Carefree LATITUDE User manual

070005-301r5 Printed in USA November, 2018
S ERVICE M ANUAL
LATITUDE
12V Motorized Lateral Arm Awning w/ Direct Response
Read this manual before servicing or using this product. Failure to follow the instructions
and safety precautions in this manual can result in personal injury and/or cause the
product to not operate properly.
For LED replacement parts and service procedures refer to 052584-301 “LED Service Manual for
Vertical Arms” available on-line at www.carefreeofcolorado.com

TABLE OF CONTENTS
Standard System Adjustments ....................................................................................................1
Adjusting the Arm Position......................................................................................................................1
Adjusting the Pitch..................................................................................................................................1
Canopy Replacement....................................................................................................................2
Removing the Head Covers..........................................................................................................4
Removing the Covers..........................................................................................................................4
Attaching the Covers...........................................................................................................................4
Roller Tube Service.......................................................................................................................5
Arm Replacement..........................................................................................................................6
Gas Spring Replacement..............................................................................................................7
RH (Motor) Arm Spring...........................................................................................................................7
LH (Idler) Arm Spring..............................................................................................................................7
Replacing the Mounting Plate ......................................................................................................8
Motor/Gearbox Replacement........................................................................................................9
Sensor/Control Module Replacement........................................................................................ 10
Wiring Diagram............................................................................................................................11
Switch and Control Module...............................................................................................................11
Standard Maintenance................................................................................................................12
Fabric Care...........................................................................................................................................12
Mildew...............................................................................................................................................12
Pooling..............................................................................................................................................12
Hardware Maintenance.....................................................................................................................12
Motor Maintenance...............................................................................................................................12
Part Number Listing....................................................................................................................13
Part Number/Serial Number Location...................................................................................................13
Single Stage Latitude Illustrated Parts List...........................................................................................13
Dual Stage Latitude Illustrated Parts List..............................................................................................15

P ROPRIETARY S TATEMENT
The Latitude Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The
information contained in or disclosed in this document is considered proprietary to Carefree of Colorado.
Every effort has been made to ensure that the information presented in the document is accurate and
complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result
from the use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the
title page. Earlier model configurations may differ from the information given. Carefree of Colorado
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual,
without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado
products only. Any other reproduction or translation of this document in whole or part is strictly prohibited
without prior written approval from Carefree of Colorado.
S AFETY I NFORMATION
This is the safety alert symbol. It is used to alert individuals to potential
personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible personal injury or death.
WARNING
Indicates a hazardous situation, which if not avoided, could result in death or
serious bodily injury.
CAUTION
Indicates a hazardous situation, which if not avoided, may result in minor or
moderate bodily injury.
NOTICE
Indicates a situation that may result in equipment-related damage.
General Safety:
WARNING This product can expose you to chemicals including Di-isodecyl phthalate
(DIDP), Vinyl Chloride and Formaldehyde, which are known to the state of California to cause
cancer or birth defects or other reproductive harm. For more information visit
www.P65warnings.ca.gov
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
WARNING Always wear appropriate safety equipment (i.e. goggles).
CAUTION Always use appropriate lifting devices and/or helpers when lifting or
holding heavy objects.
NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and
aluminum can be "stripped out" and lose the ability to grip and hold.
Carefree of Colorado www.carefreeofcolorado.com a Scott Fetzer com
p
an
y

PRODUCT OVERVIEW
The Latitude Awning is a state of the art lateral arm awning. Each unit is equipped with lateral support arms. No
vertical arms interfere with coach sidewalls, custom graphics or equipment mounted on the sidewalls.
Fully retractable and self-storing;
Available in two configurations: single stage or dual stage;
The awning motor operates on standard 12VDC (range 10VDC to 14VDC);
Single touch operation for extend and retract;
Direct Response is standard;
LED lights standard, mounted in roller tube;
SPECIFICATIONS
Length Single Stage 10' 4" – 20' [3.15m – 6.1m]
Dual Stage 10' 4" – 18' [3.15m – 5.49m]
Support: Lateral Spring Arms
Motor: Power: 10VDC–14VDC Circuit Rating: 15 amp
(motor is mounted in RH roller tube head)
Power Source: Motor and controls are routed and hardwired into the vehicle’s 12V system
Controls: Carefree Direct Response
Color: Hardware: White or Black
Fabric: Heavy Duty Vinyl with Weatherguard or FLXGuard
(refer to sales literature for colors and options)
Weight: 10' 4" 12' 14' 16' 18' 20'
Single Stage 45.5 lbs. 48.3 lbs. 51.7 lbs. 55.0 lbs. 58.3 lbs. 61.6 lbs.
Dual Stage 52.1 lbs. 55.9 lbs. 60.4 lbs. 65.0 lbs. 69.6 lbs. n/a
Original Mounting Plate Configuration
Current Mounting Plate Configuration
12.75"
5.6"
6.1"
12.75"
5.6"
Awning Length
Awning Length + 3.9" 1.2"
2.7"
7"
FL002
12.25"
5.7"
6.1"
13.75"
5.7"
Awning Length
Awning Length + 2.6"
1.3"
1.3"
7"
FL002b

