Carefree Universal Eclipse User manual

052568-001r5 Printed in USA August, 2017
I NSTALLATION M ANUAL
ECLIPSE ARMS AND CANOPY
THIS PUBLICATION COVERS MODELS:
RV Universal Eclipse w/ Single Switch or Direct Response Electronics
Read this manual before installing or using this product. Failure to follow the instructions
and safety precautions in this manual can result in personal injury and/or cause the
product to not operate properly.
LED Lighting
These instructions apply to OEM and Aftermarket Installations. Details and procedures
unique to a specific application are labeled appropriately.
Adjustable Pitch
E0069
Flat
Steep

TABLE OF CONTENTS
Product Overview.......................................................................................................................... 1
Eclipse Patio Awning Specifications:..............................................................................................1
Eclipse Patio Awning Options: .......................................................................................................1
Component Checklist..............................................................................................................................2
Installation ..................................................................................................................................... 4
Required Pre-Installation Preparation.....................................................................................................4
Installing an Awning Rail.........................................................................................................................4
Assembling the Awning ..........................................................................................................................5
Mounting the Awning..............................................................................................................................6
Electrical ........................................................................................................................................ 8
Single Switch Installation........................................................................................................................8
Direct Response Installation.................................................................................................................10
Routing the Wire into the Vehicle.................................................................................................10
Installing the Switches..................................................................................................................10
Wiring an Additional Patio Switch.................................................................................................11
Installing the Control Box .............................................................................................................11
Installing the Remote Receiver.....................................................................................................12
Programming the Receiver...........................................................................................................12
Wiring Diagram - Direct Response...............................................................................................13
Ignition Lockout Sensor Installation (Optional).............................................................................14
Final Assembly ............................................................................................................................ 15
Attaching the Fascia and Bottom Cover...............................................................................................15
Securing the Fabric...............................................................................................................................15
Removing the Temporary Assembly Pins.............................................................................................16
Installing the Tractioners.......................................................................................................................16
Optional LED’s............................................................................................................................. 17
Wire Routing.........................................................................................................................................17
Switch Installation.................................................................................................................................18
Power Connection for optional OEM RGB LED's.................................................................................19

052568-001r5 Printed in USA August, 2017
P ROPRIETARY S TATEMENT
The Eclipse Patio Awning is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The
information contained in or disclosed in this document is considered proprietary to Carefree of Colorado.
Every effort has been made to ensure that the information presented in the document is accurate and
complete. However, Carefree of Colorado assumes no liability for errors or for any damages that result
from the use of this document.
The information contained in this manual pertains to the current configuration of the models listed on the
title page. Earlier model configurations may differ from the information given. Carefree of Colorado
reserves the right to cancel, change, alter or add any parts and assemblies, described in this manual,
without prior notice.
Carefree of Colorado agrees to allow the reproduction of this document for use with Carefree of Colorado
products only. Any other reproduction or translation of this document in whole or part is strictly prohibited
without prior written approval from Carefree of Colorado.
S AFETY I NFORMATION
This is the safety alert symbol. It is used to alert individuals to potential
personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible personal injury or death.
WARNING
Indicates a hazardous situation, which if not avoided, could result in death or
serious bodily injury.
CAUTION
Indicates a hazardous situation, which if not avoided, may result in minor or
moderate bodily injury.
NOTICE
Indicates a situation that may result in equipment-related damage.
General Safety:
WARNING Shock Hazard. Always disconnect battery or power source before
working on or around the electrical system.
WARNING Always wear appropriate safety equipment (i.e. goggles).
CAUTION Always use appropriate lifting devices and/or helpers when lifting or
holding heavy objects.
NOTICE When using fasteners, do not over tighten. Soft materials such as fiberglass and
aluminum can be "stripped out" and lose the ability to grip and hold.
CALIFORNIA PROPOSITION 65
WARNING This product contains chemicals known to the state of California to cause
cancer or birth defects or other reproductive harm. California’s Proposition 65 requires this
warning to be given to customers in the state of California.
Reference Publications located @ www.carefreeofcolorado.com:'
052568-001 Eclipse Arms and Canopy Installation Manual
052568-201 Eclipse Owner's Manual
052547-301 Eclipse Service Manual
Carefree of Colorado 2145 W. 6
th
Avenue Broomfield, CO 80020 a Scott Fetzer company

