Carefree PARAMOUNT User manual

052548-001r1 Printed in USA October, 2007
INSTALLATION MANUAL
PARAMOUNT
RV
2-Stage Multi-Position Awning
¾Self contained, no need for additional awning rails or other attachments;
¾Mounting does not interfere with the side walls, windows or other
accessories, the awning can be positioned without concern of obstructions;
¾Available for single, double and quad installations;
¾Lateral support 2- stage arm design;
¾3 pre-set extend positions: Side-Out Cover, Side-Out Cover + Window, and full Patio extension.
¾Direct Response Auto-Retract system, the latest in electronic controls with automatic retract, sensitivity
control and no anemometer. The system includes an RF remote;
¾New key pad design provides a positive tactile feel and total control for all the awnings in one master panel
including Standard Operation, Position Control and the Direct Response sensitivity settings.
PROPRIETARY STATEMENT
The Paramount Patio Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The information contained in or
disclosed in this document is considered proprietary to Carefree of Colorado. Every effort has been made to ensure that the information presented
in the document is accurate and complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result from the
use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the title page. Earlier model configurations
may differ from the information given. Carefree of Colorado reserves the right to cancel, change, alter or add any parts and assemblies, described
in this manual, without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado products only. Any other reproduction or
translation of this document in whole or part is strictly prohibited without prior written approval from Carefree of Colorado.
Table of Contents

052548-001r1 Printed in USA October, 2007
TABLE OF CONTENTS
Product Overview.......................................................................................................................... 1
Component Checklist..............................................................................................................................2
Installation – Mechanical..............................................................................................................4
Required Pre-Installation Parameters.....................................................................................................4
Mounting Plate Layout and Installation...................................................................................................4
Mounting the Awning Unit.......................................................................................................................5
Installation – Electrical.................................................................................................................. 6
Component Installation...........................................................................................................................6
Key Pad Installation........................................................................................................................6
Control Box Installation ..................................................................................................................7
Ignition Lockout Sensor Installation (Optional) .......................................................................................7
Installing the Remote Receiver (All Configurations) ...............................................................................8
Programming the Receiver for the Remote ....................................................................................8
Wiring Diagram – Single Awning ............................................................................................................9
Wiring Diagram – 2-Awnings ................................................................................................................10
Wiring Diagram – 4 Awnings ................................................................................................................12
Connection Flex w/ "110VDR" Control Boxes ......................................................................................14
Optional Manual Bypass Switch ...........................................................................................................14
Testing the System ...............................................................................................................................15
Standard System Adjustments ..................................................................................................16
Setting the Motor Limits........................................................................................................................16
Adjusting the OUT Limit Switch....................................................................................................16
Adjusting the IN Limit Switch........................................................................................................16
Adjusting the Lead Rail.........................................................................................................................17
Adjusting the Lead Rail Height .....................................................................................................17
Adjusting the Horizontal Lead Rail Position..................................................................................17
Manual Override ...................................................................................................................................18
SAFETY INFORMATION
WARNING
AWARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION WHICH,IF NOT AVOIDED,COULD RESULT IN
DEATH OR SERIOUS INJURY AND/OR MAJOR PROPERTY DAMAGE.
CAUTION
ACAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION THAT MAY CAUSE MINOR TO MODERATE
PERSONAL INJURY AND/OR PROPERTY DAMAGE.IT MAY ALSO BE USED TO ALERT AGAINST UNSAFE PRACTICES.
NOTE: A note indicates further information about a product, part, or step.
Tip: A tip provides helpful suggestions.
Safety Notes:
•Always disconnect battery or power source before working on or around the electrical system.
•Always wear appropriate safety equipment (i.e. goggles).
•Always use appropriate lifting devices and/or helpers when lifting or holding heavy objects.
•When using fasteners, use care to not over tighten. Soft materials such as fiberglass and aluminum
can be "stripped out" and lose the ability to grip and hold.
Reference Publications located @ www.carefreeofcolorado.com:'
052548-001 Paramount Installation Manual
052548-201 Paramount Owner's Manual
052548-301 Paramount Service Manual
Carefree of Colorado 2145 W. 6
th
Avenue Broomfield, CO 80020
aScott Fetzer company 303-469-3324 ♦www.carefreeofcolorado.com

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 1
PRODUCT OVERVIEW
The Paramount Patio Awning offers the coach owner an awning system that provides as much or as little
shade as required. The canopy is housed in an aluminum case that easily blends in with the coach roof.
Each unit is equipped with lateral support arms that are the strongest available on the market. No vertical
arms interfere with coach sidewalls or equipment that may be mounted on the roof.
The unique and innovative 110V electronic control system provides Carefree’s Direct Response system with
interior pushbutton controls for standard extend/retract functions. At the master control panel the auto-retract
system can be engaged to automatically retract the awning in windy conditions. Sensitivity can be set to respond
to a variety of wind speed conditions. An RF remote is furnished with the Direct Response system.
Paramount Patio Awning Specifications
The following information is for reference only. Specific information is detailed in the installation instructions.
