Canon WUX500ST Installation manual

© CANON INC.2017 YT1-1471-000
MULTIMEDIA PROJECTOR
WUX500ST
User Commands

WUX500ST User Commands
- -
ii
Table of Contents
Table of Contents ........................................................................................................ii
1. Overview .................................................................................................................1
2. Communication Specifications ................................................................................2
Communication Specifications................................................................................................................ 2
Usable Character Codes......................................................................................................................... 4
Communication System (Serial).............................................................................................................. 5
Communication System (LAN)................................................................................................................ 5
Communication system (HDBaseT)........................................................................................................ 5
Command Format................................................................................................................................... 6
Response Format.................................................................................................................................... 6
Other Items............................................................................................................................................. 8
3. Communication Flow...............................................................................................9
Command Transmission (PC side).......................................................................................................... 9
Command Reception (projector side)...................................................................................................... 9
Command/Response .............................................................................................................................. 9
Response Reception Timeout................................................................................................................. 9
Other Items............................................................................................................................................. 9
4. Command List .......................................................................................................10
5. Guide to Command Description ............................................................................13
EXAMPLE............................................................................................................................................. 13
6. Command Details..................................................................................................15
6AXADJ ................................................................................................................................................ 15
6AXR..................................................................................................................................................... 16
6AXG .................................................................................................................................................... 17
6AXB..................................................................................................................................................... 18
6AXC..................................................................................................................................................... 19
6AXM.................................................................................................................................................... 20
6AXY..................................................................................................................................................... 21
AMBADJ ............................................................................................................................................... 22
AMBLEVEL........................................................................................................................................... 23
AMBTYPE............................................................................................................................................. 24
ASELA1 ................................................................................................................................................ 25
ASELA2 ................................................................................................................................................ 26
ASELC.................................................................................................................................................. 27
ASELD.................................................................................................................................................. 28
ASELH.................................................................................................................................................. 29
ASELHDBT........................................................................................................................................... 30
ASELL................................................................................................................................................... 31
ASELU.................................................................................................................................................. 32
ASPECT................................................................................................................................................ 33
AUTOPC............................................................................................................................................... 34
AUTOSETEXE...................................................................................................................................... 35
AVOL..................................................................................................................................................... 36
BLANK.................................................................................................................................................. 37

WUX500ST User Commands
- -
iii
BRI........................................................................................................................................................ 38
COLOR_TEMP ..................................................................................................................................... 39
COMVER.............................................................................................................................................. 40
CONT.................................................................................................................................................... 41
DGAMMA.............................................................................................................................................. 42
DZOOM_POS....................................................................................................................................... 43
DZOOM_RAT........................................................................................................................................ 44
ERR ...................................................................................................................................................... 45
FINE_GAMMA_R.................................................................................................................................. 46
FINE_GAMMA_G.................................................................................................................................. 47
FINE_GAMMA_B.................................................................................................................................. 48
FLTWRN ............................................................................................................................................... 49
FNBND.................................................................................................................................................. 50
FREEZE................................................................................................................................................ 51
GAMMA ................................................................................................................................................ 52
HDMI_IN............................................................................................................................................... 53
HTMPINF.............................................................................................................................................. 54
HUE ...................................................................................................................................................... 55
IMAGE .................................................................................................................................................. 56
IMAGEFLIP........................................................................................................................................... 57
INPUT................................................................................................................................................... 58
KREP.................................................................................................................................................... 59
LAMP.................................................................................................................................................... 60
LAMPCOUNTER................................................................................................................................... 61
LMPWRN.............................................................................................................................................. 62
MAIN..................................................................................................................................................... 63
MEMF ................................................................................................................................................... 65
MEMG................................................................................................................................................... 66
MEMS................................................................................................................................................... 67
MUTE.................................................................................................................................................... 68
NR......................................................................................................................................................... 69
NRMPG................................................................................................................................................. 70
NRMSQT .............................................................................................................................................. 71
OVSCAN............................................................................................................................................... 72
POWER ................................................................................................................................................ 73
PRODCODE ......................................................................................................................................... 74
RC......................................................................................................................................................... 75
RGBGAIN ............................................................................................................................................. 77
RGBOFFSET........................................................................................................................................ 78
ROMVER.............................................................................................................................................. 79
SAT....................................................................................................................................................... 80
SAVEIMGPROF.................................................................................................................................... 81
SCRNASPECT ..................................................................................................................................... 82
SHARP.................................................................................................................................................. 83
SIGMSG................................................................................................................................................ 84
SIGNAL_INFO ...................................................................................................................................... 85
SIGNALSTATUS ................................................................................................................................... 86
TEMP.................................................................................................................................................... 87
TPTN..................................................................................................................................................... 88
ZSCLR.................................................................................................................................................. 90
7. Error List................................................................................................................91
8. Error Processing....................................................................................................92

