Canyon 91-705 User manual

CANYON FURNITURE COMPANY
1.- USE THE LONG END OF THE ALLEN WRENCH TO FASTEN BOLTS LOOSELY AND QUICKLY.
2.- USE THE SHORT END OF THE ALLEN WRENCH FOR FINAL TIGHTENING.
TIPS : SEE ILLUSTRATION BELOW
(91/92/93-705 ) CHARCOAL COLLECTION STUDENT BUNK BED ASSEMBLY INSTRUCTIONS
READ ALL THE INSTRUCTIONS AND IDENTIFY ALL COMPONENTS AND CHOOSE YOUR CONFIGURATION AND BE SURE YOU HAVE ALL PARTS
TWO PEOPLE ARE NEEDED TO ASSEMBLE.
THANK YOU FOR YOUR PURCHASE !
CONFIGURATION TYPE # 2
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUESTPLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
CONFIGURATION TYPE # 1CONFIGURATION TYPE # 1
DO NOT COMPLETELY TIGHTEN ALL BOLTS UNTIL ALL COMPONENTS ARE CONNECTED.
TOOLS NEEDED
PHILIPS HEADSCREWDRIVER (NOT INCLUDED)
5MM ALLEN WRENCH (INCLUDED)
TIPS # 1
TO ASSEMBLE THIS BUNK BED REQUIRES
TWO PERSONS
WARNING:
THE BED SLATS WILL NO SUPPORT A
MATTRESS ALONE,A SLAT PACK OR A
BUNKIE BOARD IS REQUIRED FOR
PROPER SAFETY.
( NOT INCLUDED )
92-705 LOFT BED END
92-706 BUNK BED END
92-711 5 DRW STUDENT LOFT CHEST
92-730 6 PCS SIDE RAILS
92-709 FULL BED
92-645 4 PCS SLAT PACK 3/3
92-646 4 PCS SLAT PACK 4/6
92-705 LOFT BED END
92-706 BUNK BED END
92-710 3 DRW STUDENT LOFT DESK
92-730 6 PCS SIDE RAILS
92-709 FULL BED
92-645 4 PCS SLAT PACK 3/3
92-646 4 PCS SLAT PACK 4/6
92-705 LOFT BED END
92-706 BUNK BED END
92-711 5 DRW STUDENT LOFT CHEST
92-730 6 PCS SIDE RAILS
92-709 FULL BED
92-601 FOLDING DESK
92-645 4 PCS SLAT PACK 3/3
92-646 4 PCS SLAT PACK 4/6
92-705 LOFT BED END ( 2 BOXES )
92-710 3 DRW STUDENT LOFT DESK
92-711 5 DRW STUDENT LOFT CHEST
92-730 6 PCS SIDE RAILS
92-707 TWIN BED
92-720 LADDER
92-645 4 PCS SLAT PACK 3/3 ( 2 BOXES )
92-705 LOFT BED END ( 2 BOXES )
92-711 5 DRW STUDENT LOFT CHEST ( 2BOXES )
92-730 6 PCS SIDE RAILS
92-707 TWIN BED
92-720 LADDER
92-601 FOLDING DESK
92-645 4 PCS SLAT PACK 3/3 ( 2 BOXES )
TIPS # 2
REV 01 14/04/2016 PAGE 1 OF 5 KIS01112

CANYON FURNITURE COMPANY
A.- (1) HEADBOARD
B.- (1) 3 DRW STUDENT LOFT DESK
C.- (1) 5 DRW STUDENT LOFT CHEST M.- (1) CASTER BED HEADBOARD
D.- (1) LOFT BED END
E.- (2) METAL DOWEL PINS J.- (6) 1 1/4" SCREW
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
H.- (24) 5/16" X 4" HEX TAP BOLTS
I.- (24) 5/8" CROSS DOWEL NUTS
J.- (24) 5/16" FLAT WASHERS
K.- (1) 5MM ALLEN WRENCH
L.- (4) 39" SLATS
M.- (8) 1 1/4" SCREWS
N.- (1) HEADBOARD Q.- (4) 54" SLATS
O.- (1) FOOTBOARD
M.- (8) 1 1/4" SCREWS
P.- (4) CASTER SOCKETS
1.- ASSEMBLE TWIN LOFT BUNK BED, USING ONE HEADBOARD ( A),ONE LOFT BED END ( D),TWO SIDE RAILS ( F),TWO GUARDRAILS ( G), 3 DRW STUDENT DESK (B) OR 5 DRW STUDENT
CHEST(C).
