Canvas TRIBECA 088-1689-8 User manual

TRIBECA TEAK BENCH
MODEL NO. 088-1689-8
ASSEMBLY INSTRUCTIONS
Toll-free: 1-888-670-6684
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
hh h

3
TABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS
MADE IN VIETNAM IMPORTED BY TRILEAF DISTRIBUTION TRIFEUIL TORONTO, CANADA M4S 2B8
Table of Contents 3
Important Safety Instructions 3
Parts List 5
Assembly 6
Cleaning and Maintenance 9
Technical Specifications 9
Warranty 10
IMPORTANT: Retain for future reference, and read carefully.
Warning! To reduce the risk of serious injury, read the following safety
instructions before assembling and using the table.
• This product is intended for domestic, outdoor use only.
• The product should be placed on flat, horizontal ground.
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange necessary manpower when assembling or moving the product.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Keep children and pets away while setting up the table.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• Repairing and replacing parts should of,be done by a qualified technician.
• Do not light any fires below, on top of, or near the product!
• Retain the original packaging to store the table.
Caution! Always keep children under close supervision while they are using or
around this product.
Never leave children unattended.

4 5
MODEL NO. 088-1689-8
ASSEMBLY PREPARATION PARTS LIST
Bench top - 1
1
Left bench leg - 1
2
Right bench leg - 1
3
Cross bar - 1
4
M8x25 mm bolt - 4
A
Washer - 12
B
Plastic cap - 4
C
7x35 mm screw - 8
D
Wrench - 1
E
Hex key - 1
F
2 people
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
1-888-670-6684
If you have questions regarding your product, require warranty
assistance, or have damaged or missing parts, please call our customer
service toll-free helpline. Contact us for assistance; we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning
assembly of product, make sure all parts are present. Compare parts with packaging contents
list. If any part is missing, or if you have any questions, contact the service centre at
1-888-670-6684 (toll-free).
Place all parts from the box in a cleared area and position them on the floor in front of you.
Remove all packing materials and place them back into the box. Do not dispose of the packing
materials until assembly is complete. Read each step carefully before beginning any assembly
and make sure you understand each step. If you are missing a part, please call our toll-free
number for assistance: 1-888-670-6684.
Needed for assembly:
CAUTION!
• Keep children away during assembly.
This product contains small parts which can be swallowed by children.
• Keep fingers away from places where they can be pinched or trapped.
• Do not attempt to assemble the bench if any parts are missing.
• Assemble this bench near the place it will be used.
• When assembling step 1 & 2, bolts and screws should be hand-tightened only.
Firmly tighten bolts with wrench and hex key in step 3.

6 7
MODEL NO. 088-1689-8
ASSEMBLY
ASSEMBLY
Step 3
Requires E, F
Use wrench Eto tighten bolts A, and also use hex key Fto tighten screws D.
E F
Step 2
Requires 1, B, D
Attach assembled legs to bench top 1with washers Band screws D.
D B
Step 1
Requires 2, 3, 4, A, B
A
Attach cross bar 4to left bench leg 2and right bench leg 3with bolts Aand
washers B.
B
A
A
B
B
4
2
3
4
1
43
2
B
B
1
D
D
E
F
NOTE:
Hand-tighten only the bolts and screws.
NOTE:
Firmly tighten all bolts and screws with wrench and hex key.

ASSEMBLY
8 9
MODEL NO. 088-1689-8
Step 5
Turn the bench right side up.
Adjust the feet to level bench if necessary.
Step 4
Requires C
C
Attach plastic caps Cto post bolts A.
CLEANING AND MAINTENANCETECHNICAL SPECIFICATIONS
Dimensions (L x W x H) 70 7/8 x 13 3/4 x 16 1/2"
180 x 35 x 42 cm
Product weight 47 lb 10 oz
21.6 kg
C
C
CAUTION!
• Check all screws and nuts periodically for tightness, tightening them
again as required.
• When assembling step 1 & 2, hand-tighten only the bolts & screws.
Firmly tighten all bolts & screws with wrench and hex key in step 3.
• Do not use bleach, acid, or other abrasive cleaners on the surface of the bench.
• Use only a wet cloth to clean the top.
• Teak is renowned for its rich golden-brown appearance but also for its classic
aging appearance after exposure to the elements of weather and time. Over
time teak will naturally change to a mature, silver-grey patina. This generally
begins to happen after 4-5 months of no treatment. If left for 2 years without
treatment, the silver-grey patina will change to a dark grey/green colour.
Many connoisseurs of teak furniture prefer this mature silver-grey patina, but if
the original golden-brown appearance is preferred, we recommend treating
your furniture using a teakwood sealer oil.