WUX500ST User Commands
-1-
1. Overview
These specifications describe the methods of controlling Projector WUX500ST from PC or other controllers
over an RS-232C, wired LAN, wireless LAN, or HDBaseT connection.
Symbols
The following symbols are used in these specifications:
Symbol
Description
[ ]
Data in [ ] can be omitted.
|
Same as OR.

WUX500ST User Commands
-2-
2. Communication Specifications
Communication Specifications
The projector can be controlled via RS-232C, wired LAN, HDBaseT, or wireless LAN connection.
PC - Projector connection configuration
RS-232C connection
Wired LAN connection
Item
Specification
Item
Specification
Connection
system
PC and projector connected on a "1:1"
basis
Connection
system
TCP/IP connection
Connection
signal line
3-line connection of SD, RD, and SG
Connection
signal line
Straight when connecting via network
Connection
cable
9-pin RS-232C cable (crossover)
Connection
cable
LAN cable
LAN
1000BASE-T
100BASE-TX
10BASE-T
HDBaseT connection
Wireless LAN connection
Item
Specification
Item
Specification
Connection
system
HDBaseT connection
Connection
system
802.11bgn
Connection
cable
LAN cable
* Signal lines other than the three SD, RD, and SG lines are not used in the projector.
* Loop back its own signals on the PC side as necessary.
* To use the wired LAN connection, on the projector, the wired side of "network (wired/wireless)" must be
turned on.
* To use the HDBaseT connection, on the projector, HDBaseT must be turned on and serial communication
must be set to HDBaseT.
SD
SD
RD
RD
SG
SG
送信データ
送信データ
受信データ
信号用設置
信号用設置
受信データ
Send Data
Receive Data
Signal Ground
Send Data
Receive Data
Signal Ground
Projector
SERVICE
PORT
Network connection
LAN PORT
LAN PORT
RS-232C
crossover cable
クロスｹｰﾌﾞﾙ
PC
HDBaseT TX
COM PORT
HDBaseTCOM PORT
PC
PC
COM PORT
Wireless LAN
connection
PC

WUX500ST User Commands
-3-
* To use the wireless connection, on the projector, the wireless side of "network (wired/wireless)" must be
set to Infra or Pi AP.

WUX500ST User Commands
-4-
Usable Character Codes
Use ASCII codes in the red and blue areas of the following table.
No distinction is made between double-byte characters and single-byte characters. All characters are
interpreted as single-byte characters, so do not use double-byte or triple-byte characters.
Uppercase and lowercase alphabet letters are recognized as the same character.
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
NUL
SP
0
@
P
`
p
1
!
1
A
Q
a
q
2
"
2
B
R
b
r
3
#
3
C
S
c
s
4
$
4
D
T
d
t
5
%
5
E
U
e
u
6
&
6
F
V
f
v
7
'
7
G
W
g
w
8
(
8
H
X
h
x
9
)
9
I
Y
i
y
A
*
:
J
Z
j
z
B
+
;
K
[
k
{
C
,
<
L
\
l
|
D
CR
-
=
M
]
m
}
E
.
>
N
^
n
~
F
/
?
O
_
o
Item
Specifications
Delimiters
CR(0Dh)
Characters usable as delimiters.
General characters
20h to 60h, 7Bh to 7Eh
Characters usable in commands.
Invalid characters
Do not use the codes in regions other than the red and blue areas or invalid characters.
If used, it will be handled as a space (20h).
Unrecommended
characters
Do not use as a general rule.
Both upper case and lower case letters can be used in commands, but upper case should
be used in most cases.

