Caple CM110SS User manual

Sense Combination Microwave
Instruction Manual
Contact Caple on 0117 938 7420 for spare parts or www.caple.co.uk
CM110SS

2Instruction manual CM110SS2Please keep this instruction manual for future reference
CONTENTS
Warnings 3
Environmental Protection 10
Warranty 10
Installation 11
Dimensions 12
Electronic Connection 13
Control Panel 14
Display 15
Accessories 16
Operation 17
Microwave Oven Functions 19
Auto Cooking 21
Defrost Time Table 23
Demo Mode 24
Care and Maintenance 25
Removing the Oven Door 26
Troubleshooting 27
Technical Data 27
Caple Contact Details 29

3
Please keep this instruction manual for future reference Instruction manual CM110SS
GENERAL WARNINGS:
Read carefully all the instructions contained in this
manual. It provides you with important information
regarding the safe installation, use and maintenance of
the appliance as well as useful advice for getting the best
out of your microwave oven. Keep this booklet in a safe
place for future reference. After removing the packing,
check that the appliance is not damaged in any way.
Be careful not to leave the packing materials (plastic
sheeting, expanded polystyrene etc.) where children can
get at them, as they can be dangerous.
IMPORTANT:
Do not use the oven door handle to move the appliance,
such as to remove it from the packaging.
ATTENTION:
The microwave oven is an appliance which, for its nature,
becomes hot during use, especially the glass door.
It is therefore a good rule that children do not approach
the microwave oven when it is functioning, particularly
when the grill is in use.
Before you use the microwave oven for the first time, heat
the empty oven at max. temperature for 1 hour, removing
any unpleasant smells and smoke caused by working
residues and thermal insulation. Make sure you do this in

4Instruction manual CM110SS4Please keep this instruction manual for future reference
a well ventilated area.
Never roast or bake on the oven base.
This product is not designed for commercial use, it is a
household appliance only. It is not intended to be used in:
-Staff kitchen areas in shops, offices and other working
environments.
-Bed and breakfast type environments.
The electrical system of this appliance may be used safely
only when it is correctly connected to an efficient earthing
system in compliance with the safety standards currently
in effect.
The manufacturer will not be held liable for any damages
that might arise out of incorrect or improper use of
the appliance.
The following items are potentially dangerous, and
therefore, appropriate measures must be taken to prevent
children and the disabled from coming into contact
with them:
-Controls and the appliance in general;
-Packaging (bags, polystyrene, nails, etc.);
-The appliance immediately after use of the oven or grill
due to the heat generated;
-The appliance when no longer in use (potentially
dangerous parts must be made safe).

5
Please keep this instruction manual for future reference Instruction manual CM110SS
WARNING:
-Accessible parts will become hot when in use. To avoid
burns and scalds children should be kept away.
-During use the appliance becomes hot, care should be
taken to avoid touching heating elements inside the
oven.
-If the door or door seals are damaged, the oven must
not be operated until it has been repaired by a Caple
approved engineer.
-It is hazardous for anyone other than a competent
person to carry out any service or repair operation that
involves the removal of a cover which gives protection
against exposure to microwave energy.
-Liquids and other foods must not be heated in sealed
containers since they are liable to explode.
-Only use utensils that are suitable for use in
microwave ovens.
-When heating food in plastic or paper containers, keep
an eye on the oven due to the possibility of ignition.
-The microwave oven is intended for heating food and
beverages. Drying of food or clothing and heating of
warming pads, slippers, sponges, damp cloth and similar
may lead to risk of injury, ignition or fire.
-The oven should be cleaned regularly and any food
deposits removed.
-Failure to maintain the oven in a clean condition could
lead to deterioration of the surface that could adversely
affect the life of the appliance and possibly result in a
hazardous situation.

