. Scanner Drive System ..........3-4
II. EXPOSURE SYSTEM .................3-9
A. Controlling the Scanning
Lamp .....................................3-9
III. DISASSEMBLY/ASSEMBLY ..... 3-13
A. Scanner Drive Assembly.... 3-14
B. Lens Drive Assembly ......... 3-32
C. Exposure System............... 3-38

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
vi
CHAPTER 4 IMAGE FORMATION SYSTEM
CHAPTER 5 PICK-UP/FEEDING SYSTEM
I. IMAGE FORMATION SYSTEM ...4-1
A. Outline...................................4-1
B. Timing Chart for the Image
Formation System .................4-3
C. Primary Charging Roller Bias
Control...................................4-4
D. Controlling the Transfer Roller
Bias .......................................4-9
E. Controlling the Developing/
Separation Static Eliminator
Bias .................................... 4-12
F. Measuring the Density of
Originals ............................. 4-18
G. Controlling the Pre-Exposure
Lamp .................................. 4-24
H. Controlling the Side Blanking
Mechanism......................... 4-26
II. DEVELOPING ASSEMBLY
/CLEANING ASSEMBLY........... 4-27
A. Outline................................ 4-27
B. Detecting the Level of
Toner .................................. 4-28
C. Detecting Waste Toner ....... 4-30
D. Primary Charging Roller
Cleaning Control ................ 4-31
III. DISASSEMBLY/ASSEMBLY ..... 4-33
A. Drum Unit ........................... 4-34
B. Transfer Charging
Assembly............................ 4-38
C. Blank Exposure.................. 4-39
D. Developing Assembly......... 4-43
I. PICKUP/FEEDING SYSTEM.......5-1
A. Outline...................................5-1
B. Controlling the Pickup
Roller .....................................5-2
C. Controlling the Movement of
Paper.....................................5-6
D. Detecting Jams .....................5-8
II. DISASSEMBLY/ASSEMBLY ..... 5-13
A. Pickup Assembly................ 5-14
B. Multifeeder Assembly......... 5-21
C. Feeding Assembly.............. 5-24
D. Registration Roller
Assembly............................ 5-25
E. Delivery Assembly.............. 5-30
CHAPTER 6 FIXING SYSTEM
I. OPERATIONS..............................6-1
A. Outline...................................6-1
B. Controlling the Fixing
Temperature ..........................6-3
II. DISASSEMBLY/ASSEMBLY ........6-9
A. Fixing Assembly ................. 6-10

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
vii
CHAPTER 7 EXTERNALS/AUXILIARY MECHANISMS
CHAPTER 8 ADF
CHAPTER 9 INSTALLATION
I. FANS............................................7-1
II. POWER SUPPLY SYSTEM.........7-3
A. Outline of the Power Supply
System ..................................7-3
B. Power Supply Circuit .............7-4
C. Detecting an Error on the Com-
posite Power Supply PCB .....7-6
D. Protecting the Power Supply
Circuit ....................................7-6
III. DISASSEMBLY/ASSEMBLY ........7-7
A. External Covers.....................7-8
B. Control Panel...................... 7-15
C. Copyboard Glass ............... 7-16
D. Main Motor/Main Drive Assem-
bly....................................... 7-17
E. Electrical System ............... 7-21
I. ADF ..............................................8-1
A. Outline...................................8-1
B Basic Construction ................8-2
C. Basic Operations...................8-4
D. Detecting an Original ............8-6
E. Pickup Operation...................8-8
F. Delivery .............................. 8-12
G. Controlling the Pickup
Motor .................................. 8-14
H. Controlling the Belt Motor .. 8-15
I. Detecting Original Jams..... 8-16
J. Power Supply ..................... 8-17
II. DISASSEMBLY/ASSEMBLY ..... 8-18
A. Removing the ADF............. 8-19
B. External Covers.................. 8-21
C. Drive System...................... 8-23
D. Feeding System ................. 8-26
E. Electrical System ............... 8-33
I. SELECTING THE SITE ...............9-1
II. UNPACKING AND
INSTALLATION ............................9-2
A. Unpacking and Installation....9-2
B. Placing Copy Paper............ 9-18
III. MOVING THE MACHINE .......... 9-21
CHAPTER 10 MAINTENANCE AND SERVICING
I. PERIODICALLY REPLACED
PARTS....................................... 10-1
II. DURABLES AND
CONSUMABLES ...................... 10-1
III. SCHEDULED SERVICING ....... 10-1