WUX500ST User Commands
-5-
Communication System (Serial)
Item
Specification
Communication mode
RS-232-C Start-stop synchronization half-duplex communication
Transmission speed
19.2 Kbps
Character length
8 bits/character
Stop bit
2 bits
Parity
None
Command format
Variable-length records with terminals as delimiters
Maximum transmission length
Maximum of 256 characters (bytes) including delimiters.
Delimiters
CR (0Dh) can be used as a delimiter.
Delimiter in the response is CR.
Command code
ASCII codes (20h to 7Eh)
Codes other than ASCII codes (20h to 7Eh), delimiter code (0Dh), or NUL (00h) are
handled as spaces (20h).
Communication procedure
No procedure
Flow control
None
Error control
None
Break signal
Not supported
Timeout
Tc
Between characters:
1 second
Tr
Between command/response interval:
15 seconds
* For timeout, see chapter 3, "Communication Flow" on page 9.
Communication System (LAN)
Item
Specification
Communication mode
TCP/IP connection. Port: 33336
Remarks
If a command is not received for 30 seconds, the socket will be closed.
Communication system (HDBaseT)
Item
Specification
Communication mode
RS-232-C Start-stop synchronization half-duplex communication
Transmission speed
9600bps
Character length
8 bits/character
Stop bit
2 bits
Parity
None
Command format
Variable-length records with terminals as delimiters
Maximum transmission length
Maximum of 256 characters (bytes) including delimiters.
Delimiters
CR (0Dh) can be used as a delimiter.
Delimiter in the response is CR.
Command code
ASCII codes (20h to 7Eh)
Anything other than the above code and delimiter codes are processed in the same
way as space (20h).
Communication procedure
No procedure
Flow control
None
Error control
None
Break signal
Not supported
Timeout
Tc
Between characters:
1 second
Tr
Between command/response interval:
15 seconds
* For timeout, see chapter 3, "Communication Flow" on page 9.

WUX500ST User Commands
-6-
Command Format
Format
Commands are sent from PC to the projector in the following format:
<command text><delimiter> or
<command text>=(value>(delimiter>
<command text>
Character strings consisting of 1 or more alphanumeric letters
<value>
Character strings consisting of 1 or more alphanumeric letters
<delimiter>
CR(0Dh)
For <command strings> and <value>, see explanation about each command.
Example) When checking the power status (POWER)
PC → PJ
G
E
T
=
P
O
W
E
R
CR
47h
45h
54h
3Dh
50h
4Fh
57h
45h
52h
0Dh
Response Format
Responses are sent from the projector to PC in the following format:
<Response character string> <Delimiter>
There are multiple response types, each having different <response string> format.
<Response character
string>
Character strings consisting of 1 or more alphanumeric letters
First 2 digits are always 1 lowercase alphabet letter and a ":" (colon).
The first character indicates the response type.
Response
type
Meaning
Example
i
Normal response
i:OK
g
Reference
command
response
g:BRI=0
e
Error response
e:0002 INVALID_COMMAND
<delimiter>
CR(0Dh)
Format varies according to the type, as follows:
Normal response
A response when command is processed normally.
The projector receives the next command only after receiving this response.
Format)
i:OK<delimiter>