2.- TAKE 3 DRAWER STUDENT DESK (B) OR 5 DRAWER STUDENT CHEST (C), THEN PLACED THEM IN DESIRED POSITION IN THE ROOM, (PLACE FRONT FACE OF DESK OUTWARDS)
3.- INSERT ONE METAL DOWEL PIN (E) IN EACH OUTSIDE CORNER OF 3 DRW LOFT DESK OR 5 DRW LOFT CHEST, TAKE THE LOFT BED END, AND PLACE IT ON TOP OF DESK OR CHEST
ALIGNING THE METAL DOWEL PIN WITH EACH PRE - DRILLED HOLE IN EVERY END OF THE LOFT BED END UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLE OF THE BED, SEE FIG.9
4.- INSERT TWO CROSS DOWEL NUTS (I) INTO THE SIDE RAIL AND GUARDRAILS HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.10
5.- ATTACH TWO SIDE RAILS & TWO GUARD RAILS TO HEADBOARD&LOFT BED END, INSERTING TWO HEX TAP BOLTS (H) TWO WASHERS (J) INTO HEADBOARD&LOFT BED END HOLES,
USE THE 5MM ALLEN WRENCH (K) TO TIGHTEN BOTH HEX TAP BOLTS,
(DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER)
, SEE FIG.11
6.- REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
7.- PLACE FOUR SLATS (L) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH HEADBOARD&LOFT BED ENDS,PUSH THE SLAT AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE
MIDDLE AT EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (M), SEE FIG.12
HARDWARE PACK (HPK00016)
4 PCS SLAT PACK 4/6 BOX ( 92-646 ) FIG.8
LIST OF CONTENTS
K.- (1) 3 DRAWER NIGHT STAND
3 DRAWER STUDENT LOFT DESK BOX ( 92-710 ) FIG.2 OR
CHARCOAL COLLECTION
HARDWARE PACK (HPK00095)
TWIN UPPER BUNK BED BOX ( 92-705 ) FIG.4
HARDWARE PACK (HPK00093)
3 DRAWER NIGHT STAND BOX ( 90-503 )TWIN LOFT BUNK BED END BOX ( 92-706 ) FIG.1
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 1
L.- (1) DESK TOP
5 DRAWER STUDENT LOFT CHEST BOX ( 92-711 ) FIG.3 CASTER TWIN BED BOX ( 90-707,90-709 )
O.- (4) METAL CASTER SOCKET
N.- (1) CASTER BED FOOTBOARD
4 PCS SLAT PACK 3/3 BOX ( 92-645 ) FIG.6
HARDWARE PACK (HPK00094)
DESK TOP BOX ( 90-602 )
HARDWARE PACK (HPK00016)
FULL BED BOX ( 92-709 ) FIG.7
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.56 PCS SIDE RAILS BOX ( 92-730 ) FIG.5
A
FIG.1 FIG.2
BC
FIG.3
D
E
FIG.4
FG
H I
J
K
FIG.5
L
M
FIG.6
NO
P
FIG.7
Q
FIG.8
FIG.9
YES,
HORIZONTAL GROOVE
FIG.10
FIG.11
FIG.12
FIG. A
NO
REV 01 14/04/2016 PAGE 2 OF 5 KIS01112

CANYON FURNITURE COMPANY
CHARCOAL COLLECTION
A.- (1) LOFT BED END
B.- (2) METAL DOWEL PINS
C.- (1) 3 DRW STUDENT LOFT DESK
D.- (1) 5 DRW STUDENT LOFT CHEST
E.- (4) SIDE RAILS
F.- (2) GUARD RAILS
G.- (24) 5/16" X 4" HEX TAP BOLTS
H.- (24) 5/8" CROSS DOWEL NUTS
I.- (24) 5/16" FLAT WASHERS
J.- (1) 5MM ALLEN WRENCH
K.- (1) LADDER
L.- (2) METAL HOOK BRACKETS
M.- (6) 1" SCREWS
N.- (1) HEADBOARD
O.- (1) FOOTBOARD
P.- (4) CASTER SOCKETS
Q.- (4) 39'' SLATS
R.- (8) 1 1/4" SCREWS
1.- ASSEMBLE TWIN UPPER BUNK BED, USING TWO LOFT BED ENDS (A), TWO SIDE RAILS (E), AND TWO GUARDRAILS (F).