Carefree of Colorado Installation Manual ECLIPSE
052568-001r5 1
PRODUCT OVERVIEW
The unique "scissor" style arms eliminate the need for vertical ground supports.
Easy to use 6 position pitch adjustment. The pitch can be left in any position and the Eclipse will roll up
completely! When the awning is rolled back out, it rolls out to the pitch setting previously set.
Worm gear style motor is billow proof - eliminates the need for travel locks.
In the minimum (flat) pitch, the auto-dump feature automatically releases to allow water to run-off to
prevent water pooling. When the water is gone, the arms return to the fully extended position.
Can be installed using a single switch control or with the Direct ResponseTM electronic system. An RF
remote is available with the Direct ResponseTM system.
Eclipse Patio Awning Specifications:
LENGTH 12' - 21' [366 - 640cm]
EXTENSION: 7' 6 3/4" [230.5cm] Drop @ Min. Pitch: 12" [30.5cm] Drop @ Max. Pitch: 40" [102cm]
Values are approximate, actual dimensions may vary with specific installations.
EXTENSION TIME: 28 Seconds (approx) RETRACTION TIME: 32 Seconds (approx)
POWER REQUIREMENTS: 12VDC (operating range 10VDC to 14VDC) Circuit Rating: 15 amp
POWER SOURCE: Motor and controls are routed and hardwired into the vehicle’s 12V system
EMERGENCY RETRACT: Electrical override system (external power source)
COLOR: Hardware: White, Black or Satin
Fabric: Heavy Duty Vinyl or Acrylic Fabric with Alumaguard or Uniguard
(refer to sales literature for colors)
Fabric Wrap: Weatherguard or Metal Wraps: Alumaguard or Uniguard
Eclipse Patio Awning Options:
Alumaguard Awning Wrap 2

12V Direct Response Auto-Retract System
Uniguard Awning Wrap 2

Remote Control
3
SunBlocker
NOTES:
1. Installation with optional SunBlocker shade requires a minimum power source of 12VDC
(operating range 12VDC to 14VDC)
2. Selected at time of initial order.
3. Remote Control available with Direct Response installations only

ECLIPSE Installation Manual Carefree of Colorado
2 052568-001r5
COMPONENT CHECKLIST
Optional equipment and electronics are shown but may not be included with a particular arm set. Refer to
the original purchase order to determine which options are applicable.
The Rail Extension Kit is standard for aftermarket installations.
For Aftermarket Direct Response, refer to Eclipse upgrade kit SR0036.
Remote Control and Ignition Lock-Out are only available when Direct Response is installed.
21 3
13
10
1918
E0012c
9
8
7
6
5
7
4
Single Switch (Standard)
Direct Response (Optional)
21 22
Remote Control Kit (Optional)
25 26 27
30
31
Ignition Lock-Out Kit (Optional)
29
20
Roller Tube
Arms
24
23
28
8
11
Common Hardware
Rail Extension (aftermarket)
171615
12
Carefree of Colorado
12V DIRECT RESPONSE
CONTROL BOX
PARTNO. 060574-003
MOTION SENSITIVITY
SWITCH
RR433
(Optional)
PATIO S WITCH
MOTION SENSOR
MODE SWITCH
A B
MOTOR
+12V
GROUND
FUSE (15A)
TO EYE PORT on RP24 Program Mode
Press to Learn Transmitter
UP
RR
Version_______