WUX500ST User Commands
-7-
Example)
PC → PJ
P
O
W
E
R
=
O
N
CR
50h
4Fh
57h
45h
52h
3Dh
4Fh
4Eh
0Dh
PC ← PJ
i
:
O
K
CR
69h
3Ah
4Fh
4Bh
0Dh
Reference command response
A response when reference is made properly for a reference command.
Format)
g:<command string>=<value><delimiter>
Example)
PC → PJ
G
E
T
=
P
O
W
E
R
CR
47h
45h
54h
3Dh
50h
4Fh
57h
45h
52h
0Dh
PC ← PJ
g
:
P
O
W
E
R
=
O
N
CR
67h
3Ah
50H
4Fh
57h
45h
52h
3Dh
4Fh
4Eh
0Dh
Error response
A response when an error occurred.
Format)
e:<error ID><space><error info string><delimiter>
<error ID>
4 alphanumeric letters
<space>
Space character (20h)
<error info string>
Character strings consisting of 1 or more alphanumeric letters
* Refer to “Error List”
Example)
PC → PJ
A
U
T
O
P
C
CR
41h
55h
54h
4Fh
50h
43h
0Dh
PC ← PJ
e
:
2
0
1
F
I
N
V
A
L
I
D
_
65h
3Ah
32h
30h
31h
46h
20h
49h
4Eh
56h
41h
4Ch
49h
44h
5Fh
S
I
G
N
A
L
CR
53h
49h
47h
4Eh
41h
4Ch
0Dh

WUX500ST User Commands
-8-
Normal response (BUSY)
This response is sent when a command cannot be received during processing.
Format)
i:BUSY<delimiter>
Example)
PC → PJ
A
U
T
O
P
C
CR
41h
55h
54h
4Fh
50h
43h
0Dh
PC ← PJ
i
:
B
U
S
Y
CR
69h
3Ah
42h
55h
53h
59h
0Dh
Other Items
Command recognition
The receiver (projector) retains incoming characters within a specific Tc, and recognizes the data as
"received command" when delimiter is received.
If the character interval received exceeds the Tc or if a delimiter is not received within 256 characters, all
data already received is lost, and the mode is reset to standby to receive commands again.
Parameter value
Definition of <Parameter value> is as follows:
<Parameter value>
<value 1>, <value 2>…,<value n>
<value n>
<Numerical value> | <ID> | “<Character string>”
<numerical value>
[<sign>]<decimal numeric string >
The decimal string consists of minimum 1 letter and maximum 5 letters.
Valid value range is -32768 to 32767.
<ID>
1 or more ASCII characters (20h to 60h, 7Bh to 7Eh)
<character string>
0 or more ASCII characters (20h to 60h, 7Bh to 7Eh)

WUX500ST User Commands
-9-
3. Communication Flow
Command Transmission (PC side)
Commands should be sent from PC in a way that each character is sent within the specified Tc
(inter-character timeout).
Command Reception (projector side)
The projector retains incoming characters within a specific Tc, and recognizes the data as "received
command" when delimiter is received.
If the character interval received exceeds the Tc or if a delimiter is not received within 256 characters, all
data already received is lost, and the mode is reset to standby to receive commands again.
Command/Response
A response is always returned within Tr(*) for a command sent from the PC.
(*) The timeout interval between command and response (Tr) is 15 seconds.
Response Reception Timeout
If a response is not received within the Tr (timeout interval between command and response) while standing
by a waiting response after sending a command from the PC, it is deemed to have exceeded the “response
reception timeout.” Please resend the command.
Other Items
To execute commands via wired LAN or wireless LAN, the wired LAN or wireless LAN function must be
enabled in advance.
To execute commands via HDBaseT, the HDBaseT function must be enabled and serial communication
must be set to HDBaseT in advance.
The PC side cannot send the next user command before a response for the first command is returned. If
two or more user commands are received, user commands from 2nd one are discarded. If 2 or more user
commands are received, only the 1st command is processed, and a response is returned when finished.
For commands sent via wired LAN or wireless LAN, if multiple commands are embedded in a single packet,
the projector processes the first command and discards the rest.
PC
プロジェクター
Tr以内
コマンド
レスポンス
Command
Response
Within Tr
Command 1
Response to Command 1
Command 2
Command 3
Projector
Within Tr
Projector