7.13”
12.75”
A (Awning Length)
Paramount001
Top View Profile
LENGTH 14’ – 21’ (in 1 foot increments)
Position: Slide-Out Window Patio
EXTENSION: 40" 72" 106"
LEAD RAIL DROP 6" (20°) 32" (33°) 51" (33°)
Values are approximate, actual dimensions may vary with specific installations.
Angles are measured from horizontal (parallel to ground)
MOTOR SPECIFICATIONS:Available in LH or RH configurations
Type: Tubular Motor
Power: 120V, 60HZ, 2.5A
Torque: 60 nm
Speed: 14 RPM
Cycle: 40 Sec ON / 1 Min OFF
CONTROLS: Direct Response Electronics with a single master control and single remote for all awnings.
COLOR: Hardware: White, Black
Fabric: Woven Acrylic Fabric
APPROXIMATE INSTALLED WEIGHT (LBS.)
Awning Length (ft.) Weight Awning Length (ft.) Weight Awning Length (ft.) Weight
14 206.5 17 229 20 251.5
15 214 18 236.5 21 259
16 221.5 19 244
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 2
COMPONENT CHECKLIST
6
1
2
7
920
22
23
24 25
8
5
43
10
11
13
12
14
15
18
16
19
17
21
Paramount002
Single Awning Electronics
Dual Awning Electronics
4-Awning Electronics
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 3
;ITEM DESCRIPTION QTY NOTE
1 Awning Assembly 1 1
2 Mounting Bracket 4 2
3 Screw, Thread Cutting 3/8 x 1 1/2 24
4 Screw, Hex Head 5/16-18 x 1 1/2 4
5 Square Nut 5/16-18 4
6 Hex Key 7mm x 133mm 1
7 Key Pad Switch Assy Single Awning 1 3,4
8 Control Box Single Awning 1 3
9 Screw #8 x 3/4 4
10 Remote Control, 433MHz Single Awning 1 3,5
11 Key Pad Switch Assy Dual Awning 1 3,4
12 Control Box Dual Awning 1 3
13 Screw #8 x 3/4 4
14 Remote Control, 433MHz Dual Awning 1 3,5
15 Key Pad Switch Assy 4-Awning Combo 1 3,4
16 Control Box, Box #1 4-Awning Combo 1 3
17 Control Box, Box #2 4-Awning Combo 1 3
18 Screw #8 x 3/4 8
19 Remote Control, 433MHz 4-AwningCombo 1 3,5
20 RF Receiver, 433MHz 1
21 Screw #6 x 1/2 2
22 RJ11 Cable 60 inches NOTE 6
23 RJ11 Cable, used with items 11 & 15 20 feet 1
24 Sensor, Ignition Lock-Out 1 7
25 Splitter 1 7
Notes: 1. Awning configuration is specified at time of order, including awning length, LH or RH
configuration, fabric color etc. Check awning assembly against original purchase order.
2. Quantity of 4 per awning is standard for item 2-mounting brackets. Some Original Equipment
Manufacturer (OEM) installations may specify a different quantity.
3. Electronic components are not interchangeable between systems.
4. Mounting screws are included with switches and switch plate.
5. Additional remotes can be ordered separately.
6. 60" cable (item 22) is furnished with items 7, 20 and 24 and one additional cable is furnished
with the 4-awning control boxes (items 16, 17).
7. The optional ignition lockout and splitter (items 24, 25) must be ordered separately
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 4
INSTALLATION –MECHANICAL
The following instructions are for the physical installation of one Paramount awning. Repeat the
instructions for each awning to be installed.
REQUIRED PRE-INSTALLATION PARAMETERS
Prior to installing the awning system, the installer must determine the layout of the system and provide
specific construction elements to successfully assemble the awning components.
1. Determine the location, size and type of awning to be mounted.
•There must be structure at the awning mount locations. Fiberglass or sheet metal alone is NOT
strong enough to support the weight of the awning!
WARNING
THE PARAMOUNT AWNING HAS SIGNIFICANT WEIGHT.THE AWNING AND ATTACHING BRACKETS MUST BE SECURELY
FASTENED TO THE STRUCTURAL FRAME OF THE ROOF.CONSULT THE COACH MANUFACTURER TO DETERMINE THE TYPE
AND POSITION OF THE ROOF'S STRUCTURAL MEMBERS AND THE STRUCTURE'S ABILITY TO SUPPORT THE WEIGHT.
FAILURE TO HEED THIS WARNING CAN RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE
2. Determine the mounting locations for the control box and switch assemblies.
•For 110VAC installations, the installer must provide enclosed junction boxes for all wire splices. Boxes are
required in conformance with prevailing construction codes.
•At the control box location, AC input is required. It is recommended that the installer provide a
dedicated AC circuit for the awning system that is protected by an appropriate sized fuse/circuit
breaker. Each patio awning draws a maximum of 3 amps.
•The motion sensor for the Direct Response system is mounted on the patio awning. 10 feet cable is
available from the awning wall mount, and will require a routing path to the control box. If the control box is
located at a distance greater than 10 feet, the installer must provide a terminated jumper cable from the
box location to the cable end.