Carefree of Colorado Installation Manual ECLIPSE
052568-001r5 3
ITEM DESCRIPTION QTY NOTE
1 Rollbar Assembly 1
2 Screw, HWHC #6 x 3/8 2
3 Tractioner 2 2
4 Screw, Truss Head, SQ Drive #10 x 5/8 2 2
5 LH Arm Assy, Idler 1
6 RH Arm Assy, Motorized 1
7 Fascia Assy 2
8 Bottom Cover 2
9 Screw, Lag 1/4 x 1 1/2 8
10 Screw, Truss Head, SQ Drive #10 x 5/8 4
11 Screw, SHC, Self-Tapping #8 x 3/4 4
12 Screw, HWHC #6 x 3/8 2
13 Jumper Cable 1 5
15 Rail Extension Kit 1 3,4
16 Screw, SHC #10 x 1/2 4 3,4
17 Nylock Nut 10-32 4 3,4
18 Screw, Lag 1/4 x 2 1/2 8 3
19 Rivet, Moly 7/32 4 3
20 Switch Kit, Single Switch 1 6
21 Control Box, Direct Response 1
22 Screw, Phillips Truss Head #6 x 1/2 2
23 Harness, Power, Motor 2
24 Switch Kit, Direct Response (includes bezel and connector harnesses) 1
25 Receiver, RF, 433 MHz 1
26 Screw, Phillips Truss Head #6 x 1/2 2
27 Cable 60” 1
28 Remote Control Key FOB, 433MHz 1
29 Cable 60” 2
30 Sensor, Ignition Lock-Out 1
31 Splitter 1
Notes: 1. Awning configuration is specified at time of order, including awning length, fabric, color and
electronics. Check awning assembly against original purchase order.
2. Screws and Tractioners are furnished with roller tube assemblies equipped with optional
Alumaguard/Uniguard.
3. Used with aftermarket installations.
4. Rail Extension kit includes hardware for two arms (items 15, 16,17). Standard for
aftermarket installations.
5. Place Jumper Cable (item 14) with RV owner information. Installation manual, if included,
is for installer reference.
6. OEM's may choose to furnish the control switch (item 20). The switch must be a DC
polarity reversing switch with dynamic brake.

ECLIPSE Installation Manual Carefree of Colorado
4 052568-001r5
INSTALLATION
REQUIRED PRE-INSTALLATION PREPARATION
1. Park the vehicle on a flat surface and level the unit.
2. If this is an upgrade for a manual patio awning, follow the awning manufacturer's instructions and
remove the awning from the coach including the roll bar and canopy.
2.1. Remove all brackets.
2.2. Plug and seal all mounting holes. The new Eclipse arms may not match the locations of the old
awning arms.
2.3. Remove the roll bar from the arms and on a flat clean surface, roll the fabric onto the roll bar.
2.4. If the canopy is equipped with Alumaguard, remove the tractioners and set aside. These will be
reinstalled after the new awning assembly is installed.
3. Check where the awning arms will be installed. The arms fit snug to the side of the vehicle and must not
cover or interfere with exhaust vents, lights etc.
4. If there is an awning rail installed, check that the awning rail runs the full length of the awning. Please
refer to the note under "Installing an Awning Rail" before proceeding.
5. Refer to the important note on page 6 about the required positioning of the centerline of the roll bar.
INSTALLING AN AWNING RAIL
NOTE: For canopies WITHOUT Alumaguard or Uniguard: If the vehicle already has a full-length awning
rail installed, skip to step 6.
For Alumaguard and Uniguard installations: If the existing awning rail is incorporated into the
coach trim or a drip rail, it will be necessary to mount a standard awning rail flat on the coach wall.
The awning rail and arms must be positioned so that any existing trim does not interfere with the
Alumaguard or Uniguard's "Flex Connect" or the awning arm when in the closed position.
1. Determine the optimum positioning of the awning so that the arms will not interfere with the door frame or
light fixtures. The centerline of the rail should be above the door opening a minimum of 6" for vinyl and 7" for
Alumaguard/Uniguard. After determining mounting position, mark the position with a chalk line.
2. Awning rail must be level.
3. Seal the back of the rail with silicone sealant or putty tape.
4. Align the awning rail onto the wall and secure with #10 x 3/4” screws. Use all the attach holes in the
rail.
NOTICE Make sure the screws are securely mounted to the structural frame of the vehicle.
5. Use a screwdriver to spread open one end of the awning rail on
the installation side.
6. File any sharp edges or burrs from the end of the rail. This will
help protect the awning fabric from damage during installation.
7. Spray inside the awning rail track with silicone lubricant.
Standard Awning Rail
Mounted to Coach Wall
Flex Connect Must Be
Flat When the Awning
is Closed
UNIGUARD
E0050
Standard Awning Rail
Mounted to Coach Wall
ALUMAGUARD
Coach WallCoach Wall
Spread open the
end of the awning rail T0012