Carefree of Colorado Service Manual LATITUDE
070005-301r5 1
STANDARD SYSTEM ADJUSTMENTS
ADJUSTING THE ARM POSITION
For the awning to operate and close correctly, the arms must be parallel to the roller tube. If the arm sags,
the arm position can be adjusted to bring the arm parallel.
1. Open the awning 2"-3" to access the
adjustment screws located on the side of
the arm knuckle at the wall.
2. Loosen the upper screw (counterclockwise).
3. Tighten (clockwise) the lower screw to
raise the arm elbow.
NOTE: Make adjustments in quarter turn increments.
Tip: Lift the arm at the elbow while tightening the lower screw.
4. Repeat steps 2 and 3 until the arm is parallel with the roller tube.
5. Tighten the upper screw.
ADJUSTING THE PITCH
The awning pitch can be adjusted. It is strongly recommended that adjustments be made in small
increments to achieve the desired setting.
This procedure works best with 2 people, one person to lift the roller tube to relieve the weight and one
person to make the adjustments.
DO NOT USE POWER TOOLS,ALWAYS USE HAND TOOLS TO MAKE ADJUSTMENTS.
1. Open the awning.
2. At the top of the knuckle loosen the
locking screw approximately 1/4".
NOTICE The locking screw MUST be
loosened before adjusting the pitch.
3. To raise the pitch: Turn the lower
adjustment screw clockwise.
4. To lower the pitch: Turn the lower adjustment screw counterclockwise.
5. Hand tighten the locking screws until snug when the desired pitch is achieved.
NOTICE DO NOT overtighten the locking screw. Overtightening the screw can cause unnecessary
strain and wear on the knuckle.
NOTE: After the initial installation and the awning is opened, the awning may settle. This is normal.
Check that the locking screws on the knuckle are snug.
Raise FL013
Adjustment
Screws
Adjust Arm to be
Parallel to Roller Tube
FL009a
Locking Screw
RaiseLowerRaiseLower
Locking Screw
Adjustment Screw Adjustment Screw

LATITUDE Service Manual Carefree of Colorado
2 070005-301r5
CANOPY REPLACEMENT
1. Extend the awning completely.
2. Firmly tie the elbows of the spring arms together. Use a
minimum 1/2" rope - do not use bungee cords. When
tying the rope, use a non-slip knot such as a square knot
or equivalent.
CAUTION Failure to secure the arms will
allow the spring arms to extend possibly causing
personal injury and damage to the awning.
3. Over extend the awning to align the fabric slot with the
cutout on the idler side. This will cause slack in the fabric.
4. Disconnect Power.
CAUTION When the power is on, the direct
response system is active. Movement during this
procedure can cause the awning to attempt to close
unexpectedly.
5. At the roller tube:
5.1. Remove the fabric retaining screws and plastic
washers (quantity of 2 ea).
5.2. On the motor side, remove the split grommet from
the roller tube. Carefully pull the wires and
connectors out of the tube and disconnect.
6. At the awning rail, cut the LED harness close to the
canopy. Clamp the harness going into the vehicle to
prevent it from falling in the wall.
7. For canopies with QuicKonnect:
7.1. Remove the fabric retaining screws from the
QuicKonnect (a & b).
7.2. Remove one retaining screw from the awning rail (c).
7.3. Slide the QuicKonnect from the awning rail and
canopy.
7.4. Slide the canopy out of the roller tube.
7.5. Slide the new canopy into the roller tube and center.
7.6. At the reinforcements in the canopy, secure the fabric
to the roller tube with the retaining screws and
wahsers removed previously.
7.7. Slip the fabric funnel onto the QuicKonnect.
7.8. While holding the fabric, simultaneously slide the
QuicKonnect into the awning rail and over the canopy.
7.9. Remove the funnel from the QuicKonnect.
7.10. Place one (1) #6 x 3/8" screw (c) through the awning rail outside the end of the QuicKonnect (not
through the QuicKonnect).
8. For canopies without QuicKonnect:
8.1. Remove the fabric retaining screws from the awning rail.
8.2. Slide the canopy out of the roller tube and awning rail.
8.3. Slide the new canopy into the roller tube and awning rail and center in the roller tube.
Spring Arms
Firmly Tie Elbows Together
Retaining Screw
and Washer
Retaining Screw
and Washer
Align Fabric Slot with
Cutout on Idler Head
Grommet
LED Harness
Canopy
Harness
FL016
#6 x 3/8"
Screw (x4)
(a)
(c)
(b)
QuicKonnect Fabric
Awning Rail
Funnel
QuicKonnect
Fabric
Awning Rail