6Instruction manual CM110SS6Please keep this instruction manual for future reference
WARNING:
To reduce the risk of burns, electric shock, fire, injury to
persons or exposure to excessive microwave energy:
-Make sure that all the packing materials are removed
from the inside of the door.
-This microwave oven must be placed on a flat, stable
surface to hold its weight and the heaviest food likely to
be cooked in the oven.
-Do not place the microwave oven where heat, moisture,
or high humidity are generated, or near combustible
materials.
-Do not operate the microwave oven when empty.
- Do not operate this appliance if it has a damaged cord or
plug, if it is not working properly or if it has been damaged
or dropped. If the supply cord is damaged, it must be
replaced by Caple or an approved engineer in order to
avoid a hazard.
-Microwave heating of liquids can result in delayed
eruptive boiling, therefore care has to be taken when
handling the container.
-Do not fry food in the microwave oven. Hot oil can
damage oven parts and utensils and even result in
skin burns.
-Eggs in their shell and whole hard-boiled eggs should
not be heated in microwave ovens since they may
explode even after microwave heating has ended.
-Pierce foods with heavy skins such as potatoes, whole
squashes, apples and chestnuts before cooking.

7
Please keep this instruction manual for future reference Instruction manual CM110SS
-The contents of feeding bottles and baby jars should be
stirred or shaken and the temperature should be checked
before serving in order to avoid burns.
-Utensils should be checked to ensure that they are
suitable for use in microwave oven.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless the have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
-Children should be supervised to ensure that they do not
play with the appliance.
-When heating food in plastic or paper containers, check
the oven frequently for the possibility of ignition.
-Remove wire ties from paper or plastic bags before
placing bag in oven.
-If smoke is observed. Switch off or unplug the appliance
and keep the door closed in order to stifle any flames.
-Do not leave paper products, cooking utensils or food in
the cavity when not in use.
-WARNING: Check the oven for any damage, such as
misaligned or bent door, damaged door seals and
sealing surface, broken or loose door hinges and latches
and dents inside the cavity or on the door. If there is any
damage, do not operate the oven and contact Caple
service immediately.

8Instruction manual CM110SS8Please keep this instruction manual for future reference
-WARNING: Liquid or other food must not be heated in
sealed containers since they are liable to explode.
-WARNING: It is hazardous for anyone other a trained
person to carry out any service or repair operation which
involves the removal of any cover which gives protection
against exposure to microwave energy.

9
Please keep this instruction manual for future reference Instruction manual CM110SS
WARNING
The appliance and its accessible parts become hot
during use.
Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless
continuously supervised
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be
made by children without supervision.
During use the appliance becomes hot. Care should be
taken to avoid touching heating elements inside the oven.
WARNING: Accessible parts may become hot during use.
Young children should be kept away.
ATTENTION:
-Before use, remove all plastic films protecting some parts
of the appliance (fascia - panel, parts in stainless
steel, etc)
-Do not use the appliance to heat a room.
-When the appliance is not in use, we recommend you
turn it off, isolate it from the electrical supply.

10 Instruction manual CM110SS10 Please keep this instruction manual for future reference
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. The symbol on the product indicates
that this product may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. Disposal must
be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local council, your household waste disposal service or the retailer where you
purchased the product.
CE DECLARATIONS OF CONFORMITY
This appliance has been designed, constructed and marketed in compliance with safety
requirements in force. This appliance has been manufactured to the strictest standards and
complies with all applicable legislation.
WARRANTY
Your new appliance is covered by warranty. The warranty card is enclosed - if it is missing, you
must provide the following information to your retailer in order to receive a replacement: date
of purchase, model and serial number (placed on the inside of the appliance storage drawer).
Registration can also be completed online by visiting www.caple.co.uk.
Ensure you keep your warranty card safe, you may need to show it to Caple Service together with
proof of purchase.
If you fail to show your warranty card you will incur all repair charges.
Spare parts are only available from Caple Service and spare parts authorised centres.

