Caple CGC611 User manual
Wall Chimney Hood
Instruction Manual
CGC611
CGC711 CGC911
Contact Caple on 0117 938 7420 for spare parts or www.caple.co.uk
Instruction manual CGC611 CGC711 CGC911
2Please keep this instruction manual for future reference
CONTENTS
Introduction 3
Safety Instructions 4
Environmental Protection 9
Installation 10
Operation 15
Care and Maintenance 16
Troubleshooting 18
Product Dimensions 19
Caple Contact Details 20
Instruction manual CGC611 CGC711 CGC911 3
Please keep this instruction manual for future reference
INTRODUCTION
Thank you for choosing this Caple extractor hood.
To ensure that you get the best results from your
new extractor, we strongly suggest that you read this
instruction manual thoroughly before use. If treated with
care, your Caple extractor should give you years of trouble-
free use.
To register ownership, please ensure you complete and
return the guarantee card supplied with the appliance or
visit www.caple.co.uk and register here.
This instruction manual is designed to provide you with
all the required information related to the installation, use
and maintenance of the appliance.
This hood is designed to extract unpleasant odours from
the kitchen; it is not intended to extract steam. In order
to operate the unit correctly and safely, please read this
instruction manual carefully before installation and use.
The cooker hood uses high quality materials and is made
with a streamlined design. Equipped with an electric
motor and centrifugal fan, it provides strong extraction
with low noise. It also features non-stick grease filters and
an easy installation.
Instruction manual CGC611 CGC711 CGC911
4Please keep this instruction manual for future reference
IMPORTANT
This appliance must only be used for the purpose it is
intended. Other types of use are not permitted and may
prove dangerous. Caple will not be held liable for any
damage caused by the incorrect use of the appliance.
Do not use any accessories or attachments not
recommended by Caple as this may result in fire, electric
shock or injury.
To protect against fire, electrical shock and injury to
persons, do not immerse cords or plugs in water or any
other liquid.
Never touch the appliance with wet or damp hands.
Never pull the power cable as you could damage it.
If the appliance is faulty, do not attempt to repair it.
Isolate it from the mains electric supply and contact
Caple Service either by phone 0117 938 7420 or email
service@caple.co.uk
Keep all packaging (including plastic bags, polystyrene
foam etc) out of the reach and away from children.
Do not rest large or unstable objects on any part of the
appliance.
Instruction manual CGC611 CGC711 CGC911 5
Please keep this instruction manual for future reference
IMPORTANT
Caple cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product.
Please note that Caple reserve the right to invalidate
the guarantee supplied with this product following
incorrect installation or misuse of the appliance. Under
no circumstances should any external covers be removed
for servicing or maintenance except by suitably qualified
personnel.
SAFETY INSTRUCTIONS
-Never let children operate the machine.
-The cooker hood is for home use only, not suitable for
barbecuing, restaurants or other commercial purposes.
-The cooker hood and its filter should be cleaned regularly
in order to keep in good working condition.
-Clean the cooker hood according to the instruction
manual to reduce the risk of fire.
-When using a gas hob, do not leave naked flames under
the extractor.
-Before connecting this appliance check that the power
supply cord is not damaged.
-If the room where the hood is to be used contains a fuel
burning appliance such as a central heating boiler then
its flue must be of the sealed or balanced flue type. If
other types of flue or appliances are fitted ensure that
there is an adequate supply of air to the room.
Instruction manual CGC611 CGC711 CGC911
6Please keep this instruction manual for future reference
-The air must not be discharged into a flue that is used
for exhausting fumes from appliances burning gas or
other fuels.
-Regulations concerning the discharge of air have to be
conformed to.
-Do not flambé under the cooker hood.
-Never leave frying pans unattended during use as over-
heated fats and oils may catch fire.
-To ensure the best performance, we recommend
switching on the extractor 15 minutes before cooking
and leave it running 15 minutes after. This will ensure
that the air in the kitchen is being circulated before
cooking commences and the air is being cleaned after
cooking has finished.
-The performance of your extractor will vary depending
on a number of factors. These include type of extraction,
room volume, length of ducting, ventilation available and
the cleanliness of the filters.