Carefree of Colorado Installation Manual ECLIPSE
052568-001r5 5
ASSEMBLING THE AWNING
1. Decide on the location of the switches and control box to determine the cable routing.
2. If the motor and Direct Response sensor cables are to be routed through the RV wall at the bottom of
the arm, no modification is required. Go to step 3.
2.1. If the motor and Direct Response sensor cables are to be routed through the RV wall at the top of the
arm:
2.2. Remove the plastic wrap at the top of the motorized arm. Partially open the arm being careful to
not let the arm extend more than 6”.
NOTE: The arm is under tension from the gas shock located in the arm.
2.3. Pull the cable(s) out of the slot(s) in the rear of the back channel and pull the cables out of the hole
in the top of the channel.
2.4. Secure the top of the arm in the closed position using a plastic wrap or equivalent.
3. For Aftermarket Installations: An extension
kit is furnished for aftermarket installations.
3.1. At the top of the arms, remove the rail
caps.
3.2. Attach the rail extension to the rail as
shown.
NOTICE During assembly and
installation, The arm assemblies must
remain perpendicular to the roller
assembly. Failure to handle the arms
carefully can bend the drive shaft.
4. Align the roller assembly with the end cap on
the motorized arm assembly. Rotate the end
cap until the slot in the cap aligns with the
empty slot in the roller assembly, and then
press the roller assembly fully into the cap.
The end cap must seat squarely over the
end of the roller assembly when complete.
NOTE: The roller assembly must be oriented with the fabric going over the roller toward the mounting surface.
5. Secure the end cap to the roller tube assembly using two #10 square-drive screws.
6. Repeat steps 4 and 5 to attach the non-motorized arm assembly to the roller tube assembly.
Remove Rail Cap
and Screws
Rail Extension Assy
#10-32 SHCS
and Nylock Nut
(2 per arm)
E0068
Roller Tube
Assembly
Align Slots
End Cap
#10 x 5/8 Screw (qty: 4)
End Cap
E0020a

E CLIPSE Installation Manual Carefree of Colorado
6 052568-001r5
M OUNTING THE A WNING
CAUTION It is recommended that at least three people install the awning due to its
size and weight.
NOTE: For the bottom 3 mounting holes: if mounting into structure, use the 1/4 x 1 1/2 screws; if not
attaching into structure, use the moly rivets.
The upper mounting holes must attach into structure using the screws provided. If structural backing is not
available for the upper mounting holes, it will be necessary to use the aftermarket rail extension so that the
upper brackets can mount into the structural members at the roof line.
1. Check the location where the awning is to be mounted. Ensure that the awning will not interfere with
other equipment on the vehicle, such as a slide out room, light fixtures, exhaust vents etc.
2. On the awning rail, mark the location of the centerline of the arm assemblies.
3. From those marks, measure down vertically a distance of 55" ± 1/4" from the centerline of the awning
rail. These will be the initial mounting holes.
4. Unroll the canopy one wrap.
5. With one person holding each arm, the third person should thread the polyrod (the plastic rod on the
edge of the fabric) into the awning rail, starting at one end. Carefully move across the vehicle, gently
pulling the fabric into the rail, until the awning is in the pre-determined location.
NOTE: While the awning fabric is fairly robust, care must be taken not to snag it on the awning rail.
6. For installations without the rail extension: Align the first mounting hole in the motorized arm with the
location marked in step 2. The arm assembly must be perpendicular to the awning rail.
7. For installations with the rail extension: Butt the top of the rear channel against the awning rail as
shown in Detail A.
IMPORTANT NOTE: For Uniguard and Alumaguard installations, the centerline of the roll bar
must be 3/4" ± 1/4" above the centerline of the awning rail.
8. Drill a 5/32” hole at the first mounting hole for the RH (motorized) arm
8.1. If the hole goes into a structural member, attach the motorized arm using a 1/4 x 1 1/2” lag screw.
8.2. If the hole is through the outer skin only, ream the hole out to 1/4" and attach arm with a moly rivet.
55" ± 1/4”
E0022a
90o
Typ.
Centerline
of Arm
Centerline
of Arm
Awning Length
Fabric Width
5” 5”
Awning
Rail
= Flat Mounting
Surface Area
4 1/4” x 70”
6”-7”
Clearance
from top of
door
6”
Drill Area for
Upper Cable
Routing
7 1/2”
68 1/4”
First Mounting
Hole (ref)
Drill Area for
Lower Cable
Routing
Align Top of Rail
with Bottom of
Awning Rail
Detail A
Aftermarket Arm
Alignment