11
Please keep this instruction manual for future reference Instruction manual CM110SS
DIMENSIONS
548mm 22mm
8.6mm
454mm
min. 550mm
565mm
595mm
450mm
70mm
Ventilation Slot
70mm
23mm
Instruction manual12
540mm
593mm
578mm
589mm
min 550mm
560mm
555mm
25mm
5mm
595mm
70mm
20mm
Dimensions
116mm
INSTALLATION
IMPORTANT:
ISOLATE YOUROVEN FROMTHE ELECTRICAL SUPPLY BEFORE
PERFORMING INSTALLATION OR MAINTENANCE.
FITTING THE APPLIANCE
Fit the applianceinto its surround(beneath a
worktop or above another appliance in a tall
housing) by inserting screws and plastic covers
into the holes (A - fig.3) that can be seen in
the frame of the oven when the door is open.
For the most efficient
air circulation, the
oven
should be fitted
according to the
dimensions
shown in fig.1.
The rear panel of the
cabinet must be
removed so that air
can circulate freely. The
panel to which the
ovenis
fitted should havea
gap of at least 70 mm
at the rear for
ventilation (fig.4 &
fig.5).
589mm
70mm
min 550mm
560mm
70mm
540mm
593mm
578mm
555mm
25mm
5mm
595mm
20mm
116mm
only
materialsincorrect
Fitting the appliance
a
in
aircan
a(fig.4&fig.5).
NOTE : where ovens are to be matched with hobs, it is essential
to follow the instructions contained in the manual supplied with
the hob
Plastic cover
Fig.3
Oven dimensions
Fig.2
Fig.1
INSTALLATION
IMPORTANT:
ISOLATE YOUR MICROWAVE OVEN FROM THE ELECTRICAL SUPPLY BEFORE PERFORMING
INSTALLATION OR MAINTENANCE.
Installation should be carried out according to the instructions by a professionally qualified
person only.
The manufacturer declines all responsibility for any damage to persons, animals or materials
due to incorrect installation.
FITTING THE APPLIANCE
Fit the appliance into its surround (beneath a
worktop or above another appliance in a tall
housing) by inserting screws and plastic covers into
the 4 holes (A - fig.3) that can be seen in the frame
of the oven when the door is open.
For the most efficient air circulation,
the microwave oven should be fitted
according to the dimensions shown
in fig.1.
Fig1

12 Instruction manual CM110SS12 Please keep this instruction manual for future reference
569mm
595mm
547mm
8.6mm
8mm
2.8mm
22mm
453.6mm
116mm
26.4mm 26.4mm
See below for full dimensional drawings of your microwave oven to help
with installation.
For a built-in microwave oven to work well, the cabinet must be the right type.
The panels of the adjoining furniture should be heat resistant. Particularly when the adjoining
furniture is made of veneered wood, the adhesives should be able to withstand a temperature
of 120ºC. Plastic materials or adhesive which cannot withstand this temperature may become
deformed or unstuck.
To comply with safety regulations, once the appliance has been fitted it should not be possible to
make contact with the electrical parts.
All parts which offer protection should be fixed in such a way that they cannot be removed
without the use of a tool.
MICROWAVE OVEN DIMENSIONS
Instruction manual
Please keep this instruction manual for future reference
13
See below for full dimensional drawings of your microwave oven to help with
installation.
For a built-in microwaveoven to work well thecabinetmust be of the right type.
The panels of the adjoining furniture should be heatresistant. Particularly when
the adjoiningfurniture is madeof veneered wood, the adhesives should be able
to withstand a temperature of 120ºC. Plastic materials oradhesive which cannot
withstand this temperature may become deformed orunstuck.
To comply withsafety regulations, once the appliance has been fitted it should
not be possible to make contact withthe electrical parts.
All parts which offer protectionshould be fixed in such a way that they cannot be
removedwithout the use of a tool.
MICROWAVE OVEN DIMENSIONS
Fig.4 Fig.5
70
70
70
The rear panel of the cabinet
must be removed so that air can
circulate freely. The panel to which
the microwave oven is fitted
should have a gap of at least 70
mm at the rear for ventilation
(fig.4 & fig.5).