Carefree of Colorado Service Manual LATITUDE
070005-301r5 3
8.4. At the reinforcements in the canopy, secure the fabric to the roller tube with the retaining screws
removed previously.
9. While firmly pressing the roller tube, remove the arm ties. Slowly allow the roller tube and arms to extend.
10. Restore power.
11. Retract the awning and check that the canopy is rolling up squarely onto the roller tube. Adjust as
necessary.
12. Place one (1) #6 x 3/8" screw (a) through the QuicKonnect (or awning rail if the QuicKonnect is not
used), fabric and polyrod approximately 1" in from the fabric edge
13. On the opposite side, pull the fabric tight then place one (1) #6 x 3/8" screw (b) through the
QuicKonnect (or awning rail if the QuicKonnect is not used), fabric and polyrod approximately 1" in from
the fabric edge.
14. Connect the LED harness:
14.1. At the roller tube, connect the canopy harness connector and LED connector. Then carefully
push the connectors into the roller tube.
14.2. Place the split grommet over the canopy harness and press the grommet into the hole of the
roller tube.
14.3. At the vehicle wall, route the new canopy harness through the wall to the switch.
Tip: Tie the new harness to the old harness that was cut previously. Use the old harness to pull
the new harness through the wall to the desired location.
14.4. At the vehicle wall, provide some slack between the canopy and wall. Seal the wall entrance
hole and harness with a quality silicone sealant.
14.5. Connect the new harness to the switch. Two (2) .187, 18-24 awg female disconnects are provided if
connecting to a switch.
14.6. Alternate method: At the wall, splice the new harness to the existing harness using 24 awg butt
connectors. Push the connectors into the vehicle wall. Seal the wall entrance hole and wires
with a quality silicone sealant.
NOTE: Be sure to allow enough harness from the canopy to provide some slack for the harness
and adequate length for the connectors to be pushed inside the wall before sealing the hole and
harness with a quality silicone sealant.

LATITUDE Service Manual Carefree of Colorado
4 070005-301r5
REMOVING THE HEAD COVERS
These instructions are for removing the head covers for service or replacement.
The illustration shows the motor head covers. The instructions apply to both the motor and idler head.
NOTE: If replacing the covers: To ensure that the covers properly match up and latch together always
replace both the front and rear cover. Replacement kits include both the front and rear covers and
attaching hardware.
1. Extend the awning to access the screws in the back cover of the head assembly.
2. Disconnect power.
CAUTION WHEN THE POWER IS ON,THE DIRECT RESPONSE SYSTEM IS ACTIVE.MOVEMENTS
DURING THIS PROCEDURE CAN CAUSE THE AWNING TO CLOSE UNEXPECTEDLY.
Removing the Covers
3. Remove the front cover. The cover snaps onto the
rear cover. To remove, press the bottom of the rear
cover until the front cover releases then rotate and lift
the front cover off.
4. For the motor side: Slide the sensor module out of the
rear cover. It is not necessary to disconnect the wires.
Carefully allow the module to hang down.
5. Remove the screws and bumper from the rear cover
and remove the rear cover.
Attaching the Covers
6. Attach the rear cover.
7. For the motor side: Slide the sensor module into the
rear cover. Tuck the wires inside the cover.
8. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks.
Front
Cover
Slide Module Out
FL029
Press Up On Rear Cover
to Release Front Cover
Rear
Cover