WUX500ST User Commands
-10-
4. Command List
Item
Command
Setting
Reference
Description
Power mode restriction
LAN
RS-232C
SL0
SL1
SL3
PM
ON
ST
PM
ON
1
6AXADJ
Yes
Yes
6-axis color adjustment
-
-
-
-
Yes
-
-
Yes
2
6AXR
Yes
Yes
6-axis color adjustment R hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
3
6AXG
Yes
Yes
6-axis color adjustment G hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
4
6AXB
Yes
Yes
6-axis color adjustment B hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
5
6AXC
Yes
Yes
6-axis color adjustment C hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
6
6AXM
Yes
Yes
6-axis color adjustment M hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
7
6AXY
Yes
Yes
6-axis color adjustment Y hue/saturation/brightness
-
-
-
-
Yes
-
-
Yes
8
AMBADJ
Yes
Yes
Ambient light correction adjustment ON/OFF
-
-
-
-
Yes
-
-
Yes
9
AMBLEVEL
Yes
Yes
Ambient light level settings
-
-
-
-
Yes
-
-
Yes
10
AMBTYPE
Yes
Yes
Ambient light type settings
-
-
-
-
Yes
-
-
Yes
11
ASELA1
Yes
Yes
Analog PC-1 Audio input terminal selection
-
-
-
-
Yes
-
-
Yes
12
ASELA2
Yes
Yes
Analog PC-2 Audio input terminal selection
-
-
-
-
Yes
-
-
Yes
13
ASELC
Yes
Yes
Component Audio input terminal selection
-
-
-
-
Yes
-
-
Yes
14
ASELD
Yes
Yes
Digital PC Audio input terminal selection
-
-
-
-
Yes
-
-
Yes
15
ASELH
Yes
Yes
HDMI Audio input terminal selection
-
-
-
-
Yes
-
-
Yes
16
ASELHDBT
Yes
Yes
HDBaseT Audio input terminal selection
Yes
Yes
17
ASELL
Yes
Yes
LAN audio input terminal selection
-
-
-
-
Yes
-
-
Yes
18
ASELU
Yes
Yes
USB audio input terminal selection
-
-
-
-
Yes
-
-
Yes
19
ASPECT
Yes
Yes
Aspect ratio
-
-
-
-
Yes
-
-
Yes
20
AUTOPC
Yes
-
Auto PC
-
-
-
-
Yes
-
-
Yes
21
AUTOSETEXE
Yes
-
Auto setup
-
-
-
-
Yes
-
-
Yes
22
AVOL
Yes
Yes
Audio volume adjustment
-
-
-
-
Yes
-
-
Yes
23
BLANK
Yes
Yes
Screen blank
-
-
-
-
Yes
-
-
Yes
24
BRI
Yes
Yes
Brightness setting
-
-
-
-
Yes
-
-
Yes
25
COLOR_TEMP
Yes
Yes
Color temperature setting
-
-
-
-
Yes
-
-
Yes
26
COMVER
-
Yes
User command version inquiry
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
27
CONT
Yes
Yes
Contrast setting
-
-
-
-
Yes
-
-
Yes
28
DGAMMA
Yes
Yes
Dynamic gamma
-
-
-
-
Yes
-
-
Yes
29
DZOOM_POS
Yes
Yes
Zoom display position
-
-
-
-
Yes
-
-
Yes
30
DZOOM_RAT
Yes
Yes
Zoom display ratio
-
-
-
-
Yes
-
-
Yes
31
ERR
-
Yes
Error information inquiry
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
32
FINE_GAMMA_R
Yes
Yes
Fine gamma (R)
-
-
-
-
Yes
-
-
Yes
33
FINE_GAMMA_G
Yes
Yes
Fine gamma (G)
-
-
-
-
Yes
-
-
Yes
34
FINE_GAMMA_B
Yes
Yes
Fine gamma (B)
-
-
-
-
Yes
-
-
Yes
35
FLTWRN
Yes
Yes
Air filter cleaning warning
-
-
-
-
Yes
-
-
Yes
36
FNBND
Yes
Yes
[Fn] button setting
-
-
-
-
Yes
-
-
Yes
37
FREEZE
Yes
Yes
Screen freeze
-
-
-
-
Yes
-
-
Yes
38
GAMMA
Yes
Yes
Gamma adjustment
-
-
-
-
Yes
-
-
Yes
39
HDMI_IN
Yes
Yes
HDMI input setting
-
-
-
-
Yes
-
-
Yes
40
HTMPINF
Yes
Yes
High temperature caution display
-
-
-
-
Yes
-
-
Yes