13
Please keep this instruction manual for future reference Instruction manual CM110SS
ELECTRICAL CONNECTION
WARNING:
This appliance must be earthed.
Check that the power rating of the mains supply is suitable for the maximum power of the
appliance as indicated on the rating label.
The fuse rating for this appliance is 13amp.
The appliance is supplied with a mains lead it should be “Hard wired” as follows:
»The “yellow/green” earth wire, which must be connected to a terminal, and has to be about
10mm longer than the other wire.
»The neutral wire has to be connected to the terminal marked with a letter N.
»Mains connection can also be made by fitting a double pole switch with a minimum gap
between the contacts of 3mm, proportionate to the load and complying with the regulations
in force.
THE YELLOW/GREEN EARTH WIRE SHOULD NOT BE CONTROLLED BY THE SWITCH.
When a double pole switch is used for mains supply connection it should be easily accessed, once
the appliance is in position.
IMPORTANT:
The mains supply cable should be positioned so that it is never subjected to temperatures which
are more than 50ºC above ambient temperature.
The electrical safety of the appliance can only be guaranteed when it has been correctly connected
to a properly earthed mains electrical supply, as laid down in the current regulations for
electrical safety.
The manufacturer cannot be held responsible for any damage to persons or objects due to lack of
an earth connection.
The ovens are designed to operate with a mono-phase alternating current of
220-240V, 50Hz.
BEFORE THE INSTALLATION OF THE APPLIANCE, CHECK THE SPECIFICATIONS ON THE
RATING LABEL.

14 Instruction manual CM110SS14 Please keep this instruction manual for future reference
1. Power
2. Programme
3. Timer
4. Temperature ºC
/ Power (watts) /
Weight (grams)
5. Auto cooking
6. Up
7. Down
8. Select
9. Light / Child lock
10. Start / Pause
CONTROL PANEL
AUTO
˚C / W/ g
1. Power (on/off)
2. Programme
3. Timer
4. Temperature / Power(wattage) / Weight(grams)
5. Auto cooking
6. Up
7. Down
8. Select
9. Light / Child lock
10. Start/pause
1. Programme / Function
2. Microwave
3. Defrost
4. Auto cooking
5. Temperature / power / weight
6. Timer
7. Time
Number display as per below
8. Child lock
9. Light
10. Alarm
11. End time
12. Duration time
13. Temperature/time display
DISPLAY
12
34
5
67
89
10
CONTROL PANEL

15
Please keep this instruction manual for future reference Instruction manual CM110SS
DISPLAY
1. Programme / Function
2. Microwave
3. Defrost
4. Auto cooking
5. Temperature / Power /
Weight
6. Timer
7. Time
8. Child lock
9. Light
10. Alarm
11. End time
12. Duration time
13. Temperature / Time Display
14. Heating indicator
CONTROL PANEL
AUTO
˚C / W/ g
1. Power (on/off)
2. Programme
3. Timer
4. Temperature / Power(wattage) / Weight(grams)
5. Auto cooking
6. Up
7. Down
8. Select
9. Light / Child lock
10. Start/pause
1. Programme / Function
2. Microwave
3. Defrost
4. Auto cooking
5. Temperature / power / weight
6. Timer
7. Time Number display as per below
8. Child lock
9. Light
10. Alarm
11. End time
12. Duration time
13. Temperature/time display
DISPLAY
1
2
34567
8
9
10
11
12 13
14
NOTE:
The Heating indicator will turn on to show the oven is heating up. When the oven reaches the set
temperature this indicator will turn off.
The same indicator will turn back on at some points during cooking when the oven falls slightly
below the set temperature.
This is normal, and will turn off again when the set temperature is regained.