Carefree of Colorado Service Manual LATITUDE
070005-301r5 5
ROLLER TUBE SERVICE
When service requires removing the Latitude roller tube it is important that the roller tube is correctly
attached when reinstalled.
For models made prior to date code 6293 (10-19-2016), the shaft of the roller tube end plug on the motor
side has two (2) grooves for attaching e-clips. The e-clips must be placed in the correct grooves for the
roller tube attachment.
NOTICE Failure to properly attach the roller tube as shown below can cause unwanted
movement of the roller tube causing damage to the awning and making the awning not function
correctly.
On the idler side: The e-clip
must be placed in the outer
groove of the end plug shaft.
On the motor side: The e-clip
must be placed in the inner
groove of the end plug shaft.
NOTE: On units made after the
date code, the shaft has only one
(1) groove for the e-clip.
A replacement roller tube attach
kit (R001848) is available to
replace lost or damaged
attachment hardware.
NOTE: Early units used a round e-clip and washers on the idler side. The
e-clip with tab shown above replaces the washers and round e-clip. The
replacement roller tube attach kit includes the e-clip with tab.
FL033
Front
Cover
E-Clip
Roller
Tube
Front
Cover
E-Clip
Roller
Tube
Inner Groove
Retaining
Clips (x2)
Outer Groove
Inner Groove
Outer Groove
Roller Tube
Roller Tube
End Plug
End Plug
IDLER SIDE MOTOR SIDE
FL034
Retaining
Clips (x2) IDLER SIDE
Replaces Washers
and Round E-Clip

LATITUDE Service Manual Carefree of Colorado
6 070005-301r5
ARM REPLACEMENT
These procedures apply to both the left and right arms. Differences are noted where required.
CAUTION The arm is under tension to open. Use extreme care to firmly hold the arms
during assembly and disassembly to avoid any sudden or unexpected movement by the arm.
Serious personal injury and/or property damage could occur.
NOTICE When detached, do not allow the roller tube and/or middle rail to drop toward the
ground. the twisting motion can damage the opposite arm and awning. Use a scaffold or similar
device to support the roller tube and middle rail.
1. Over extend the awning.
2. DISCONNECT POWER.
3. For Two-Stage Latitude: Loosen the retaining screw in
the glide above the arm elbow. Lift the middle rail off the
elbow pin. Provide support for the middle rail.
4. For the motor side arm: Carefully pull the control cable from
the slot at the top of the arm channels. It is not necessary to
disconnect the cable from the motor or wall.
5. At the roller tube:
5.1. Remove the front cover. The cover snaps onto the rear
cover. To remove, press the bottom of the rear cover to
release the front cover.
5.2. Remove the E-Clip that holds the rotation pin.
5.3. Provide support for the roller tube.
5.4. Firmly hold the arm and remove the rotation pin. Pull
the arm out and allow the arm to extend out below the
roller tube. Support the arm.
6. At the wall connection:
6.1. Loosen the setscrew and remove the rotation pin.
6.2. Pull the arm from the knuckle and set aside.
7. Using two people firmly hold the new arm assembly and
remove the shipping ties. Allow the arm to slowly open to
its maximum extension.
CAUTION When the arm is closed, it can open
with significant force. Use care when opening.
8. Lift the new arm and attach to the wall knuckle with the rotation pin and set screw removed previously.
Ensure that the groove in the pin is in line with the screw hole.
9. At the roller tube:
9.1. Fold the arm as necessary and align the arm with the mounting holes.
9.2. Insert the rotation pin. Ensure that the pin is oriented with the groove down.
9.3. Secure the pin with a new e-clip between the arm knuckle and lower attach bracket ear. Ensure
that the clip is in the groove of the pin.
9.4. Attach the front cover.
10. For the motor side arm: Carefully press the control cable into the slot at the top of the arm channels.
Allow some slack at the joints and elbows to allow the cable to flex when the awning is operated.
11. For Two-Stage Latitude: Press the middle rail glide onto the elbow pin. Tighten the securing screw
loosened previously.
12. To align the arm. Refer to "Adjusting the Arm Position" on page 1.
13. To adjust the arm pitch. Refer to "Adjusting the Pitch" on page 1.
Set Screw Rotation
Pin
E-Clip
Rotation
Pin
Front
Cover
Middle Rail
Glide
Retaining Screw
Control
Cable
Control
Cable
Middle Rail
Roller Tube
Vehicle Wall
FL023
Elbow Pin

