Car-Interface.com CI-RL-LR12-TF User manual

Version 28.05.2014 CI-RL-LR12-TF
r.LiNK-Interface
CI-RL-LR12-TF
Rear-view camera-input
and
video-in-motion
for Landrover
touch-screen navigation systems
from model 2012
Only for vehicles WITHOUT factory rear-view camera

Version 28.05.2015 RL-LR12-TF
Page1
Contents
1. Prior to installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the Dip-switches of the CAN-Box TV-400/500
1.4. Pin-assignments
2. Connection schema
3. Installation
3.1. Interconnecting CAN-box, harness and factory navigation monitor
3.2. Connection to rear-view camera
4. Activation of the video-in-motion function
5. Specifications
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.

Version 28.05.2015 RL-LR12-TF
Page2
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
CAN-box TV-400/500
HW_____ SW_____
Harness
TV-LR02
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Adapter
CAB-TVAS20
Requirements
Vehicle Land Rover Range Rover Evoque L538, Range Rover Sport L320,
Discovery 4 L319
from year 2012
Navigation Touch-screen navigation version 3
Limitations
After-market rear-view Only compatible with NTSC-cameras.
camera

Version 28.05.2015 RL-LR12-TF
Page3
1.3. Setting the dip switches of the CAN-box TV-400/500
TV-400
Note: Setting dip 1 to ON codes the factory rear-view camera input which is located on the
6pin male connector of the factory monitor. When reverse gear is engaged, the navigation
will automatically switch to this input.
TV-500
Vehicle/ navigation
Dip 1
Dip 2
Dip 3
Dip 4
Dip 5
Dip 6
Video-in-motion permanent
ON
ON
OFF
OFF
ON
ON
Video-in-motion selective*
OFF
ON
OFF
OFF
ON
ON
* With dip1 to OFF the included green cable is used to activate the video-in-motion function
Note: Dip switch functions of the TV-500
Dip 1 –activation TV-free
Dip 2 –rear-view camera existing
Dip 3 –TV icon simulation
Dip 4 –no function
Dip 5 –CAN-bus termination resistor on the vehicle side
Dip 6 –CAN-bus termination resistor on the head-unit side
Setting dip 2 to ON codes the factory rear-view camera input which is located on the brown
Fakra male connector of the factory monitor. When reverse gear is engaged, the navigation
will automatically switch to this input. On vehicles with factory rear-view camera set Dip 2 to
ON, too.
Alle vehicles dip 1 ON, dip 2 ON, dip 3 ON

Version 28.05.2015 RL-LR12-TF
Page4

Version 28.05.2015 RL-LR12-TF
Page5
1.4. Pin-assignments
Pin-assignment factory monitor connector
No liability for vehicle wire colors and pin definition! Possible changes by the vehicle
manufacturer. The given information must be verified by the installer.
Pin-assignment of the CAN-Box TV-400 (Molex 8pin)
Cable colour
Pin-No.
Assignment
●Yellow
Pin 4
CAN-HIGH –connection to the head-unit
●Blue
Pin 3
CAN-LOW –connection to the head-unit
●●Yellow/Black
Pin 8
CAN-HIGH –connection to the vehicle
●●Blue/Black
Pin 7
CAN-LOW –connection to the vehicle
●Red
Pin 1
+12V permanent
●Black
Pin 5
Ground
●Green
Pin 6
Activation of the video-in-motion function
(+12V = TV-free activated)
●White
Pin 2
Trigger output (+12V DC 500mA)
Cable colour
Assignment
●●Orange/grey
CAN-HIGH Pin 2
●●Orange/purple
CAN-LOW Pin 1

Version 28.05.2015 RL-LR12-TF
Page6
2. Connection schema
3. Installation
Switch off ignition and disconnect the vehicle’s battery! If according to factory rules
disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in
sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a
resistor lead.
Place of installation is on rear of the factory navigation monitor.

Version 28.05.2015 RL-LR12-TF
Page7
3.1. Interconnecting CAN-Box, harness and factory navigation monitor
Connect female 8pin Molex connector of harness TV-LR02 to male 8pin Molex
connector of CAN-box TV-400/500.
Transfer female 16pin connector of vehicle harness from rear of the factory
navigation monitor into male 16pin connector of harness TV-LR02.
Plug female 16pin connector of harness TV-LR02 into male 16pin connector on the
rear of the factory navigation system.
3.2. Connections to rear-view camera
Connect female Fakra-connector of adapter CAB-TV-AS20 to the male purple Fakra-
connector on the rear of the factory navigation monitor.

Version 28.05.2015 RL-LR12-TF
Page8
Connect the video RCA of the rear-view camera to the female RCA connector of
adapter CAB-TV-AS20.
Note: Only compatible with NTSC-cameras.
4. Activation of the video-in-motion function
TV-400
The video-in-motion function is activated permanently without disturbing the navigation
performance.
Note: The loose white and green cable are not required and must be isolated.
TV-500
The video-in-motion can be activated and deactivated by Dip 1 or alternatively by the
included loose green cable in connection with a switch (not included in delivery).
Video-in-motion permanent
With dip1 to ON the video-in-motion function is activated permanently without disturbing
the navigation performance.
Video-in-motion selective
With dip1 to OFF the included green cable is used to activate the video-in-motion function.
Connect a switch to the green cable and connect the green cable to +12V ACC.
●+12V = TV-Free is activated
●0V = TV-Free is not activated
Note: The loose white cable is not required and must be isolated.

Version 28.05.2015 RL-LR12-TF
Page9
5. Specifications
Operation voltage 10.5 –14.8V
Stand-by power drain <2mA
Operation power drain ~60mA
Power consumption ~0,08W
Temperature range -30°C to +80°C
Weight 44g
Measurements (box only) W x H x D 70 x 20 x 47 mm/ 76 x 27 x 54 mm
Legal disclaimer: Mentioned company and trademarks, as well as product names/codes are registered
trademarks ® of their corresponding legal owners.