-This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
-Children should be supervised to ensure that they do not
play with the appliance.
-Cleaning and user maintenance must not be made by
children without supervision.
Instruction manual CGC611 CGC711 CGC911 7
Please keep this instruction manual for future reference
-Never immerse the appliance in water.
-This appliance is intended to be used in household and
similar applications such as:
› Staff kitchen areas in shops, offices and other
working environments.
› Farm Houses.
› By clients in hotels, motels and other residential
type environments.
› Bed and breakfast type environments.
-To avoid all risk, if the power cable is damaged, it must
only be replaced by a Caple appointed engineer.
-Appliances can be used by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
-Children must not play with this appliance.
-When not in use and before cleaning, always isolate the
appliance from the electrical supply.
Instruction manual CGC611 CGC711 CGC911
8Please keep this instruction manual for future reference
ELECTRICAL SHOCK HAZARD
-Only plug this unit into a properly earthed outlet. If in
doubt seek advice from a suitably qualified engineer.
-Failure to follow these instructions can result in death,
fire, or electrical shock.
-This appliance must be connected to the mains by a
competent person. We recommend that the appliance is
connected by a qualified electrician who is a member of
the N.I.C.E.I.C who will comply with the I.E.E and local
regulations. Electrical information can be found on the
rating plate.
Instruction manual CGC611 CGC711 CGC911 9
Please keep this instruction manual for future reference
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice. This appliance is
marked according to the European directive on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The symbol on the product indicates that this
product may not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. Disposal must be carried
out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local council, your household waste disposal service or the retailer where you
purchased the product
WARRANTY
Your new appliance is covered by warranty. The warranty card is enclosed - if it is missing, you
must provide the following information to your retailer in order to receive a replacement: date of
purchase, model and serial number. Registration can also be completed online by visiting
www.caple.co.uk.
Ensure you keep your warranty card safe, you may need to show it to Caple Service together with
proof of purchase. If you fail to show your warranty card you will incur all repair charges.
Spare parts are only available from Caple Service and spare parts authorised centres.
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all applicable
legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).
UKCA DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all
applicable legislation.
TECHNICAL FICHE
This appliance conforms to all current and applicable energy regulations. To view the Technical
Fiche that supports the energy labelling data, please visit the product page on our
website www.caple.co.uk
Instruction manual CGC611 CGC711 CGC911
10 Please keep this instruction manual for future reference
INSTALLATION
PREPARE FOR THE INSTALLATION:
If you have an outlet to the outside, your cooker hood can be connected
as per the below picture by means of an extraction duct with an interior
diameter of 150mm.
Before installation, turn the unit off and unplug it from the outlet.
The cooker hood should be placed at a minimum distance of 65~76cm
above the hob. It is the manufacturer of the hob who determines the
clearance required and the clearance quoted by the hob manufacturer
must be followed. In the absence of any instructions supplied with a gas
hob the minimum distance between the hob and the hood must be at
least 760mm.
4
4
Earthed Outlet Box
Earthed Plug
Earthed Outlet
4
4
Instruction manual CGC611 CGC711 CGC911 11
Please keep this instruction manual for future reference
INSTALLATION - DUCTED
WARNING:
Observe the warning concerning the operation of the appliance when air is discharged from
the room.
When the cooker hood and appliance supplied with energy other than electricity are
simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4×10-5 Bar).
Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with
the screws and screw plugs provided.
Level up the cooker hood and hang onto the wall bracket hook.
5
5
5
Screw Plug
Wall Bracket
Holes on Wall
Screw
(4mm x 30mm)
Wall Bracket
Cooker Hood
Instruction manual CGC611 CGC711 CGC911
12 Please keep this instruction manual for future reference
After hanging the hood on the bracket, remove the grease filters, mark 2 holes inside the hood for
safety screws. After marking, remove the hood, drill two holes and insert 2 wall plugs and finally
fix the safety screws with 2 screws (ST4x30mm).
Fix the one-way-valve to the air outlet of the cooker hood. Then, attach the exhaust pipe onto the
one-way-valve as shown below.