Carefree of Colorado Service Manual LATITUDE
070005-301r5 7
GAS SPRING REPLACEMENT
NOTICE The gas spring clevises must be oriented and installed as shown. Failure to orient
the clevises correctly can cause the arms to not function correctly.
NOTICE When detaching the roller tube, do not allow the roller tube to drop toward the ground.
the twisting motion can damage the opposite arm. Use a scaffold to support the roller tube.
1. Fully extend the awning.
2. DISCONNECT POWER.
RH (MOTOR)ARM SPRING
1. Remove the front cover. To remove, press the bottom of the rear cover to release the front cover.
2. Remove the E-clip from the roller tube shaft.
3. While firmly holding the arm, slide the motor head off the
roller tube shaft. Provide support for the roller tube.
4. Slowly allow the arm to extend fully. Provide support for
the end of the arm.
5. Remove the old spring in the following order:
5.1. Unclip the cylinder clevis from the upper bracket.
5.2. Unhook the rod clevis from the lower bracket.
6. Install the new spring in the following order:
6.1. Hook the rod clevis around the lower bracket post.
6.2. Clip the cylinder clevis onto the upper bracket post.
7. Fold the arm to align the roller tube shaft with the motor
head. It may be necessary to twist the roller tube to align
the flats of the shaft with the motor hole.
8. Secure the roller tube shaft with a new e-clip. The e-clip goes
in the INNER groove of the roller tube shaft. Refer to page 5.
9. Reattach the front cover.
LH (IDLER)ARM SPRING
1. Remove the front cover. To remove, press the bottom of
the rear cover to release the front cover.
2. Remove the e-clip and retaining clips (and washers if
installed) from the roller tube shaft.
3. While firmly holding the arm, slide the idler head off the
roller tube shaft. Provide support for the roller tube.
4. Slowly allow the arm to extend fully. Provide support for
the end of the arm.
5. Remove the old spring in the following order:
5.1. Unclip the rod clevis from the lower bracket.
5.2. Unhook the cylinder clevis from the upper bracket.
6. Install the new spring in the following order:
6.1. Hook the cylinder clevis around the upper bracket post.
6.2. Clip the rod clevis onto the lower bracket post.
7. Fold the arm to align the roller tube shaft with the idler head.
8. Secure the roller tube shaft with a new E-clip. The e-clip goes
in the OUTER groove of the roller tube shaft. Press the
retaining clips over the end of the shaft close to the E-clip.
9. Reattach the front cover.
Remove 1
st
Attach 2
nd
FL021
Clevises Must Be Oriented
and Installed As Shown
Motor Side
Clevises Must Be Oriented
and Installed As Shown
Idler Side
Lower
Bracket
Upper
Bracket
Remove 2
nd
Attach 1
st
Lower
Bracket
Upper
Bracket
Remove 1
st
Attach 2
nd
Remove 2
nd
Attach 1
st
Front
Cover
E-Clip
Roller
Tube
Inner Groove
Front
Cover
E-Clip
Roller
Tube
Retaining
Clips (x2)
Outer Groove

LATITUDE Service Manual Carefree of Colorado
8 070005-301r5
REPLACING THE MOUNTING PLATE
This procedure requires two people. The illustrations show
the RH plate. The procedure is the same for the LH plate.
1. Open the awning 18"-24". This is to allow adequate
room for tools and access to the mounting plate.
2. Disconnect power.
3. Do not remove the bottom inner screw and the outer
upper screw marked with * in the illustration. Remove
the rest of the plate fasteners and set aside.
4. On the side being repaired:
4.1. Collapse the arm. Leave a space between the arm
and plate to access the set screw in later steps.
4.2. Securely tie the arm channels together with zip
ties. The ties should be close to the head.
5. Have a second person hold and support the roller tube
and arm at the arm elbow.
6. For the motor side mounting plate:
NOTICE If replacing the plate on the motor side, use care to not pull or damage the cable.
6.1. If the motor cable is routed into the vehicle outside of the plate: Partially remove the wire from the
top of the arm channel to provide adequate slack to move the cable out of the way.
6.2. If the motor cable and LED harness are routed through a hole in the plate: Pull some slack cable
out of the wall and cut the wires. It will be necessary to splice the wires together after the new
plate is installed.
7. Remove the two remaining screws in the mounting plate and rotate the arm and plate away from the wall.
8. Loosen the set screw and remove the rotation pin that attaches the arm to the plate. Set plate aside.
9. Attach the arm to the new plate using the rotation pin removed previously. Tighten the set screw to
secure the pin.
10. Using the existing mounting holes in the wall, attach the new plate to the wall with a minimum of 2
screws in the bottom inner screw position and the outer upper screw position.
11. Remove the arm ties and allow the roller tube to slowly extend out.
CAUTION Firmly hold the arm while removing the ties. When the arm is closed, it can open
with significant force.
12. Install the remaining plate fasteners.
13. For the motor side mounting plate:
13.1. If the motor cable is routed into the vehicle outside of the plate: Insert the motor cable into the
groove in the top of the arm channel.
13.2. If the motor cable and LED harness are routed through a hole in the plate: Use appropriate sized
butt connectors to attach motor cable and LED wires that were cut previously. Be sure to match
the wire colors.
Wire Wire Gauge Butt Connector Size
Red and Black LED wires 24awg 22-24 awg
Red and Black Power 16awg 14-16 awg
Brown, Yellow and Gray 20awg 18-22 awg
13.3. Push the connectors into the wall and seal the hole with a quality silicone sealant.
14. Check that the arm is properly aligned with the roller tube. Refer to "Adjusting the Arm Position" on page 1.
15. Extend the awning and check the pitch. To adjust the arm pitch refer to "Adjusting the Pitch" on page 1.
Set Screw
Rotation
Pin
Control
Cable
FL026
Mounting
Plate
Fasteners (x9)
* Remove these fasteners last from old plate;
Attach these fasteners first with new plate
Tie Arm Together
4"