3. For installations over a slide-out room, an installer furnished gutter should be installed between the
awning and room to prevent runoff spilling from under the awning onto the top of the room. (See profile
detail below.)
MOUNTING PLATE LAYOUT AND INSTALLATION
The Paramount Patio Unit is mounted using four (4) 22” mounting brackets.
3” (typ)
A
3.7”
7.68”
8”
8” (typ)
9” (typ)
22”
4 25”
B
C
L (Awning Length)
Paramount
003
3/8-16 x 1 1/2
Self Tapping Screw
5/16-18 x 1 1/2
Retaining Bolt
& Square Nut
Top View
Profile Mounting Plate Hole Pattern
Installer Furnished
Rain Gutter
1” Minimum Depth
1” Area Cross Profile
D
Figure 1. Mounting Plate Pattern.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 5
L (feet) A (inches) B (inches) C (inches) D (inches)
14' to 16'11" 13" 55" L - 55" L - 13"
17' to 19'11" 14" 65" L - 65" L - 14"
20' to 21' 25" 76" L - 76" L - 25"
1. Determine the location of the awning mounts:
1.1 Mounting area must be flat and clear of obstacles,
1.2 The awnings have appreciable weight; the mounting screws MUST fasten into the structure.
2. (refer to Figure 1) Position the mounting plates on the coach roof. Horizontally position the plates
using the dimension in the chart.
3. Position a mounting plate and use the plate as a template to drill one 11/32” pilot hole into the
structure. Attach the plate using a 3/8-16 x 1 1/2 thread cutting screw.
4. Confirm position of plate and repeat step 6 on the opposite end of the mounting plate.
5. Continue to drill and attach using the 3/8-16 x 1 1/2 thread cutting screws for 6 mounting holes per plate.
6. In the rear track of each mounting plate, start one (1) 5/16-8 screw and square nut through hole in back of
mounting plate. Do not tighten at this time.
7. At the motor location, drill one (1) 1/2” hole through outer surface. The position may be under or behind the
end plate position.
MOUNTING THE AWNING UNIT CAUTION
IT IS RECOMMENDED THAT AT LEAST THREE PEOPLE INSTALL THE AWNING DUE TO THE SIZE AND WEIGHT OF THE
COMPONENTS!
Paramount004
5/16-18 x 1 1/2
Retaining Bolt
& Square Nut
(ref)
Mounting Bracket
(ref)
Figure 2. Mounting the Awning.
1. While lifting the awning, route the awning motor wires through the 1/2” hole drilled previously.
NOTE: It is necessary to first insert the sensor cable and connector through the hole then
insert the motor wires.
2. Set the awning into the hooks of the mounting bracket. Pull the case forward to fully engage the
bracket.
3. Adjust the horizontal position of the awning as required.
4. Tighten the securing bolts. Torque to 10 ft-lbs.
5. Seal the wires and access hole with a quality silicone sealant.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 6
INSTALLATION –ELECTRICAL
WARNING
ALWAYS DISCONNECT THE VEHICLE BATTERY AND ELECTRICAL SOURCES BEFORE WORKING WITH ELECTRICAL
WIRING AND COMPONENTS.
IMPORTANT NOTICES:
•Failure to follow the wiring instructions in this publication may void the warranty.
•All wiring must conform to NEC (National Electrical Code) and local codes.
•DO NOT wire two or more motors to one motor controller.
•The SO cable from the 110VAC awning motor can only pass directly through a wall, it can not be
laid up in the wall and must be connected to NM wire or individual wires in conduit no more than
6 inches past the point of entry.
•The installer must provide enclosed junction boxes for all 110VAC wire splices. Boxes are
required in conformance with prevailing construction codes. Installers are required to furnish
the UL approved electrical boxes where required.
•At the control box location, 110V power is required. It is recommended that the installer provide
a dedicated AC circuit for the awning system that is protected by an appropriate sized
fuse/circuit breaker. Each patio awning draws a maximum of 3 amps.
•The motion sensor for the Direct Response system is mounted on the patio
awning. 10 feet of cable is available from the awning wall mount, and will
require a routing path to the control box. If the control box is located at a
distance greater than 10 feet, the installer must provide a terminated
jumper cable from the box location to the cable end.
•Terminated cable is a 4-wire RJ11 terminated phone cord (straight, no
twist).
NOTE: Cable lengths of the furnished cables are listed in the chart with
the system wiring diagram. If a connection requires a length
greater than the supplied cable, the installer must provide a
terminated cable from the box location to the cable end.
COMPONENT INSTALLATION
Key Pad Installation
1. Locate the mounting location of the key pad. The key pad
requires a flat area approximately 2 3/4" wide by 4 1/2" tall.
2. Use the mounting plate as a template and mark the location
of the two mounting holes.
3. Remove the plate, mark and cut a 1" hole in the position
shown.
4. Mount the plate to the surface using the included screws.
5. Route the 25 foot RJ11 cable from the control box location
through the wall and mounting plate.
