Canovate CAN-NBL-2100-J5K User manual

Performance Parameter
Color：black
Material：main body is zinc alloy +
stainless steel+ABS（electronic），
accessory is stainless steel
Lock boday size：170MM（L）X 42MM
（W）X 60MM（H）±5％
Lock body net weight：0.9Kg±5％
Rated operational voltage：DC12V
Input voltage range：DC10.8V－DC13.2V
Static working current：less than 150mA
1. Power supply and communication connection
2. Door sensor input connection
Connection Definition
Product Size
Operating Instructions
1st
2nd
3rd
4th
5th
red
black
Yellow
Green
White
DC12V power supply
Alarm output (OC output)
RS485 communicate port
+12v
GND
ARM(OC)
485A
485B
1st
2nd
purple
Black
DOOR.SW
GND
External “door
sensor” input port
3. Open lock input connection
1st
2nd
brown
Grey
Spare
lock close status
key open lock electronic control open lock
注意事项
1.Project password using method:
After install lock on cabinet box in the first time,
can input “1234” or “6666”or “8888”,then press
push button for open door and debug using, after
authorize user the project password invalid.
2.ID+ password open door method:
First authorize one user through software, for
example, user ID number is ”0000 0001”,
password is “1234”, open door first input user ID
number” 0001”(only need input the last four
digits), then input four digits password
“1234”,when blue light bright hand shank
bounce, rotate hand shank open lock.
3.Remote open door:
After confirm the software and cabinet lock
networking success, click “ remote open door” in
software, when the lock blue light bright then
press hand shank, when hand shank bounce
then rotate to left or right open lock.
4.Key open door:
Use match tools open the protection steel sheet
on the keyhole, then insert key rotate 90 degree,
after the hand shank bounce then can rotate
open lock.
Operation Method
CAN-NBL-2100-J5K
Series Intelligent Cabinet
Lock User Manual
NC
NC
rotation angle
8.5
70.1
21
90°
174
44 34.6
60
17.132.3
H=19
49.549.6
128.6
注意事项
1、Please read this user manual carefully
when install,to avoid making the cabinet
or device broken;
2、According this manual's installation
steps, using correctly tools to install,to
avoid causing injuries;
Notes

1、Connect to power supply after installation complete, blue light twinkle three times is
normal work;
2、Open central management software,click remote open door,blue light on,press PUSH ，
hand shank bounce,if timeout not open then will lock automatically;
3、Use authorized card swip on the hand shank read card area,blue light on,press PUSH ，
hand shank bounce,if timeout not open then will lock automatically, Unauthorized
card after swip card the red light twinkle two times;
4、Door switch input can set as normally open or normally close,after status change then
occur alarm,red light twinkle,and send alarm signals to the center.
Electricity test
1
Fig 1
Fig 2
change the “galvanized
washer”direction ，select left
open or right open
left open right open
support rods unit : millimeter
Fig 4
lock body
door frame
galvanized washer
washer
locking tabs
locking tabs's washer
locking tabs' screw
pressure plate's screw
pressure plate
Fig 3
Installation Instructions
Installation Steps
1、According to picture shown, the size
punching well the installation hole in fit
height of cabinet door （ suggest 1.1 m
or middle;
2、Unscrew lock's pressure plate's screw
and locking tabs' screw ,take the washer
and galvanized waher then tak the
pressure plate;
3、Put the lock's lead wire through the
hole thread from outside to inside of
the door Hold the lock on the door;
4、Put the lock's lead wire thread from
the biggest square hole of the pressing
plate（note Fig 3 direction）,then use
pressure plate fixed screw fix well;
5、Install galvanized washer、shim and
locking tabs,as Fig 2 shown select left
open or right open,use wrench fix well
the support rods（suggest as Fig4 add a
support rods,make the connection more
stronger;
6、According user manual or lock body's
connection definition connect well lead
wire;
7、Installation complete.
3、The device using 12V DC power supply，
please ensure connection correctly then
electricity use,to avoid making the device
broken.
www.canovate.com
Preparatory work：cross
screwdriver,Φ32 dowelling
jig，sander，10MM hexagonal-
wrench（adjustable wrench）.