Carefree of Colorado Service Manual LATITUDE
070005-301r5 9
MOTOR/GEARBOX REPLACEMENT
9. Extend the awning a minimum of 18" to access the screws in the back cover of the motor side head
assembly.
10. Disconnect Power.
CAUTION When the power is on, the direct response system is active. Movements
during this procedure can cause the awning to attempt to close unexpectedly.
11. Press the roller tube toward the vehicle until the fabric becomes slack.
12. Firmly tie the elbows of the spring arms together. Use a minimum 1/2" rope - do not use bungee cords.
When tying the rope, use a non-slip knot such as a square knot or equivalent.
CAUTION Failure to secure the arms as described will allow the spring arms to extend
when the motor is detached possibly causing personal injury and damage to the awning.
13. Remove the front cover. The cover snaps onto the rear cover. To remove, press the bottom of the rear
cover until the front cover releases then lift the front cover off. Set part aside.
14. Slide the sensor module out of the rear case. Disconnect the wires attached to the motor and allow the
sensor to hang down on the remaining wires.
15. Remove the screws and bumper from the rear cover and remove the rear cover. Set parts aside.
16. Remove the motor mounting screws and set aside.
17. Slide the motor and gearbox off of the roller tube shaft. Separate the motor and gearbox.
18. Align the gearbox and new motor and insert the motor mount screws through both.
19. Align the gearbox with the roller tube shaft and attach the gearbox and motor with the mounting screws.
NOTE: It may be necessary to twist the roller tube to align the flats of the shaft with the hole in the gearbox.
20. Attach the motor wires from the module to the motor. Black goes to the top connection, Red goes to
the bottom connection.
21. Attach the rear cover.
22. Slide the sensor module into the rear cover.
23. Snap the front cover onto the rear cover. Hang the cover on the top and swing down until it clicks.
24. Hold the roller tube and remove the ties around the arms. Allow the roller tube to extend out slowly.
25. Restore power and test.
Spring Arms
Firmly Tie Elbows Together
Front
Cover
Motor
Sensor
Rear
Cover
Motor Wires
Top= Black; Bottom = Red
Roller Tube
Shaft
Motor Mount
Screws (x3)
Red
Black
Gearbox
FL018

LATITUDE Service Manual Carefree of Colorado
10 070005-301r5
SENSOR/CONTROL MODULE REPLACEMENT
This procedure may be done with the awning open or closed.
1. Disconnect power to the awning.
2. Remove the front cover. The cover snaps onto the rear
cover. To remove, press the bottom of the rear cover until
the front cover releases then lift the front cover off. Set part
aside.
3. Slide the sensor module out of the rear case. Disconnect
the wires to the module.
4. Connect the motor and cable wires to the new module.
Make sure to match the wire colors.
5. Slide the new module into the rear cover and tuck the wires.
6. Snap the front cover onto the rear cover. Hang the cover on
the top and swing down until it clicks.
7. Restore power and test.
Front Cover
Module
FL019
Wires to
Motor
Cable to
Module

Carefree of Colorado Service Manual LATITUDE
070005-301r5 11
WIRING DIAGRAM
Switch and Control Module
On/Off
Extend/Retract
Rear View of
Switch Assy
FL004
Control Module
(mounted in
motor head)
Gray
Yellow
Brown
Red
Black
Red
Black
FF
Awning
Red
Black
(Extend)
(Common)
(Retract)
(+12Vdc switched)
(Ground)
MF
MF
FM
FM
MF
MF
MF
F
M
Chassis Ground
.25, 14-16awg
Spade Terminals
1 Male, 1 Female
To +12VDC
.187, 14-16awg Female
Spade Terminals (qty: 2)
.187, 18-20awg
Female Spade
Terminals (qty: 3)
Additional
Extend/Retract
Switch
Gray
Yellow
Brown