6. Attach the cable to the back of the key pad then attach the
key pad to the mounting plate.
NOTE: The key pad attaches to the plate with magnetic
latches. No additional attaching hardware is
required.
Black
Red
Green
Black
Yellow
Red
Green
Yellow
Cables are 4-wire RJ11
terminated phone cord
(straight, no twist).
RTA031
1.25”
O 1” min.
O .125” Pilot Hole
(2 plcs)
RJ11 Cable
Mounting Plate
Key Pad
Paramount005
4.5”
3.25”
(ref)
2.75”
Figure 3. Key Pad Installation.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 7
Control Box Installation
NOTE:
a) For Multiple Awing Installations: The awning motor connected to the controller board marked
"motor #1" will correspond with "Awning 1" on the key pad control and remote. The awning
motor connected to "motor #2" will correspond with "Awning 2" on the controls etc.
b) The control boxes are not suitable for exterior installations and must be mounted in the
INTERIOR of the vehicle.
For Single Awning installations: refer to wiring diagram on page 8.
For 2- Awning installations: refer to wiring diagram on page 10.
For 4-Awning installations: refer to wiring diagram on page 12.
1. Locate the mounting location of the control box(es).
Each box requires a flat area approximately 6 1/2" x
6 1/2" with a clearance depth of 2 3/8".
For 4 awning installations: A 60" jumper cable is used
between the two control boxes. This allows
approximately 55" of cable between the boxes.
Position the boxes to allow the jumper to be connected
and routed with some slack in the cable.
2. Remove the lid. Attach the box to the mounting surface
using a minimum of two (2) #8 x 3/4 screws each. The
screws must be mounted in opposite corners.
3. Route a 2-conductor 14AWG NM wire with ground from the AC power source to the box. It is
recommended that the installer provide a dedicated AC circuit that is protected by an appropriate sized
fuse/circuit breaker. Each patio awning draws a maximum of 3 amps.
NOTE: Each board must have a 110VAC supply. The diagram shows a separate power source for
each box; each power source is spliced with wire nuts to power both boards in a box.
4. Connect the wires to the control box circuit boards as shown in the wiring diagram (Detail A).
5. Route the motor wires from awning #1 to controller #1 (motor#1); attach the wires to the terminals as shown.
NOTE: For LH motor configurations:
RED WIRE goes to terminal (1); BLACK WIRE goes to terminal (2).
For RH motor configurations:
RED WIRE goes to terminal (2); BLACK WIRE goes to terminal (1).
6. Attach the RJ11 cable from the sensor of awning #1 to the "AMD" receptacle of controller #1.
7. Repeat step 5 and 6 for the other awnings.
8. After testing connections, use Loctite 29005 or equivalent to secure screws in terminal block.
9. Attach the remaining RJ11 cables as shown in the wiring diagram. Use the slot cutouts in the box to
route the phone cables.
NOTE: The key pad and RF receiver only attach to controller #1.
IGNITION LOCKOUT SENSOR INSTALLATION (OPTIONAL)
Two optional Ignition Lockout Sensors are available with the Direct Response system. As a travel safety
feature, the sensor disables the extend function when the ignition key is turned on. The RTL lockout will
retract the awning and disable the extend function.
1. Connect the cable to any open “EYE” port in the control boxes.
2. Route the cable as desired and connect the cable to the sensor.
3. Attach a wire (16-20 AWG) to the ground terminal of the sensor and route the wire to a suitable ground.
4. Attach a 2nd wire (16-20 AWG) to the 12VDC of the sensor and route the wire to a SWITCHED 12VDC
source. A switched 12VDC source is a line that is hot only when the ignition is in the on position. Wires
to the sensor are not pin specific.
5. Bundle and secure the sensor, cable and wires as required in an environmentally protected area..
#8 x 3/4 Screw (2)
RTA019c
6 1/2”
(typ)
2 3/8”
Figure 4. Control Box.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 8
INSTALLING THE REMOTE RECEIVER (ALL CONFIGURATIONS)
1. Determine the location of the RF receiver:
1.1 Do not mount the unit near heat producing elements
such as LP appliances or engine exhaust
components.
1.2 For best reception, do not mount the unit near or on
a metal surface.
1.3 Mount the unit with the antenna pointing up.
1.4 The included cable is approximately 60 inches long.
Mount the unit close enough to the splitter or control
box so that the cord can be connected without
stressing the connections.
1.5 Allow adequate room below the box to access the connector jack, programming button and
indicator light.
2. Position the control box and secure using two (2) #6 x 1/2” screws.
NOTE: If the box is mounted on a surface that is less that 1/2” thick, the screws will protrude
through the opposite side of the surface.
3. Connect the cable to the receiver.
4. Route the cable to the control box and connect to any open “EYE” port.
Programming the Receiver for the Remote
1. Power to the control box must be on.
2. Press and release the “Press to Learn Transmitter” button on
the bottom of the receiver box. The receiver is in program
mode when the red light comes on.
3. Press and release ANY button on the remote. It is
recommended to use the STOP button. The red light will go out
after the receiver learns the remote signal.