16 Instruction manual CM110SS16 Please keep this instruction manual for future reference
ACCESSORIES
Wire shelf (Fig.1)
The wire shelf allows you to brown or grill food. The shelf should not, under any
circumstances, be used with other metal cookware when using any microwave
function. However, you can heat food in an aluminum tray providing it is separated
from the shelf by a plate.
Enameled tray (Fig.2)
The enameled tray allows you to cook foods on normal fan heat, conventional
cooking, and grilling functions.
WARNING: Do not use the enameled tray with any microwave function. This could
damage the enamel tray or even your microwave oven. The enameled tray is for
normal convection/Fan cooking or grilling only.
The side shelf supports (Fig.3)
2 hook-on shelf supports allow you to use the accessories on three levels.
Three cooking levels are available, depending on the method used and the type of
food.
With the Grill or Grill + Microwave setting, the accessories (shelf or tray) are placed
on the first level for thick foods like roasts and on the third level for thinner foods
like sausages.
In normal cooking modes, or microwave functions, the shelf should be used on the
first or second levels depending on the item(s) being cooked.
NOTE: Always remove the enameled tray when using microwave functions, as this
could damage the oven.
Fig.1
Fig.2
Fig.3
Fig. 1
ACCESSORIES
Wire shelf (Fig.1)
The wire shelf allows you to brown or grill food. The shelf should not, under any
circumstances, be used with other metal cookware when using any microwave
function. However, you can heat food in an aluminum tray providing it is separated
from the shelf by a plate.
Enameled tray (Fig.2)
The enameled tray allows you to cook foods on normal fan heat, conventional
cooking, and grilling functions.
WARNING: Do not use the enameled tray with any microwave function. This could
damage the enamel tray or even your microwave oven. The enameled tray is for
normal convection/Fan cooking or grilling only.
The side shelf supports (Fig.3)
2 hook-on shelf supports allow you to use the accessories on three levels.
Three cooking levels are available, depending on the method used and the type of
food.
With the Grill or Grill + Microwave setting, the accessories (shelf or tray) are placed
on the first level for thick foods like roasts and on the third level for thinner foods
like sausages.
In normal cooking modes, or microwave functions, the shelf should be used on the
first or second levels depending on the item(s) being cooked.
NOTE: Always remove the enameled tray when using microwave functions, as this
could damage the oven.
Fig.1
Fig.2
Fig.3
Fig. 2
ACCESSORIES
Wire shelf (Fig.1)
The wire shelf allows you to brown or grill food. The shelf should not, under any
circumstances, be used with other metal cookware when using any microwave
function. However, you can heat food in an aluminum tray providing it is separated
from the shelf by a plate.
Enameled tray (Fig.2)
The enameled tray allows you to cook foods on normal fan heat, conventional
cooking, and grilling functions.
WARNING: Do not use the enameled tray with any microwave function. This could
damage the enamel tray or even your microwave oven. The enameled tray is for
normal convection/Fan cooking or grilling only.
The side shelf supports (Fig.3)
2 hook-on shelf supports allow you to use the accessories on three levels.
Three cooking levels are available, depending on the method used and the type of
food.
With the Grill or Grill + Microwave setting, the accessories (shelf or tray) are placed
on the first level for thick foods like roasts and on the third level for thinner foods
like sausages.
In normal cooking modes, or microwave functions, the shelf should be used on the
first or second levels depending on the item(s) being cooked.
NOTE: Always remove the enameled tray when using microwave functions, as this
could damage the oven.
Fig.1
Fig.2
Fig.3
Fig. 3
Fig. 4
WIRE SHELF (FIG.1)
The wire shelf allows you to brown or grill food. The shelf can be
used for normal fan heat, conventional cooking and grilling
functions only. It must not be used for any microwave function.
If a microwave function is selected, ensure the wire shelf has been
removed before the start.
ENAMELED TRAY (FIG.2)
The enameled tray allows you to cook foods on normal fan heat,
conventional cooking, and grilling functions. The silicone corners applied
to the enameled tray also allows it to be used in combi microwave
functions. This tray cannot be used during the microwave only function.
Ensure it is removed before using microwave only.
NOTE:
Do not remove the silicone corners, as this could damage the oven.
WARNING:
»Do not use the wire shelf with any microwave function. This could damage the shelf or even
your microwave oven. The wire shelf is for normal convection/fan cooking or grilling only.
»Do not use the enamelled tray with the microwave only function
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
THE SIDE SHELF SUPPORTS (FIG.3)
2 hook-on shelf supports allow you to use the accessories on three levels.
Three cooking levels are available, depending on the method used and the
type of food. With the Grill or Grill + Microwave setting, the accessories
(shelf or tray) are placed on the first level for thick foods like roasts and on
the third level for thinner foods like sausages. In normal cooking modes, or
microwave functions, the shelf or tray should be used on the first or second
levels depending on the item(s) being cooked.
GLASS BASE PLATE (FIG.4)
When microwaving only, foods and beverages can be placed on the
Glass base plate. The Glass base plate protects the bottom of the
microwave cavity from any scratches, marks or spillages. It can also
be easily removed for cleaning by either hand or in the dishwasher.
NOTE:
Always remove the wire shelf when using microwave
functions, as this could damage the oven.
ACCESSORIES