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
viii
APPENDIX
CHAPTER 11 TROUBLESHOOTING
A. GENERAL TIMING CHART........ A-1
B. SIGNALS AND
ABBREVIATIONS ....................... A-3
C. GENERAL CIRCUIT DIAGRAM . A-5
D. DC CONTROLLER CIRCUIT
DIAGRAM ................................... A-7
E. ADF CONTROLLER CIRCUIT
DIAGRAM ................................. A-15
F. COMPOSITE POWER SUPPLY
CIRCUIT DIAGRAM.................. A-19
G. CONTROL PANEL CIRCUIT
DIAGRAM ................................. A-29
H. AE SENSOR CIRCUIT
DIAGRAM ................................. A-31
I. SENSOR CIRCUIT
DIAGRAM ................................. A-32
J. NOISE FILTER CIRCUIT
DIAGRAM ................................. A-33
K. HIGH VOLTAGE CONTACT CIRCUIT
DIAGRAM ................................. A-34
L. BLANK EXPOSURE (front) CIRCUIT
DIAGRAM ................................. A-35
M. BLANK EXPOSURE (rear) CIRCUIT
DIAGRAM ................................. A-36
N. PRE-EXPOSURE CIRCUIT
DIAGRAM ................................. A-37
O. SPECIAL TOOLS...................... A-38
P. SOLVENTS/OILS ...................... A-39
I. MAINTENANCE AND
INSPECTION ............................ 11-3
A. Image Adjustment Basic
Procedure........................... 11-3
B. Points to Note for
Servicing ............................ 11-4
II. STANDARDS AND
ADJUSTMENTS ....................... 11-5
A. Mechanical ......................... 11-5
B. ADF .................................. 11-30
C. Electrical........................... 11-41
III. TROUBLESHOOTING IMAGE
FAULTS ................................... 11-52
A. Making Initial Checks ....... 11-52
B. Sample Image Faults ....... 11-56
C. Troubleshooting Image
Faults................................ 11-57
IV.TROUBLESHOOTING
MALFUNCTIONS.................... 11-65
A. Troubleshooting
Malfunctions ..................... 11-65
V. TROUBLESHOOTING FEEDING
PROBLEMS ............................ 11-77
A. Copy Paper Jam............... 11-77
B. Faulty Feeding.................. 11-80
VI. ARRANGEMENT AND FUNCTIONS
OF ELECTRICAL PARTS ....... 11-81
A. Sensors and Solenoids.... 11-81
B. Switches........................... 11-82
C. Lamp, Heater, Motor, Etc. 11-83
D. PCBs ................................ 11-84
E. ADF .................................. 11-85
F. Variable Resistors (VR) and
Check Pins by PCB.......... 11-86
VII. SERVICE MODE..................... 11-88
A. Outline.............................. 11-88
B. Using Service Mode......... 11-88
C. Adjustment Mode (30)...... 11-91
D. Operation/Inspection
Mode (40)......................... 11-92
E. Machine Settings
Mode (50)......................... 11-93
F. Counter Mode (60)........... 11-93
VIII.SELF DIAGNOSIS .................. 11-94

COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
GENERAL DESCRIPTION
This chapter provides specifications of the machine, instructions on how to operate
the machine, and an outline of copying process.
I. FEATURES ..................................1-1
II. SPECIFICATIONS .......................1-2
A. Copier....................................1-2
B. ADF .......................................1-6
III. NAMES OF PARTS .....................1-8
A. External View ........................1-8
B. Cross Section..................... 1-11
IV. USING THE MACHINE ............. 1-13
A. Control Panel...................... 1-13
B. User mode.......................... 1-15
V. ROUTINE MAINTENANCE BY THE
USER ........................................ 1-16
VI. IMAGE FORMATION ................ 1-19
A. Outline................................ 1-19

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-1
I. FEATURES
1. Personal Copier with a Zoom Function and a Fixed Copyboard
• You can choose either a default enlargement/reduction ratio or any ratio between 70% and
141% in 1% increments.
2. Ecology-Conscious
• The use of a roller charging method has resulted in a considerable reduction of ozone: 0.01
ppm or less on the average, 0.02 ppm or less at maximum (1/100 to 1/1000 compared with
existing Canon machines).
3. SURF Fixing Assembly
• The wait time is 0 sec (at 20°C room temperature), enabling speedy copying work immedi-
ately after power-on.
4. Various Paper Sizes
• The paper may be between A4 (LGL) and A5 (STMT)(*Using the universal cassette).
• In manual feed mode, paper may be as large as A4 (LGL) or as small as a business card.
5. Large Paper Source
• The source of paper may contain as many as 550 sheets of paper (500-sheet cassette type).
6. Separate top unit.
• The machine’s top unit may be opened to make jam removal easy.
7. ADF Type
• Continuous copying is possible with the use of the ADF.