CAUTION
WHEN THE RECEIVER LEARNS THE TRANSMITTER SIGNAL,THE SYSTEM WILL
PERFORM THE OPERATION OF THE BUTTON PRESSED.EXAMPLE:
PRESSING AN "EXTEND"BUTTON DURING THE LEARNING PHASE WILL
CAUSE THE AWNING TO EXTEND WHEN THE RECEIVER LEARNS THE SIGNAL.
USE CAUTION TO AVOID UNEXPECTED MOVEMENT BY THE AWNING.
4. Repeat steps 2 and 3 for each additional remote.
OPERATIONAL NOTES:
•Transmitter and receiver operate on a frequency of 433MHz.
•The receiver exits the program mode after ten seconds.
•If the light does not come on in step 2, check the continuity of the cord between the boxes and repair
or replace as required. Pin 1 of the 1st connector goes to pin 1 of the 2nd connector etc. If the light still
does not come on, the memory is full and must be cleared.
•If the light does not go out in step 3, the receiver already knows the transmitter's signal or the
battery in the remote needs to be replaced.
•To clear the memory: PRESS AND HOLD the transmitter learn button. While holding the button, the
indicator light should be OFF for the full 5 seconds then come on.
•The system may be programmed for up to 5 remotes. Additional remotes may be ordered
separately.
RTA034
1”
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
3 7/8”
4 3/16”
#6 x 1/2
Screw (2)
Figure 5. RF Receiver.
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
Program
Button
Indicator
Light
RTA022
Figure 6. Programming the Receiver.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 9
WIRING DIAGRAM –SINGLE AWNING
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR013
Ignition Switched
+12VDC
12VDC
Ground
Ignition
Lockout
Sensor
(Optional)
Splitter
Sensor
Key Pad
Awning #1
3
5
4
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
AMDSUNAUXEYEDSK
BLK
WHT
RED
GRN
grn
wht
blk
1
7
6
5
4
3
2
1
7
6
5
4
3
2
3 Conductor 14AWG NM Wire w/ Gnd
Sensor
Remote
Red
Black
White
Green (Ground)
1Wire Legend:
2For LH Motor Configurations:
Motor Red goes to Pin (1); Motor Black goes to Pin (2)
For RH Motor Configurations:
Motor Red goes to Pin (2) Black; Motor Black goes to pin (1)
3The SO cable from the 110VAC awning motor can only pass through a wall, it cannot be laid up in the wall
and must be connected to NM wire or individual wires in conduit no more than 6 inches past the point of entry.
NOTES:
4
Wires for the Ignition Lock-Out Sensor are not pin specific.
5
Splitter is used only when Optional Lock-Out Sensor is installed. Connect RF Receiver directly to “EYE”
if Lock-Out is not installed.
Detail A
For RH Configuration
Reverse Red & Black Wires
RED
WHT
BLK
GRN
grn
wht
blk
FROM TO (RH CONFIGURATION) TO (LH CONFIGURATION)
Black 1 2
Red 2 1
White 3 3
Motor
Ground
Control Box
6
Control Box
6
White 4 4
Black 5 5
AC Power
Source
Ground
Control Box
7
Control Box
7
Awning Sensor 10’ Cable Control Box “AMD” Control Box “AMD”
Key Pad 60“ Cable Control Box “DSK” Control Box “DSK”
Splitter 60" Cable Control Box "EYE" Control Box "EYE"
RF Receiver 60” Cable Splitter "EYE" Splitter "EYE"
Ignition Lockout 60“ Cable Splitter "EYE" Splitter "EYE"
Notes: 1. Cable lengths are the lengths of the furnished cables. If a connection requires a length greater than the supplied cable, the
installer must provide a terminated jumper cable from the box location to the cable end.
2. Splitter is only required for single awnings only. RF Receiver and Ignition Lockout may be directly connected to any open
"EYE" port for multiple awning configurations.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 10
WIRING DIAGRAM –2-AWNINGS
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR014a
Ignition Switched
+12VDC
12VDC
Ground Ignition
Lockout
Sensor
(Optional)
Sensor #1
Key Pad
Sensor #2
Awning #1
3
5
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
Wht
Blk
Grn
Wht
Blk
Grn
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
3 Conductor 14AWG
NM Wire w/ Gnd
Sensor
GRN
BLK
WHT
RED
Awning #2
Sensor
Remote
3
3 Conductor 14AWG
NM Wire w/ Gnd
DETAIL A
110VAC Power Line In
1
7
6
5
4
3
2
4
4
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 11
Green (Ground)
White
Red
Black
1Wire Legend:
2Awnings #1 & #4 shown as LH Motor, Awnings #2 & #3 shown as RH Motor
For LH Motor Configurations:
Motor Red goes to Pin (1); Motor Black goes to Pin (2)
For RH Motor Configurations:
Motor Red goes to Pin (2); Motor Black goes to pin (1)
3The SO cable from the 110VAC awning motor can only pass directly through a wall, it cannot be laid up
in the wall and must be connected to NM wire or individual wires in conduit no more than 6 inches past
the point of entry.