17
Please keep this instruction manual for future reference Instruction manual CM110SS
LIGHT FUNCTION
Press the button once to turn the internal microwave oven lights on & off. The lights will
automatically turn off after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
CHILD LOCK
Hold the button for 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds.
When the Child lock is activated, the symbol will be shown on the display.
Press the button to turn the oven on. When turned on, the display will light up and the time of
day will be shown.
PROGRAMME / FUNCTION
To select a function, press the PROG button to toggle through the functions and press SELECT
once you have reached the required function. Press the °C/W/g button to enter the temperature
(°C), power (W)or weight (g) mode depending on what function has been selected.
To adjust the temperature, power or weight, use the keys followed by SELECT to confirm.
Once confirmed, press the button to start cooking. The main timer will show the actual
temperature, with the set temperature shown above this.
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwave oven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
button for 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwaveoven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
buttonfor 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwaveoven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
buttonfor 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwaveoven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
buttonfor 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
8
OPERATION
Press the button to turn the oven on. When turned on, the display will light up and the time
of day will be shown.
Function / temperature
To select a function, press the / buttons to toggle through the functions and press
SELECT once you have reached the required function. Press the / buttons to adjust the
temperature followed by SELECT again to confirm and start cooking. The symbol will
illuminate on the display whilst the oven is heating up to the required temperature.
The functions are in the below order:
Light function
Press the button to turn the internal oven lights on & off. The lights will
automatically turn off if no operation within 3 minutes.
Boost function BOOST
when the set temperature exceeds 100ºC, you can press the BOOST key to heat up the
oven faster. Once pressed the boost symbol will be displayed on the screen. The boost
function will deactiovate once the oven gets to the set temperature.
The boost function can only be used with the following programmes:
Note: All functions that include the symbols can also use the Rotisserie function. If
required ensure the Rotisserie equipment is inserted into the motor before starting the
programme.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Note: All functions will start after selecting the temperature with the thermostat knob.
Defrost
The air at ambient temperature is distributed inside the oven for defrosting food quicker
Conventional heat
Both the lower and upper heating elements operate together.
This is the traditional cooking method, perfect for roasting joints, cooking pastry and baking cakes.
Eco grill
This function can be used for grilling and gratinating small quantities of food. This function can be used with
the door closed for short times (5-10 minutes). For longer times, half-open the door.
Fan heat
Both the fan and the circular heating element operate together.
The fan evenly distributes the hot air (between 50˚C and MAX) inside the oven. This is ideal for cooking several
types of food i.e. meat and fish at the same time without affecting taste and smell. It is also ideal for delicate
pastries.
10.
OVEN FUNCTIONS
Light
This function turns the light on in the oven only
OPERATION
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwaveoven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
buttonfor 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
8
O T O
ro ramme function
To select a function, press the O button to the functions and press T
have button to enter the
mode
T to conrm.
Once conrmed, press the The main timer will show the actual
temperature, with the set temperature shown above this.
buttononce to turn the internal microwaveoven lights on o. The lights
will automatically turn o after 3 minutes of no operation.
When the light is activated the symbol will be shown on the display.
Child lock
buttonfor 2-3 seconds to activate the child lock. To deactivate, press and hold
the button again for 2-3 seconds. When the Child lock is activated, the symbol will
be shown on the display.
Microwave & Turbo Conventional Fan Heat
Turbo Grill
Turbo Conventional Heat
Defrost
Microwave
Microwave & Turbo Grill
Microwave & Fan Heat
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
4. Timer button.
Setting the time - Press for 3sec to set current time. Adjust time by pressing / . And press
to confirm setting.
Setting timer/alarm. Press to bring up . The display will flash ”0:00”. Adjust time by
pressing / and then press to set the duration. Once the time is up, an alarm will sound and the oven
will switch off. Press any button to cancel the alarm. If you wish to cancel the alarm before it sounds, set time
back to “0:00” to cancel.
Automatic cooking - Once the time has been set, press the until the time starts to flash.
Adjust the end time by pressing / and press to confirm. Oven start time = End time – Duration time.
5. Safety Lock . Pressing for 5sec to enter or cancel the safety lock function.
6. Temperature Setting. Once the function is selected, press to set the temperature. Adjust temperature
by pressing / and press to confirm. Press the button to then start cooking.
7. Boost function . If temperature is set to more than 100°C, you can press this key to heat up
oven faster. Once activated the display will show . The Boost function will stop when the oven gets to
the required temperature.
8. Light function . Press the light button to turn the internal oven light on/off. The light will automatically
turn off if no operation in 3 minutes.
CONTROL PANEL
AUTO
˚C / W/ g
1. Power (on/off)
2. Programme
3. Timer
4. Temperature / Power(wattage) / Weight(grams)
5. Auto cooking
6. Up
7. Down
8. Select
9. Light / Child lock
10. Start/pause
1. Programme / Function
2. Microwave
3. Defrost
4. Auto cooking
5. Temperature / power / weight
6. Timer
7. Time Number display as per below
8. Child lock
9. Light
10. Alarm
11. End time
12. Duration time
13. Temperature/time display
DISPLAY