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-2
Descriptions
Desk top
Fixed
Halogen lamp (80 V/110 W for 120V-model; 150 V/160 W
for 220/240 V-model)
Fixed focal point lens
OPC drum (24-mm dia.)
Item
Body
Copyboard
Source of light
Lens
Photosensitive medium
Descriptions
Indirect static reproduction
Roller (direct charging)
Slit (moving light source)
Auto or manual
Dry (toner projection)
Cassette (1 pc.)
Multifeeder
Curvature separation + static eliminator
Flat heater
Blade
Center reference (copyboard)
Item
Reproduction
Charging
Exposure
Copy density adjustment
Development
Pickup
Separation
Fixing
Cleaning
Original orientation
Table 1-202
Table 1-201
2. Mechanisms
II. SPECIFICATIONS
A. Copier
1. Type

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-3
Descriptions
Sheet, book, 3-D object (2kg max.)
A4 (297 ×210 mm)/LGL (216 ×356 mm)
Inch/AB-configuration: 2R2E Inch-configuration: 3R1E
70% to 141% (in 1% increments)
0 sec (at 20°C room temperature)
10 sec or less (at 20°C room temperature; Direct, non-AE,
from the cassette)
100 (max.)
A4/LGL (297 ×210 mm/216 ×356 mm max.)
Business card (90 ×55 mm, min.)
Cassette:
Plain paper (64 to 80 g/m2), tracing paper (SM-1, A4R/
B5R), colored paper, recycled paper (64 to 80 g/m2; A4R/
B5R), eco paper (80 g/m2; A4R)
Manual Feeder:
Plain paper (52 to 128 g/m2), tracing paper (SM-1, GNT-
80*1; A4R/B5R), transparency*1,*3 (A4R/LTRR*2), colored
paper, business card (200 g/m2or less), label sheet*1 (A4R/
LTRR), recycled paper (64 to 80 g/m2; A4R/B5R), eco
paper (80 g/m2; A4R), postcard*2
Double-Sided/Overlay Copying*4:
Plain paper (64 to 128 g/m2), colored paper, business card
(200 g/m2or less), recycled paper (64 to 80 g/m2; A4R/
B5R), eco paper (80 g/m2; A4R), postcard
With claws
Universal cassette (250 sheets of 80 g/m2paper; A4/LGL to
A5/STMT)
250-sheet cassette (250 sheets of 80 g/m2)
500-sheet cassette (500 sheets of 80 g/m2)
5 mm deep (approx.; 50 sheets of 80 g/m2)
100 sheets (A4; 80 g/m2)
Leading edge: 2.0 ±1.5 mm (Direct; 4.0 mm or less otherwise)
Left/right: 0.0 +2.0, -0.0 mm (0 +4.0, -0.0 mm for LTR)
Provided (5 min, approx.; fixed)*5
Item
Original type
Maximum original size
Reproduction ratio
Zoom
Wait time
First copy time
Continuous copying
Copy size
Copy paper type
Cassette
Multifeeder tray
Copy tray
Non-image width
Auto power-off
Table 1-203
*1. Applies only to single pickup if the multifeeder is used.
*2. Applies only to vertical feeding.
*3. Upon delivery, be sure to remove each from the copy tray.
*4. Be sure to remove any curling before feeding for a second time.
*5. If stopped because paper ran out during copying operation, 1 hr.
3. Performance