NOTES:
4
DR016a
5Wires for the Ignition Lock-Out Sensor are not pin specific.
The RF Reciever and the optional Ignition Lockout may be plugged into any open “EYE” port.
7
6
Cables are 4-wire RJ11 terminated phone cord (straight, no twist)
For screw type terminals: After testing connections, use Loctite 29005 or equivalent
to secure screws in terminal block.
8Terminal block designations are for reference only. Actual boards may not be marked.
Loctite
29005
Screw Type
Terminal Block
FROM TO (MOTOR #1) TO (MOTOR #2)
White 4 4
Black 5 5
AC Power Source
Ground 7 7
Black
Red Refer to Flag Note 2
White 3
Awning #1 Motor
Ground 6
Black
Red Refer to Flag Note 2
White 3
Awning #2 Motor
Ground
6
#1 Sensor 10’ Cable “AMD”
#2 Sensor 10’ Cable “AMD”
Key Pad 25' Cable DSK
RF Receiver 60” Cable "EYE" see note 4
Ignition Lockout 60“ Cable "EYE" see note 4
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 12
WIRING DIAGRAM –4AWNINGS
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RF
Receiver
GRN
BLK
WHT
RED
Key Pad
DR015a
Sensor #1
Key Pad
Sensor #2
Awning #1
3
4
4
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
Wht
Blk
Grn
Wht
Blk
Grn
2 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
RED
WHT
BLK
GRN
BLK
WHT
RED
GRN
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
AMDSUNAUXEYEDSK
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
1
7
6
5
4
3
2
To 110VAC
3 Conductor 14AWG
NM Wire w/ Gnd
To 110VAC
Sensor
GRN
BLK
WHT
RED Awning #2
Sensor
Remote
3
3 Conductor 14AWG
NM Wire w/ Gnd
GRN
BLK
WHT
RED
Sensor #3
Sensor #4
Awning #3
3
3 Conductor 14AWG
NM Wire w/ Gnd
Sensor
GRN
BLK
WHT
RED Awning #4
Sensor
3
3 Conductor 14AWG
NM Wire w/ Gnd
DETAIL A
110VAC Power Line In
(typical both boxes)
1
7
6
5
4
3
2
Ignition Switched
+12VDC
12VDC
Ground
Ignition
Lockout
Sensor
(Optional)
5
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 13
Green (Ground)
White
Red
Black
1Wire Legend:
2Awnings #1 & #4 shown as LH Motor, Awnings #2 & #3 shown as RH Motor
For LH Motor Configurations:
Motor Red goes to Pin (1); Motor Black goes to Pin (2)
For RH Motor Configurations:
Motor Red goes to Pin (2); Motor Black goes to pin (1)
3The SO cable from the 110VAC awning motor can only pass directly through a wall, it cannot be laid up
in the wall and must be connected to NM wire or individual wires in conduit no more than 6 inches past
the point of entry.
NOTES:
4
DR016a
5Wires for the Ignition Lock-Out Sensor are not pin specific.
The RF Reciever and the optional Ignition Lockout may be plugged into any open “EYE” port.
7
6
Cables are 4-wire RJ11 terminated phone cord (straight, no twist)
For screw type terminals: After testing connections, use Loctite 29005 or equivalent
to secure screws in terminal block.
8Terminal block designations are for reference only. Actual boards may not be marked.
Loctite
29005
Screw Type
Terminal Block
TO CONTROL BOARD
FROM MOTOR #1 MOTOR #2 MOTOR #3 MOTOR #4
White 4 4 4 4
Black 5 5 5 5
AC Power Source
Ground 7 7 7 7
Black
Red
Refer to Flag
Note 2
White 3
Awning #1 Motor
Ground 6
Black
Red
Refer to Flag
Note 2
White 3
Awning #2 Motor
Ground
6
Black
Red
Refer to Flag
Note 2
White 3
Awning #3 Motor
Ground
6
Black
Red
Refer to Flag
Note 2
White 3
Awning #4 Motor
Ground
6
#1 Sensor 10’ Cable “AMD”
#2 Sensor 10’ Cable “AMD”
#3 Sensor 10’ Cable “AMD”
#4 Sensor 10’ Cable “AMD”
Key Pad 25' Cable "DSK"
RF Receiver 60” Cable "EYE" see note 4
Ignition Lockout 60“ Cable "EYE" see note 4
Notes: 1. Splitter is used w/ Ignition Lock-Out only. If Lock-Out is not installed, connect the receiver directly to "EYE".
2. Cable lengths are the lengths of the furnished cables. If a connection requires a length greater than the supplied cable, the
installer must provide a terminated jumper cable from the box location to the cable end.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 14
CONNECTION FLEX W/"110VDR" CONTROL BOXES
The wiring diagrams show the standard installation for multiple awning configurations. For control boxes marked
w/ "110VDR", the installer may adjust the cable interconnections for greater flexibility during installation.
1. The key pad may be installed in the unused DSK port of any board with the jumper cables sequentially
connected from the AUX port to the DSK port of the next board.