2.- INSERT TWO CROSS DOWEL NUTS (H) INTO THE SIDE RAIL AND GUARDRAILS HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.8
3.- ATTACH TWO SIDE RAILS (E) AND TWO GUARD RAILS (F) TO BOTH LOFT BED ENDS (A), INSERTING TWO HEX TAP BOLTS (G) TWO WASHERS (I) INTO LOFT BED END HOLES, USE THE
5MM ALLEN WRENCH (J) TO TIGHTEN BOTH HEX TAP BOLTS
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER )
, SEE FIG.9
4.- REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
5.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS, ONE SLAT IN BOTH LOFT BED ENDS, PUSH THE SLAT AGAINST THE BED END POST ( FIG.A ) AND TWO SLATS IN THE MIDDLE AT
EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (R), SEE FIG.10
LIST OF CONTENTS
HARDWARE PACK
(HPK00095)
3 DRW STUDENT LOFT DESK BOX ( 92-710 ) FIG.2
LADDER BOX (92-720) FIG.5
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.4
HARDWARE PACK
(HPK00093)
5 DRW STUDENT LOFT CHEST BOX ( 92-711 ) FIG.3
HARDWARE PACK
(HPK00008)
TWIN BED BOX ( 92-707 ) FIG.6
4 PCS SLAT PACK 3/3 BOX ( 92-645 ) FIG.7 ( 2 BOXES )
HARDWARE PACK
(HPK00016)
TWIN UPPER BUNK BED BOX ( 92-705 ) FIG.1 ( 2 BOXES )
HARDWARE PACK
(HPK00094)
TOOLS NEEDED
PHILLIPS HEADSCREWDRIVER ( NOT INCLUDED )
5MM ALLEN WRENCH ( INCLUDED )
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2
FIG.2
D
FIG.5
C
A
B
FIG.1
EF
GH
I
J
N
O
FIG.4
P
Q
R
FIG.6
MAKE SURE ALL BOLTS ARE TIGHTENED
COMPLETELY
FIG.7
YES,
HORIZONTAL GROOVE NO
FIG.8
FIG.9
FIG.10
FIG.A
K
L
M
FIG.3
REV 01 14/04/2016 PAGE 3 OF 5 KIS01112

CANYON FURNITURE COMPANY
6.- TAKE 3 DRW STUDENT LOFT DESK (C) AND 5 DRW STUDENT LOFT CHEST (D), PLACED THEM IN DESIRED POSITION IN THE ROOM,
(PLACE FRONT FACE OF DESK OUTWARDS).
7.- INSERT ONE METAL DOWEL PIN (B) IN EACH OUTSIDE CORNER OF 3 DRW LOFT DESK AND 5 DRW LOFT CHEST, SEE FIG.11
THE BED UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLES OF THE BED, SEE FIG.12
HOOKS ON TOP GUARDRAIL AND SECURE THE LADDER, AS SHOWN IN
CONFIGURATION TYPE # 2
CASTER TWIN BED BOX ( 90-707,90-709 )
J.- (6) 1 1/4" SCREW
1.- ASSEMBLE ROLL AWAY BED, USING ONE HEADBOARD (N), ONE FOOTBOARD (O) AND TWO SIDE RAILS (F).