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-4
4. Others
Descriptions
7.5°C to 32.5°C/45.5°F to 90.5°F
5% to 85% RH
607.95 to 1013.25 hPa (0.6 to 1 atm)
120 V 60 Hz 220/240 V 50 Hz
NVFxxxxx PTZxxxxx
NVHxxxxx PUBxxxxx
PUCxxxxx
TWAxxxxx
TXAxxxxx
0.9 kW or less
Standby: 1.2 W (approx.; about 5 min; reference only)
Copying: 0.4 kWh (approx.; reference only)
Standby: - (sound power level by ISO)
Copying: 66 dB or less (sound power level by ISO)
0.01 ppm or less (average; 0.02 ppm or less, max.)
Copyboard Type
484.9 ×448.2 ×297.5 mm*1/329.0 mm*2
19.1 in. ×17.6 in. ×11.7 in.*1/13.0 in.*2
ADF Type
484.9 ×448.2 ×358.3 mm*1/389.8 mm*2
19.1 in. ×17.6 in. ×14.1 in.*1/15.3 in.*2
Copyboard Type
20.6 kg*1/45.3 lb*1, 22.5 kg*2/49.5 lb*2
ADF Type
24.4 kg*1/53.7 lb*1, 26.3 kg*2/57.9 lb*2
Copy paper: Keep wrapped, and protect against humidity.
Toner: Avoid direct sunlight, and store at 40°C/104°F, 85%
or less.
Item
Operating condition
Temperature
Humidity
Atmospheric pressure
Power source
Serial number
Maximum power consumption
Noise
Ozone
Dimensions (WxDxH)
Weight (including the cassette)
Consumables
Table 1-204
*1. 250-sheet cassette type
*2. 500-sheet cassette type

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-5
Table 1-205
2R2E (Inch/AB-configuration)
1:1.000
1:0.707
1:0816
1:1.154
1:1.414
Item
Direct
Reduce I
Reduce II
Reduce III
Reduce IV
Enlarge I
Enlarge II
3R1E (Inch-configuration)
1:1.000
1:0.707
1:0.786
1:0.860
1:1.414
5. Default Ratios
Table 1-206
*1. The number of copies starting with the pickup operation that follows the delivery of the
19th copy in a continuous copying job. (See p.5-5)
The specifications are subject to change for product improvement.
Number of copies
( Multifeeder*1)
(copies/min)
13 (9)
11 (8)
13 (9)
13 (9)
13 (9)
13 (9)
10 (9)
12 (9)
12 (9)
12 (9)
12 (9)
12 (9)
12 (9)
10 (9)
Copy size
LTRR
LGL
STMTR
MIN
LGL →LTRR
MARJIN
MAX
A4R
B5R
A5R
A4R →A5R
B5R →A5R
B5R →A4R
A5R→A4R
Reproduction ratio
Direct
Reduce I (70.7%)
Reduce II (78.6%)
Reduce IV (86.0%)
Enlarge II (141.4%)
Direct
Reduce I (70.7%)
Reduce III (81.6%)
Enlarge I (115.4%)
Enlarge II (141.4%)
Copying speed at
Direct
13
12
6. Copying Speed

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-6
Table 1-207
Descriptions
Auto pickup/delivery
Face-down
Center reference
Top separation
Single-sided (50 to 128 g/m2)
A5 (STMT) to A4R (LTRR), LGL
Length: 139.7 to 355.6 mm (feeding direction)
Width: 139.7 to 215.9 mm
30 sheets (80 g/m2or less; about 3 mm in height)
Single-sided original to single-sided copy
Yes (in feeding direction)
No
Yes
446 mm/sec
IPC
Width: 474 mm/18.7 in. (659 mm/25.9 in. with the tray open)
Depth: 394 mm/15.5in.
Height: 74 mm/2.9 in. (216 mm/8.5 in. with the tray open)
5 kg/11 lb (approx.)
24 VDC and 5 VDC (from the host)
40 W or less
Temperature: same as the host
Humidity: same as the host
Item
Original pickup
Original orientation
Original position
Original separation
Original type
Stack
Original processing mode
Original size detection
Mixed original sizes
Original detection
Original feeding speed
Communication with host
Dimensions
Weight
Power source
Maximum power consumption
Operating environment
B. ADF

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-7
*1. The following may not be used as an original:
• Sheet with a staple, clip, or glue.
• Sheet with a cut, hole, or tear.
• Sheet with holes for binding.
• Sheet with a carbon back.
• Sheet with a cut-and-paste piece.
• Sheet with curling, bending, or wrinkling.
The specifications are subject to change for product improvement.

CHAPTER 1 GENERAL DESCRIPTION
COPYRIGHT © 1999 CANON INC. CANON NP6512/6612/7120/7130/7130F REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON) 1-8
III. NAMES OF PARTS
A. External View
1. Copyboard Type
Figure 1-301
Figure 1-302
[1] Copy tray
[2] Power cord connector
[3] Open/close lever
[1] Copyboard cover
[2] Static eliminator cleaner
[3] Manual feed tray
[4] Right door
[5] Cassette
[6] Copyboard glass
[4] Copy density correction dial
[5] Static eliminator
[6] Delivery guide plate
[1]
[6]
[5]
[2]
[3]
[4]
[6]
[2]
[1]
[3]
[4]
[5]