LATITUDE Service Manual Carefree of Colorado
12 070005-301r5
STANDARD MAINTENANCE
Maintaining a Carefree Awning is easy. Just follow these basic steps:
Always operate the awning according to the instructions.
Periodically check that the fasteners are tight. Tighten if necessary.
Keep the awning fabric and arms clean.
FABRIC CARE
NOTICE Do not use oil based cleaners or any caustic, granulated, or abrasive type cleaners
on your Carefree product.
1. One of the best ways to keep the fabric looking good and to delay the need for deep or vigorous
cleanings is to hose fabrics off on a monthly basis with clear water. This practice will help prevent dirt
from becoming deeply imbedded in the fabric. In most environments, a thorough cleaning will be
needed every two to three years.
16. When it’s time for a thorough cleaning, the fabric can be cleaned while still on the awning frame.
For Vinyl Fabric – Use a soft brush and warm water with soap.
For Acrylic Fabric – Use a stiff brush and warm water with soap.
17. When cleaning the fabric, it is important to observe the following:
Always use a natural soap, never detergent.
Water should be cold to lukewarm, never more than 100F.
Air-dry only. Never apply heat to the fabric.
Always allow the fabric to dry thoroughly before rolling up the awning.
Mildew
Mildew is a fungus growth that looks like dirt. Vinyl coated polyester fabrics are mildew resistant because
of a chemical biocide in the vinyl coating. Under ordinary conditions, mildew will not appear. However, in
areas where high temperature and humidity are common, mildew can be a problem and required the
material to be washed more frequently. Thoroughly rinse the fabric with clean water and allow to air dry
completely before rolling up the awning.
Pooling
When water collects on the top of the fabric, this is known as "pooling". This can occur during inclement
weather or if a running air conditioner discharges over the awning. The water is dumped when the awning
is retracted. It is recommended that if water accumulates on the top; retract the awning in steps (8"-12") to dump
the water. This will help prevent the fabric from stretching or distorting.
The effects of wind and rain on an awning are unpredictable. Severe damage to the awning and the
vehicle may result. IF WIND OR EXTENDED PERIODS OF RAIN ARE EXPECTED,ROLL UP THE AWNING AND SECURE
FOR TRAVEL.
Hardware Maintenance
Replace any parts that become damaged.
Periodically check all mounting hardware, screws, lags, etc., and re-tighten when necessary.
MOTOR MAINTENANCE
Check all wiring and connections for wear. Repair when needed.
Check that the sealant is providing a good seal and no water is accumulating on the wiring.

Carefree of Colorado Service Manual LATITUDE
070005-301r5 13
PART NUMBER LISTING
PART NUMBER/SERIAL
NUMBER LOCATION
SINGLE STAGE LATITUDE ILLUSTRATED PARTS LIST
1
3
3
8
57
9
10
4
4
11 12
13
13
15
15
16
16 17
18
18 20
21
19
6
2
Original
Current
14
14
4
2
24
25
FL501
22
19a
19b
20a
20b
RETRACT
ON
EXTEND
OFF
AwningControl
RETRACT
ON
EXTEND
Awning Control
OFF
FL012
This awning is designed to provide many years of safe and reliable Carefree service
when operated and maintained according to the instructions in the owner’s manual.
For Awning Operation, Canopy Care & Warranty Coverage Refer to the Owner’s Manual
Need a copy of your manual or product warranty? Available on-line at
www.carefreeofcolorado.com
053661-001
US and International
Patents Pending
Carefree LATITUDE
Carefree
Sn : 1234567890
Pn : 123456789X
Dt : 1234
or go to www.e-carefree.com/sn
Serial Label
Roller Tube (ref)