2.- INSERT TWO CROSS DOWEL NUTS (I) INTO THE SIDE RAIL HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.1
3.- ATTACH THE HDBD&FTBD INTO THE SIDE RAILS, INSERTING TWO HEX TAP BOLTS ( H) AND TWO WASHERS ( J) INTO THE HDBD&FTBD HOLES, USE THE 5MM ALLEN WRENCH (K) TO
TIGHTEN BOLTS UNTIL SECURE, SEE FIG.2
4.- PLACE FOUR SLATS ( L,Q ) ON SIDE RAIL CLEATS, ONE SLAT IN BOTH HDBD&FTBD ENDS, PUSH THE SLAT AGAINST THE BED END POST ( FIG.A ) AND TWO SLATS IN THE MIDDLE AT
EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (M), SEE FIG.3
5.- INSERT THE CASTER SOCKETS (P) INTO BOTTOM CORNERS OF THE HEADBOARD&FOOTBOARD, SEE FIG.B
6.- ROLL THE BUNK BED AND PLACE IT BETWEEN 3 DRAWER STUDENT DESK AND LOFT BUNK BED AS SHOWN IN
CONFIGURATION TYPE # 1 AND TYPE # 2
O.- (4) METAL CASTER SOCKET
N.- (1) CASTER BED FOOTBOARD
M.- (1) CASTER BED HEADBOARD
8.- TAKE THE ASSEMBLED TWIN UPPER BUNK BED, PLACE IT ON TOP OF BOTH CASES, ALIGNING THE METAL DOWEL PINS WITH EACH PRE- DRILLED HOLE IN EVERY CORNER OF
9.- ALIGN THE PRE - DRILLED HOLES IN LONG PART OF METAL HOOKS BRACKETS (L) WITH THE PRE-DRILLED HOLES IN THE LADDER (K), SECURE WITH 1" SCREWS (M) USING PHILLIP
HEADSCREWDRIVER ( NOT INCLUDED ),SEE FIG.C AND HOOK THE LADDER IN THE PROPER POSITION, ADJUST AND ALIGN THE PRE-DRILLED HOLES IN THE SHORT PART OF METAL
ROLL AWAY CASTER BED ASSEMBLY INSTRUCTIONS
K.- (1) 3 DRAWER NIGHT STAND
YES,
HORIZONTAL GROOVE
FIG.1
NO
FIG.2
FIG.3
FIG.B
FIG.11
FIG.12
1 1/4 " SCREWS
SIDE RAIL
LADDER METAL HOOKS
LADDER
GUARD RAIL
HEADBOARD&FOOTBOARD
POSITION LADDER
FIG.C
REV 01 14/04/2016 PAGE 4 OF 5 KIS01112

CANYON FURNITURE COMPANY
1.- FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
2.- ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
3.- SURFACE OF MATTRESS MUST BE AT LEAST 5 IN BELOW THE UPPER EDGE OF GUARDRAILS.
4.- DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
5.- PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
6.- PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL,LADDER AND OTHER COMPONENTS ARE IN THEIR PROPER POSITION,FREE FROM DAMAGE,AND THAT ALL CONNECTORS
ARE TIGHT.
7.- DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED.
8.- ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
9.- DO NOT USE SUBSTITUTE PARTS. CONTACT THE MANUFACTURER OR DEALER FOR REPLACEMENT PARTS.
10.- USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD USING THE UPPER BUNK.
11 .- IF THE BUNK BED WILL BE PLACED NEXT TO THE WALL THE GUARDRAIL THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT, ENTRAPMENT
BETWEEN THE BED AND THE WALL.
12.- ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK.
13.- THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
14.- STRANGULATION HAZARD. NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED, FOR EXAMPLE, BUT
NOT LIMITED TO HOOKS, BELTS AND JUMP ROPES.
15.- KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THE UPPER AND LOWER BUNK BED IS DESIGNED TO USE ONLY MATTRESS WHICH IS 74" TO 75" LONG AND 37 1/2"TO 38 1/2" WIDE FOR TWIN BED.
THE UPPER AND LOWER BUNK BED IS DESIGNED TO USE ONLY MATTRESS WHICH IS
74"
TO
75"
LONG AND
57 1/2"
TO
58 1/2"
WIDE FOR
FULL BED.
THE BUNKIE BOARD IS REQUIRED TO 37 1/2" WIDE X 74" LONG FOR TWIN BED AND 57 1/2" WIDE X 74" LONG FOR FULL BED.
NOTE: ENSURE THICKNESS OF MATTRESS AND FOUNDATION COMBINED DOES NOT EXCEED 8 1/2" AND MATTRESS IS AT LEAST 5" BELOW UPPER EDGE OF GUARDRAILS.
SIZE OF MATTRESS AND FOUNDATION
REPLACEMENT PARTS, INCLUDING ADDITIONAL GUARDRAILS, MAY BE OBTAINED FROM ANY OF OUR CANYON FURNITURE COMPANY DEALERS.
REPLACEMENT PARTS
SAFETY WARNINGSSAFETY WARNINGS
REV 01 14/04/2016 PAGE 5 OF 5 KIS01112