6
Exhaust pipe
Cooker hood
Exhaust Pipe
Cooker Hood
Instruction manual CGC611 CGC711 CGC911 13
Please keep this instruction manual for future reference
CHIMNEY INSTALLATION
The lower chimney bracket is used to fix the upper decorative chimney and lower decorative
chimney. Use 2pcs 4x8mm screws to attach lower chimney and lower chimney bracket together.
Put the lower chimney on the cooker hood and mark the location of lower chimney bracket fixing
holes on the wall.
NOTE:
Do not fasten screws too much, make sure upper decorative chimney can be telescopically
adjusted after assembled.
Put the chimney on the cooker hood. Fix the lower chimney bracket on the wall by 2 screws
(4mm x 30mm).
Then pulling out the upper chimney upwards to the target height. Adjust to reach the height
required.
Fix the upper chimney on the upper chimney bracket by 2 screws (4x8mm). Then fix the upper
chimney bracket on the wall. Before fixing the bracket on the wall, you can decide the upper
chimney bracket fixing holes for installation.
7
Upper Chimney (Inner)
Lower Chimney bracket
Lower Chimney (Outer)
Wall Plug
Plate ||
Screw (4mm x 8mm)
Screw (4mm x 30mm)
Instruction manual CGC611 CGC711 CGC911
14 Please keep this instruction manual for future reference
INSTALLATION – RECIRCULATION MODE
If you do not have an outlet to the outside, the
exhaust pipe is not required (as shown in the
section “Installation - ducted”), and charcoal filters
must be installed.
INSTALLING THE CHARCOAL FILTER (CAP75CF)
An activated charcoal filter can be used to trap odours. In order to install the charcoal filter, the
grease filter should be detached first. Press the release button and pull it downward as shown
below.
To fit the charcoal filter, line up part A of the charcoal filter with the rear bar, and part B of the
filter with the front of the hood. Push the filter into
this space to secure it. There are 2 clips on part B
which lock the filter into place once it has been
pushed in.
After assembly, the charcoal filter should be as below:
NOTE:
Make sure the filter is securely fitted. Otherwise, it
could loosen and fall out. This could cause damage
to the appliance and danger to the user. When the
activated charcoal filter is used, the extraction rate
will be lower.
8
, and
charcoal filters must be installed.
9
(CAP61CF)
We recommend replacing these filters every 6 months. Replacement
filters (CAP61CF) can be purchased directly from www.caple.co.uk
To fit the charcoal filter, line up part A of the charcoal filter with the rear bar, and part B
of the filter with the front of the hood. Push the filter into this space to secure it. There
are 2 clips on part B which lock the filter into place once it has been pushed in.
harcoal uld be
ely fitted. could and fall out. This could
cause damage to the appliance and danger to the user. the a charcoal
is used, extraction rate
Charcoal filter
To fit the charcoal filter, line up part A of the charcoal filter with the rear bar, and part B
of the filter with the front of the hood. Push the filter into this space to secure it. There
are 2 clips on part B which lock the filter into place once it has been pushed in.
harcoal uld be
ely fitted. could and fall out. This could
cause damage to the appliance and danger to the user. the a charcoal
is used, extraction rate
Charcoal filter
Instruction manual CGC611 CGC711 CGC911 15
Please keep this instruction manual for future reference
OPERATION
OFF BUTTON
Switches the extraction fan off.
LOW SPEED BUTTON
Is suitable for simmering and cooking which does not produce much odour.
MEDIUM SPEED BUTTON
Airflow speed is ideal for extracting with standard cooking.
HIGH SPEED BUTTON
When a high amount of smoke or odour is produced, press the high speed button
for the most effective extraction.
LIGHT BUTTON
Switches the light on and off.
10
10
10
10
10
10
Instruction manual CGC611 CGC711 CGC911
16 Please keep this instruction manual for future reference
CARE AND MAINTENANCE
IMPORTANT:
Before cleaning or maintenance please switch off the electricity supply and remove the plug from
the wall.
REGULAR CLEANING
Use a soft damp cloth with lukewarm mildly soapy water or household cleaning detergent. Never
use metal pads, chemicals, abrasive material, abrasive cleaning creams or stiff brushes to clean the
appliance.