WUX500ST User Commands
-11-
Item
Command
Setting
Reference
Description
Power mode restriction
LAN
RS-232C
SL0
SL1
SL3
PM
ON
ST
PM
ON
41
HUE
Yes
Yes
Hue setting
-
-
-
-
Yes
-
-
Yes
42
IMAGE
Yes
Yes
Image mode setting
-
-
-
-
Yes
-
-
Yes
43
IMAGEFLIP
Yes
Yes
Flip display
-
-
-
-
Yes
-
-
Yes
44
INPUT
Yes
Yes
Input signal selection
-
-
-
-
Yes
-
-
Yes
45
KREP
Yes
Yes
Key repeat
-
-
-
-
Yes
-
-
Yes
46
LAMP
Yes
Yes
Lamp mode
-
-
-
-
Yes
-
-
Yes
47
LAMPCOUNTER
-
Yes
Lamp counter inquiry
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
48
LMPWRN
Yes
Yes
Lamp replacement warning display
-
-
-
-
Yes
-
-
Yes
49
MAIN
Yes
-
Unit control panel emulation
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
50
MEMF
Yes
Yes
Memory color adjustment (flesh)
-
-
-
-
Yes
-
-
Yes
51
MEMG
Yes
Yes
Memory color adjustment (green)
-
-
-
-
Yes
-
-
Yes
52
MEMS
Yes
Yes
Memory color adjustment (sky)
-
-
-
-
Yes
-
-
Yes
53
MUTE
Yes
Yes
Audio mute
-
-
-
-
Yes
-
-
Yes
54
NR
Yes
Yes
Random noise reduction
-
-
-
-
Yes
-
-
Yes
55
NRMPG
Yes
Yes
MPEG noise reduction
-
-
-
-
Yes
-
-
Yes
56
NRMSQT
Yes
Yes
Mosquito noise reduction
-
-
-
-
Yes
-
-
Yes
57
OVSCAN
Yes
Yes
Overscan setting
Yes
Yes
58
POWER
Yes
Yes
Power supply control
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
59
PRODCODE
-
Yes
Product name inquiry
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
60
RC
Yes
-
Remote control operation emulate
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
61
RGBGAIN
Yes
Yes
RGB gain adjustment
-
-
-
-
Yes
-
-
Yes
62
RGBOFFSET
Yes
Yes
RGB offset adjustment
-
-
-
-
Yes
-
-
Yes
63
ROMVER
-
Yes
Firmware version inquiry
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
64
SAT
Yes
Yes
Color saturation setting
-
-
-
-
Yes
-
-
Yes
65
SAVEIMGPROF
Yes
Yes
User memory creation/storage/deletion
-
-
-
-
Yes
-
-
Yes
66
SCRNASPECT
Yes
Yes
Screen aspect setting
-
-
-
-
Yes
-
-
Yes
67
SHARP
Yes
Yes
Sharpness setting
-
-
-
-
Yes
-
-
Yes
68
SIGMSG
Yes
Yes
Input status display
-
Yes
-
-
Yes
69
SIGNAL_INFO
-
Yes
Displayed signal information inquiry
-
-
-
-
Yes
-
-
Yes
70
SIGNALSTATUS
-
Yes
Signal detection inquiry
-
-
-
-
Yes
-
-
Yes
71
TEMP
-
Yes
Temperature sensor value inquiry
-
-
Yes
Yes
Yes
Yes
Yes
Yes
72
TPTN
Yes
Yes
Test pattern
-
-
-
-
Yes
-
-
Yes
73
ZSCLR
Yes
Yes
Zoom
Yes
Note: About "Power mode restriction"
Commands are executable only when the projector is in the mode indicated by "Yes." Meaning of each mode is as
follows:
Power mode restriction/LAN: Indicates whether the command coming through LAN is executable.
SL0: Standby mode, and the network function is turned off. When the network function is turned off, the command
is not executable if coming from LAN, in which case, this should never be “Yes”.
SL1: Standby mode, and the network standby setting is set to "Eco."
SL3: Standby mode, and the network standby setting is set to "Normal."
PM: Power management “lamp off” standby
ON: Normal projection status