Example: Placing the keypad in the DSK of Board 3.
Key Pad
CR024
AMDSUNAUXEYEDSK AMDSUNAUXEYEDSK AMDSUNAUXEYEDSK AMDSUNAUXEYEDSK
Motor 1 Motor 2 Motor 3 Motor 4
Figure 7. Alternate Cabling for 110VDR Boxes.
2. The RF Receiver and the optional ignition lock-out can be plugged into any unused "EYE" port. It is not
necessary to use the splitter as shown in the diagrams.
3. The "110VDR" control boxes are compatible with integrator interfaces. Contact Carefree engineering
for information and system requirements.
OPTIONAL MANUAL BYPASS SWITCH
Installers may elect to install a manual bypass switch for testing or
emergency operation of the awning. The simple switch allows the
operator to extend or retract the awning without using the keypad
control panel. For multiple awning installations, a separate switch
must be installed for each awning.
1. Open the control box and identify the terminal block next to the
phone cord jacks.
2. Connect the switch to the terminal block as shown in the
diagram.
The switch is a single pole, double throw, momentary ON, center
OFF. Components are installer furnished.
Common
Extend
Retract
Manual Switch
Single Pole, Double
Throw, Momentary ON,
Center OFF
DR011
Figure 8. Manual Bypass Switch.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 15
TESTING THE SYSTEM
All function buttons are press ON. The auto-functions continue until the awning is fully extended or
retracted. Pressing the button a second time will stop the function (does not apply to the "Extend All" or
Retract All" commands). It is not necessary to hold the button while the function is active.
1. While observing the control panel, have a second person initiate 110VAC power to the coach and
awning system. The following should occur:
1.1 The System Indicator and Sensitivity Level LEDs will briefly illuminate.
1.2 The system then goes to the default settings: The default settings are the last known state when
the AC power source was suspended. Example: If power was "ON" and the sensitivity was set to
"2", when AC power is applied, power will be on and sensitivity will be set to "2".
2. If ON press the POWER “OFF”. ALL LEDs should be extinguished. The POWER ON/OFF button disables all
functions including Auto-Retract and the RF remote. It does not disconnect the 110VAC power.
3. Check the extend function.
3.1 Press the POWER “ON.
3.2 Press the Awning #1 EXTEND button. The awning should extend.
3.3 Press the extend button again. The awning should stop
3.4 Press the extend button a third time. Observe the awning, it should fully extend. The system performs
an auto-tension action when the awning is fully extended. The awning rolls in reverse to tension the
fabric. The auto-tension feature works only with the extend function when the awning is fully extended.
4. Check the retract function.
4.1 Press the Awning #1 RETRACT button. The awning should retract.
4.2 Press the retract button again. The awning should stop
4.3 Press the retract button a third time. Observe the awning; it should fully retract to the closed position.
NOTE: If the awning moves in the opposite direction than the label, the red and black MOTOR
wires are reversed in the control box.
5. Repeat steps 3 and 4 for each of the Extend/Retract button combinations.
6. Test the mid-position functions. Press and release each mid position button (Slide-Out cover and Window).
The awning should extend or retract to the specified position.
7. Test the Auto-Retract function:
8.1 Fully extend awning #1.
8.2 Set the WIND SPEED to the lowest setting.
8.3 Create a firm but gentle vertical rocking motion with the leading edge of the awning. The awning should
retract after 2-3 seconds of the motion. The awning will retract to the slide-out position.
8. Repeat step 6 for each of the awnings.
9. If the optional Ignition Sensor is installed:
10.1 Partially retract the awning.
10.2 Turn the vehicle ignition key ON.
10.3 If the RTL lockout is installed, the awning(s) will retract.
10.4 Press the EXTEND button. The awning(s) should not extend.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 16
STANDARD SYSTEM ADJUSTMENTS
WARNING
NEVER ATTEMPT TO ADJUST OR ALTER THE MIDDLE RAIL AND ATTACHED COMPONENTS.NEVER ATTEMPT TO
MOVE OR ADJUST THE ARM KNUCKLES IN THE CASE OR ON THE MIDDLE RAIL;THESE HAVE BEEN PRE-SET AT THE
FACTORY FOR OPTIMUM OPERATION.THE FOLLOWING INSTRUCTIONS ARE THE ONLY INSTALLATION
ADJUSTMENTS AVAILABLE FOR THE PARAMOUNT AWNING SYSTEM.
SETTING THE MOTOR LIMITS
The motor limit switches are preset at the factory for best operation of the awning. The “OUT” limit switch is
used to stop the motor when the awning is fully extended. The “IN” limit switch is used to stop the motor
when the awning is fully retracted. The “IN” limit is NOT USED when the Direct Response system is installed.
“OUT” Limit Switch
4mm Allen Head
“IN” Limit Switch
4mm Allen Head
Paramount014
LH Motor RH Motor
Lead Rail
“OUT” Limit Switch
4mm Allen Head
“IN” Limit Switch
4mm Allen Head Increase
Decrease
Increase
Decrease
Figure 9. Motor Limit Switches.