CLEANING THE GREASE FILTER
Clean the filter every month to help minimise the risk of fire. The filter collects grease, smoke and
dust, therefore the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the
grease residue (which is potentially flammable) will saturate the filter. It can be easily cleaned with
warm water and washing up liquid, alternatively the filters can be cleaned in your dishwasher.
Please ensure no other items are washed with the filters, they must be washed separately to
prevent food becoming trapped in the gauze. Cleaning the grease filters in the dishwasher may
lead to discolouration, this is normal and is a not a fault with the product.
REPLACING YOUR CHARCOAL FILTER
This only applies if you are using the hood in recirculation mode (not vented to the outside). The
charcoal filter traps your cooking odours and they need to be replaced, this can vary depending on
how frequently the cooker hood is used. We recommend replacing them at least every 6 months.
This extractor uses CAP75CF charcoal filters.
Filters can be purchased directly from www.caple.co.uk.
Instruction manual CGC611 CGC711 CGC911 17
Please keep this instruction manual for future reference
REPLACING THE BULB
NOTE:
The lights must be replaced by a qualified person.
1. Switch the unit off and unplug the appliance.
2. Remove the 4 screws on the curved glass panel, and take off the glass carefully.
3. Unplug the light from the connector and then push the light out of the hood.
4. Replace with the same type and rated bulb/lamp fixing. LED lamp (max 2W).
5. Connect the replacement light and screw the glass panel back on securely.
B image
LIGHT SOURCE ENERGY CLASS
This product contains a light source of energy efficiency class G.
Instruction manual CGC611 CGC711 CGC911
18 Please keep this instruction manual for future reference
TROUBLESHOOTING
FAULT CAUSE SOLUTION
The lights on, but the fan
does not work
The fan blade is jammed. Switch off the unit and contact
Caple Service. To be repaired by qualified
service personnel only.
The motor is damaged.
The lights and fan
do not work
A blown fuse. Replace the fuse.
The power cord is loose. Plug in to the power supply again.
Serious vibration of the unit
The fan blade is damaged.
Switch off the unit and contact
Caple Service. To be repaired by qualified
service personnel only.
The fan motor is not fixed tightly.
Switch off the unit and contact
Caple Service. To be repaired by qualified
service personnel only.
The unit is not hung correctly on the
bracket.
Take down the unit and check whether the
bracket is in the correct location.
The extraction performance
is not good The filter requires cleaning.
Clean the grease filter as directed in the
‘Care and maintenance’ section. Replace the
charcoal filter (if in recirculation mode).
If the above table has not solved the problem please contact Caple Service by phone on
0117 938 7420 or by email service@caple.co.uk
Instruction manual CGC611 CGC711 CGC911 19
Please keep this instruction manual for future reference
PRODUCT DIMENSIONS
266mm
259mm
560-1040mm
500mm
90mm
895mm
266mm
259mm
550-1030mm
500mm
56mm
695mm
266mm
259mm
533-1013mm
500mm
64mm
595mm
CGC911BK
CGC911SS
CGC711BK
CGC711SS
CGC611BK
CGC611SS
Caple Service
Fourth Way
Avonmouth
Bristol
BS11 8DW
T: 0117 938 1900
E: service@caple.co.uk
www.caple.co.uk
Other manuals for CGC611
1
This manual suits for next models
2
Table of contents
Other Caple Ventilation Hood manuals
Popular Ventilation Hood manuals by other brands
ELICA
ELICA WAVE UX BL/F/51 Instruction on mounting and use
Lang
Lang LVC-46 Installation and operation instructions
Faber
Faber Scirocco Downdraft Rangehood instruction manual
Fujioh
Fujioh BUF-08W installation manual
CDA
CDA ECHK90 Manual for installation, use and maintenance
ELICA
ELICA YE Series Instruction on mounting and use
Vent-Axia
Vent-Axia Genova 120801A Instruction on mounting and use
Tricity Bendix
Tricity Bendix CH 550 Operating and installation instructions
Pelgrim
Pelgrim ISWA0960 Series Instructions for use
Amica
Amica AH3016 instruction manual
Electrolux
Electrolux EI30HI55KS Installation, use & care guide
XO Appliance
XO Appliance XOBI XOBI36SC manual