WUX500ST User Commands
-12-
Power/RS-232C: Indicates whether the command coming through RS-232C is executable.
ST: Standby mode (includes SL0, SL1 and SL3 altogether, regardless of the network setting).

WUX500ST User Commands
-13-
5. Guide to Command Description
This section explains how commands are described.
The command descriptions have the format shown below.
EXAMPLE
Summary of the function
Format
Setting
Command
A command format when a command is sent to the projector to make a
setting for the function.
"-" is shown when there is no setting command.
Example) 6AXADJ=<6-axix adjustment parameter:
Response
A response format for the setting command.
"-" is shown when there is no setting command.
Example) i:OK
Reference
Command
A command format when a command is sent to the projector to refer to
the current setting, status and others for the function.
"-" is shown when there is no reference command.
Example) GET=6AXADJ
Response
A response format for a reference command.
"-" is shown when there is no reference command.
Example) g:6AXADJ=<6-axis adjustment parameter:
Note: See "Error list" for any response other than the above.
When parameters exist for the command, a list of parameter is inserted in this position.
Example)
<6-axis adjustment parameter:ID>
Parameter
Meaning
ON
Valid
OFF
Invalid

WUX500ST User Commands
-14-
Environment
This defines the environments that support the command (power supply state, input signal state).
The command is executable when the projector is in the mode indicated by "Yes" in the table of
corresponding command description page.
Power mode restriction
Input*11
LAN*1
WiFi*7
RS-232C*8
SL0
SL1
SL3
PM
ON
SL0
SL1
SL3
PM
ON
ST
PM
ON
D-RGB
A-RGB
COMP
HDMI
HDBT
LAN
USB
No
signal
*2
*3
*4
*5
*6
*2
*3
*4
*5
*6
*9
*5
*6
*10
*10
*10
*10
*10
*10
*10
*10
*1 Power mode restriction/LAN
Indicates whether the command coming through LAN is executable.
*2 SL0 Standby mode, and the network function is turned off.
When the network function is turned off, the command is not executable if coming
from LAN, in which case, this should never be “Yes”.
*3 SL1 Standby mode, and the network standby setting is set to "Eco."
*4 SL3 Standby mode, and the network standby setting is set to "Normal."
*5 PM Power management “lamp off” standby
*6 ON Normal projection status
*7 Power mode restriction/WiFi
Indicates whether the command coming through wireless LAN is executable.
Wireless LAN function is disabled in standby mode (SL 0, SL 1, SL 3). (Command
response does not return.)
Wireless LAN function is invalid when power management “lamp off” sets to standy.
(Command response does not return.)
*8 Power mode restriction/RS-232C
Indicates whether the command coming through RS-232C is executable.
*9 ST Standby mode (includes SL0, SL1 and SL3 altogether, regardless of the network
setting).
*10 Input Valid when the projector is in the input signal mode indicated by "Yes". Invalid when
the projector is in the input signal mode indicated by "No".
Remarks
Remarks about the command is inserted when necessary.
Example
Specific example of the command is inserted when necessary.