The limit switches are located inside the case, near the end cap. To access the switches, remove the small
rubber plugs next to the end cap or end plate.
Adjusting the OUT Limit Switch
NOTE: During normal operation, the awning will extend out completely then roll back slightly to
provide tension to the fabric.
1. Extend the awning out completely.
2. Confirm that the arms are fully extended. The motor should stop and the fabric should be tight. If the
motor continues to run, the fabric will sag; or, if the motor quits before the arms are extended, it will be
necessary to adjust the “OUT” limit switch.
3. Using a 4mm Allen wrench turn the “OUT” limit switch. For LH motors, CLOCKWISE increases time the
motor runs during extension, COUNTERCLOCKWISE reduces the time the motor runs. For RH motors,
COUNTERCLOCKWISE increases time the motor runs during extension, CLOCKWISE reduces the time the
motor runs.
NOTE: It is best to make the adjustments in increments of a single turn. 3 full turns of the
screw equals approximately 2” of fabric extension.
4. Extend and retract the awning several times to confirm that the adjustment is correct.
5. Repeat steps 3 and 4 as required until the awning extends correctly.
Adjusting the IN Limit Switch
NOTE: The “IN” limit switch is not adjusted when the Direct Response system is installed. The system
electronics monitors the motor and shuts the motor off when the awning is fully retracted.
If the IN limit switch is accidentally adjusted, the motor may shut off before the awning is fully closed. If this occurs,
turn the IN adjustment screw clockwise. It is not necessary that the screw matches the closed position. The
electronics control the closed position.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 17
ADJUSTING THE LEAD RAIL
Adjusting the Lead Rail Height
The Paramount arms are installed and adjusted at the factory to operate at the tallest height possible. For multiple
awning installations, the lead rails of adjacent awnings may appear to not align because of installation variables.
The height of the high lead rail may be lowered with the procedure below. This is not a pitch adjustment.
Maximum height adjustment is approximately 3".
1. Fully extend the awnings.
2. On the middle rail, locate the long arm knuckle
closest to the adjacent awning.
3. Loosen the securing screws located on the outside
of the knuckle. DO NOT remove these screws.
4. Turn the adjustment screw counter clockwise to
lower the lead rail. Turn the screw in increments of
1/2 turn until the lead rail matches the adjacent
awning lead rail.
Tip: If the screw is hard to turn, have a second person lift up on the lead rail, then turn the screw and
let the lead rail down. Repeat until the lead rail is at the desired height.
5. Tighten the securing screws 30-33 ft-lbs.
Adjusting the Horizontal Lead Rail Position
The following procedure is to adjust the horizontal position of the lead rail when the rail is not centered in
the case when the awning is closed. This is only necessary if the end plate of the lead rail is rubbing or
hitting the end plate of the case.
B
DETAIL B
Lead Rail
Paramount022
Lead Rail
Connector
Set Screw
(2 per connector)
1/4” Approx.
Lead Rail
End Plate
DETAIL A
A
Figure 11. Adjusting the Lead Rail Horizontally.
1. (Detail A) With the awning closed as much as possible measure the distance between the inside of the case
end plate and the outside of the lead rail end plate. The distance should be approximately 1/4". Note the
difference between the actual measurement and the standard 1/4" spacing. This is the amount of adjustment
required.
Example: If the lead rail overlaps the end plate by 1/8", the difference is 1/8" + 1/4" = 3/8" difference.
2. Extend the awning out just past the slide-out position. The long arms should be slightly extended to
allow access to the lead rail connector.
3. Mark the location of the lead rail connectors for reference then loosen the setscrews that hold the
connectors in place.
4. Move the connectors the distance measured in step 1 and tighten the set screws.
NOTE: To adjust the lead rail in one direction, move the connectors in the opposite direction.
For example to shift the lead rail to the right, move the connectors to the left.
CAUTION
BOTH CONNECTORS MUST BE MOVED THE SAME DISTANCE AND DIRECTION.
5. Test by closing the awning. Repeat if necessary.
Long Arm (ref)
Adjustment Screw
Securing Screws
Middle Rail (ref)
Paramount013
Figure 10. Lead Rail Height Adjustment.
Table of Contents

Carefree of Colorado Installation Manual PARAMOUNT
052548-001r1 18
MANUAL OVERRIDE
If 110V power is not available to the coach, the Paramount awning can still be safely retracted using the
manual override.
7mm Hex
Manual Override
7mm Hex
Manual Override
RTA015a
LH Motor RH Motor
Lead Rail
Open (RH Motor)
Close (RH Motor)
Open (LH Motor)
Close (LH Motor)
Figure 12. Manual Override Access.
1. The bypass is located inside the case, near the end cap. Remove the large rubber plug on top of the
awning located toward the rear of the case on the motor side.
2. Chuck the 7mm hex key into a 3/8” battery powered drill.
3. Insert the hex key into the manual override on the awning.
4. Operate the drill in the direction shown in the diagram to close the awning. Reverse the drill to open
the awning.
5. When done, reinsert the rubber plug.
NOTES:
Table of Contents