LATITUDE Service Manual Carefree of Colorado
14 070005-301r5
Item Part Number Description Notes
1 R001782-xxx Roller Tube Assy 2
2 R001848 Roller Tube Attach Kit pkg of 2 clips and retaining rings 5
3 R001783-00X Cover Kit, Motor
4 R001798 Bumper
5 R001784 Motor Assy
6 R001810 Gearbox Assy
7 R060686-003 Sensor/Control Module, Direct Response
8 R012659-001 Motor Bracket
9 R001785-00X Cover Kit, Idler
10 R012660-001 Idler Bracket
11 R001786-10X Arm Assy, LH, Single Stage 3
12 R001787-00X Arm Assy, RH, Single Stage 3
13 R001788 Gas Spring, Latitude Single Stage
14 R040905-001 Hook, Gas Spring pkg of 2
15 R001789 Support, Gas Spring pkg of 2
16 R001823 Barrel, used on Single Stage Only pkg of 2
17 R001790 Cable Retainer used on Single Stage Only
18 R001791 Arm Attach Kit One Arm 3
19a R019376-20X Mounting Bracket Assy, LH Original 4
19b R019397-00X Mounting Bracket Assy, LH Current 4
20a R019376-30X Mounting Bracket Assy, RH Original 4
20b R019397-10X Mounting Bracket Assy, RH Current 4
21 R001792-xxx QuicKonnect
22 R040925-001 Canopy Funnel
23 R060703-00X Cable Assy, 5 Conductor not shown
24 R019468-006 Switch Kit
25 SR0115 Bezel Cover Kit
26 Canopy Only Refer to Canopy Order Form
27 R019886-005 Screw Pack, 1/4-20 x 1" Self-drilling, White not shown
R019886-006 Screw Pack, 1/4-20 x 1" Self-drilling, Black not shown
28 R019886-007 Screw Pack, 1/4 x 2" Lag, White not shown
R019886-008 Screw Pack, 1/4 x 2" Lag, Black not shown
Notes: 1. 0X = Color = 05 – White, 06 – Black; xx = Length
2. Roller tube (item 1) is complete with end bushings, LED strip
3. Arm Assemblies (items 11, 12) includes items 4, 13, 14, 15 and 16. Does not
include attaching pins. For attach pins order item 18 (1 kit per arm).
4. Original and current mounting brackets are not interchangeable.
Replacement brackets must match the existing brackets. Original brackets
can be identified by the 3 hole pattern beside the knuckle.
5. The roller tube e-clips w/ tab replace the previous round e-clips and the push
nuts and washers used on the idler side.
For LED replacement parts and service procedures refer to 052584-301 “LED Service Manual for
Vertical Arms” available on-line at www.carefreeofcolorado.com
Replaces Washers,
and Round E-Clip
FL030

Carefree of Colorado Service Manual LATITUDE
070005-301r5 15
DUAL STAGE LATITUDE ILLUSTRATED PARTS LIST
FL502
1
34
5
6
9
10
4
4
11 12
13
13
15
15
16
16
17
17
19
18
20
21
22
7
18a
18b
19a
19b
2
Original
Current
14
14
2
3
8
24
25
RETRACT
ON
EXTEND
OFF
AwningControl
RETRACT
ON
EXTEND
Awning Control
OFF

LATITUDE Service Manual Carefree of Colorado
16 070005-301r5
Item Part Number Description Notes
1 R001782-xxx Roller Tube Assy 2
2 R001848 Roller Tube Attach Kit pkg of 2 clips and retaining rings 5
3 R001783-00X Cover Kit, Motor
4 R001798 Bumper
5 R001784 Motor Assy
6 R001810 Gearbox
7 R060686-003 Sensor/Control Module, Direct Response
8 R012659-001 Motor Bracket
9 R001785-00X Cover Kit, Idler
10 R012660-001 Idler Bracket
11 R001793-10X Arm Assy, LH, Dual Stage 3
12 R001794-00X Arm Assy, RH, Dual Stage 3
13 R001795 Gas Spring, Latitude Dual Stage
14 R040905-001 Hook, Gas Spring pkg of 2
15 R001789 Support, Gas Spring pkg of 2
16 R001796 Ramp, Midrail pkg of 2
17 R001791 Arm Attach Kit One Arm 3
18a R019376-20X Mounting Bracket Assy, LH Original 4
18b R019397-00X Mounting Bracket Assy, LH Current 4
19a R019376-30X Mounting Bracket Assy, RH Original 4
19b R019397-10X Mounting Bracket Assy, RH Current 4
20 R001797-XXX-xxx Middle Rail Assy
21 R001792-xxx QuicKonnect
22 R040925-001 Canopy Funnel
23 R060703-00X Cable Assy, 5 Conductor not shown
24 R019468-006 Switch Kit
25 SR0115 Bezel Cover Kit
26 Canopy Only Refer to Canopy Order Form
27 R019886-005 Screw Pack, 1/4-20 x 1" Self-drilling, White not shown
R019886-006 Screw Pack, 1/4-20 x 1" Self-drilling, Black not shown
28 R019886-007 Screw Pack, 1/4 x 2" Lag, White not shown
R019886-008 Screw Pack, 1/4 x 2" Lag, Black not shown
Notes: 1. 0X = Color = 05 - White, 06 - Black; xx = Length
2. Roller tube (item 1) is complete with end bushings, LED strip
3. Arm Assemblies (items 11, 12) includes items 4, 13, 14, 15. Does not include
attaching pins. For attach pins order item 17 (1 kit per arm).
4. Original and current mounting brackets are not interchangeable. Replacement
brackets must match the existing brackets. Original brackets can be identified
by the 3 hole pattern beside the knuckle.
5. The roller tube e-clips w/ tab replace the previous round e-clips and washers
used on the idler side.
For LED replacement parts and service procedures refer to 052584-301 “LED Service Manual for
Vertical Arms” available on-line at www.carefreeofcolorado.com
Replaces Washers,
and Round E-Clip
FL030