WUX500ST User Commands
-15-
6. Command Details
6AXADJ
6-axis color adjustment
Format
Setting
Command
6AXADJ=<6-axis adjustment parameter: ID>
Response
i:OK
Reference
Command
GET=6AXADJ
Response
g:6AXADJ=<6-axix adjustment parameter: ID>
Note: See "Error list" for any response other than the above.
<6-axis adjustment parameter:ID>
Parameter
Meaning
ON
Adjusted
OFF
Turned off
Environment
Power mode restriction
Input
LAN
WiFi
RS-232C
SL0
SL1
SL3
PM
ON
SL0
SL1
SL3
PM
ON
ST
PM
ON
D-RGB
A-RGB
COMP
HDMI
HDBT
LAN
USB
No
signal
No
No
No
No
Yes
No
No
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Remarks
(1) Use "6AXR - Y" command when this is set to "ON" and the corrected 6-axis values need to be
changed.
(2) This sets the currently selected input signal and image mode.
Example
(Control)
> 6AXADJ=ON
< i:OK
(Reference)
> GET=6AXADJ
< g:6AXADJ=ON
Note: '>' indicates a command; '<' indicates a response.

WUX500ST User Commands
-16-
6AXR
6-axis adjustment (red), hue/saturation/brightness
Format
Setting
Command
6AXR=<R hue:Number>,<R saturation:Number>, <R
brightness:Number>
Response
i:OK
Reference
Command
GET=6AXR
Response
g:6AXR=<R hue:Number>,<R saturation:Number>, <R
brightness:Number>
Note: See "Error list" for any response other than the above.
<R hue:Number> is within -20 to 20.
<R saturation:Number> is within -20 to 20.
<R brightness:Number> is within -20 to 20.
Environment
Power mode restriction
Input
LAN
WiFi
RS-232C
SL0
SL1
SL3
PM
ON
SL0
SL1
SL3
PM
ON
ST
PM
ON
D-RGB
A-RGB
COMP
HDMI
HDBT
LAN
USB
No
signal
No
No
No
No
Yes
No
No
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Remarks
(1) When 6-axis adjustment is turned on, these settings are shown over the displayed image. However,
the settings can be changed regardless of whether 6-axis adjustment is turned on or not.
(2) This sets the currently selected input signal and image mode.
Example
(Setting)
>6AXR=-8,5,3
< i:OK
(Reference)
> GET=6AXR
< g:6AXR=-8,5,3
Note: '>' indicates a command; '<' indicates a response.

WUX500ST User Commands
-17-
6AXG
6-axis adjustment (green), hue/saturation/brightness
Format
Setting
Command
6AXG=<G hue:Number>,<G saturation:Number>,<G
brightness:Number>
Response
i:OK
Reference
Command
GET=6AXG
Response
g:6AXG=<G hue:Number>,<G saturation:Number>,<G
brightness:Number>
Note: See "Error list" for any response other than the above.
<G hue:Number> is within -20 to 20.
<G saturation:Number> is within -20 to 20.
<G brightness:Number> is within -20 to 20.
Environment
Power mode restriction
Input
LAN
WiFi
RS-232C
SL0
SL1
SL3
PM
ON
SL0
SL1
SL3
PM
ON
ST
PM
ON
D-RGB
A-RGB
COMP
HDMI
HDBT
LAN
USB
No
signal
No
No
No
No
Yes
No
No
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Remarks
(1) When 6-axis adjustment is turned on, these settings are shown over the displayed image. However,
the settings can be changed regardless of whether 6-axis adjustment is turned on or not.
(2) This sets the currently selected input signal and image mode.
Example
(Setting)
>6AXG=-8,5,3
< i:OK
(Reference)
> GET=6AXG
< g:6AXG=-8,5,3
Note: '>' indicates a command; '<' indicates a response.