18 Instruction manual CM110SS18 Please keep this instruction manual for future reference
ALARM SETTING
To set the alarm/minute minder, press the button until the symbol starts to flash.
Use to adjust the time, and then press SELECT to confirm. If you want to cancel the
alarm, set the alarm time back to ‘0.00’ and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash.
To stop the alarm, press any button.
SETTING THE TIME
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the and then press SELECT to confirm.
When the oven is first turned on or restarts, the time must be set before using the oven.
DURATION COOKING(0-10HRS)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. Press to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm , SELECT, and
To cancel Duration cooking set the cooking time to ‘0:00’ and confirm.
END COOKING TIME
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function
and temperature (start time = End time - duration time).
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).

19
Please keep this instruction manual for future reference Instruction manual CM110SS
MICROWAVE OVEN FUNCTIONS
Press the PROG button to select the following functions.
Default power P100 (power range P10-P100).
To adjust the power, press until the correct
power is reached followed by SELECT.
Default time is 30 seconds. To adjust the time press the
button followed by the and SELECT
to confirm. The time will increase in 30 seconds increments
(Max 60mins).
Note: The Duration time when using the microwave
function will display ‘minutes : seconds’, in all other
functions it will show ‘hours : minutes’.
Finally press to start the programme.
Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by
the and SELECT to confirm.
Finally press to start the programme. The default time
will be adjusted according to the set weight (See the
‘Defrost time table’ for more info).
Default temperature 200°C
To adjust the temperature press °C/W/g followed
by . Press SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press
the button followed by the and SELECT
to confirm.
Finally press to start the programme.
Default temperature 200°C
(Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed
by . Press SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the
button followed by the and SELECT
to confirm.
Finally press to start the programme.
Default temperature 200°C
(Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by
. Press SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the
button followed by the and SELECT
to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE
DEFROST
FAN HEAT
TURBO GRILL
TURBO
CONVENTIONAL
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.

20 Instruction manual CM110SS20 Please keep this instruction manual for future reference
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C
(Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode,
and then again to enter the fan heat temperature mode.
These can both then be adjusted using the keys
followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the
button followed by the and SELECT
to confirm.
Finally press to start the programme.
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C
(Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode,
and then again to enter the Turbo grill temperature mode.
These can both then be adjusted using the keys
followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the
button followed by the and SELECT
to confirm.
Finally press to start the programme.
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range
50-220°C).
Press °C/W/g once to enter the Microwave power
mode, and then again to enter the Turbo conventional
temperature mode. These can both then be adjusted using
the keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the
button followed by the and SELECT to
confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
WARNING
»All programmes which include the Microwave function do not require pre-heating, and must
only be used with food inside the oven.
»The enamelled tray cannot be used with the microwave only function
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
»The wire shelf cannot be used with any microwave function
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE &
FAN HEAT
MICROWAVE &
TURBO GRILL
MICROWAVE
& TURBO
CONVENTIONAL
HEAT
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press any button.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm /, SELECT, and
To cancel Duration cooking set the cooking time to '0:00' and confirm.
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Time setting
Time zone can show “Time, Duration time, End of cooking time and Alarm” in this sequence:
All time settings can be operated by pressing
/
, SELECT, and
Alarm setting
To set the Alarm/minute minder, press the button until the symbol starts to flash. Use /
to adjust the time, and then press SELECT to confirm. If you want to cancel the alarm, set the alarm
time back to '0.00' and press SELECT to confirm.
When the time is up, the alarm will sound for 90 seconds, and the symbol will begin to flash. To
stop the alarm, press either , , or SELECT.
Setting the time
To set the time, turn the oven on, and then press and hold the button for 3 seconds until the
time begins to flash. Adjust the time using the / and then press SELECT to confirm.
when the oven is first turned on or restarts, the time must be set before using the oven.
Duration cooking(0-10hrs)
Once a function and temperature have been selected, press the button and the Duration time
will start to flash. press / to adjust the time, and then SELECT to confirm. Once the time is
up, the alarm will sound and the oven will switch off.
Press any of the buttons to turn off the alarm
To cancel Duration cooking set the cooking time to '0:00' and confirm.
/, SELECT, and
End cooking time
Once the Duration cooking time has been set, press twice and the End cooking time should
start to flash. Adjust the time to the time you wish cooking to stop and press SELECT to confirm.
Your oven will then work out when to turn on, so that it cooks for the required duration time, and
finishes at the required end time. E.g. Duration time set at 30 minutes, and the end time set to
18.15, the oven will automatically turn on at 17.45 and cook for 30 minutes on the set function and
temperature (start time = End time - duration time).
Child lock
Press and hold SELECT for 5 seconds to set the child lock. The symbol will appear in the display
once activated.
To cancel the Child lock, press and hold SELECT again for 5 seconds. The symbol will disappear
from the display once deactivated.
Turbo grill - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT
to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Fan heat
Microwave default power P50 (Power range P10-P50).
Fan heat default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the fan heat temperature mode. These can both then be adjusted using the
/ keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
MICROWAVE OVEN FUNCTIONS
Press PROG to select thefollowing functions:
Symbol Description Display
Microwave & Turbo grill
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo grill temperature mode. These can both then be adjusted using
the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed
by the / and SELECT to confirm.
Finally press to start the programme.
Microwave & Turbo conventional heat
Microwave default power P50 (Power range P10-P50).
Turbo grill default temperature 200°C (Temperature range 50-220°C).
Press °C/W/g once to enter the Microwave power mode, and then again to
enter the Turbo conventional temperature mode. These can both then be
adjusted using the / keys followed by SELECT to confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Microwave – Default power P100 (power range P10-P100).
To adjust the power, press / until the correct power is reached followed by
SELECT.
Default time is 1 minute. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Defrost - Default weight 1000g (weight range 100-2000g).
To adjust the weight press the °C/W/g button followed by the / and
SELECT to confirm.
Finally press to start the programme. The default time will be adjusted
according to the set weight (See the 'Defrost time table' for more info).
Fan heat - Default temperature 200°C
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.
Turbo conventional - Default temperature 200°C (Temperature range 50-220°C).
To adjust the temperature press °C/W/g followed by / . Press SELECT to
confirm.
The default time is 1.00hr. To Adjust the time, press the button followed by
the / and SELECT to confirm.
Finally press to start the programme.