Carimali ARMONIA TOUCH User manual

QUICK START GUIDE
ARMONIA TOUCH
NT-05088-02-EN

MACHINE DESCRIPTION
LEGEND
1 . PRODUCT CANISTER
2 . COFFEE HOPPER
3 . PRODUCT CANISTER / COFFEE HOPPER
4 . CARD READER
5 . DECAFFEINATED DOOR
6 . DOSE BUTTON
7 . PEOPLE PRESENCE SENSOR
8 . DISPLAY
9 . INFO BUTTON
10 . RUBBER PROTECTION
11 . SHIFT BUTTON
12 . STEAM WAND
13 . DOOR LOCK
14 . GROUNDS BIN
15 . ADJUSTABLE DELIVERY OUTLETS
16 . DRIP TRAY
Only for US market (ETL Sanitation): The equipment shall be installed with backflow protection to
comply with applicable federal, state and local codes.
2
5
8
1
2
1
3
1
4
6
11
1
0
9
3
7
1
6
1
5
1
4

STARTING UP
Power ON the machine by means of the main switch inside the machine and then close the front door. (pic. A)
After checking that the machine door is closed and the ground bin and the drip tray are inserted, press the key No.8
(ON/OFF) to turn ON the machine ( PIC. A ).
(FOR SELF CONFIGURATION , press the key n°8 (on/off ) and then insert the waiter password 61111).
When the boiler temperature of 50°C (122°F) is reached, the machine carries out a group rinsing. The display shows:
When the set-up temperature is reached, the keypad lights are on and the display shows:
For machine configuration Standard or Self:
SELECT DRINK
G.AUTO CLEANING
Pic. A
ON
OFF
A) Power on the machine by means the main switch
Inside the machine .
Pic. A

To switch OFF the machine press key n°11- Info (Pic.A) and then press key n° 8-Off (Pic.B).
FILL IN BEAN HOPPER AND CANISTER
Fill in the required amount for daily consumption in order to keep coffee and product always fresh.
Pic. A Pic. B
SELECT DRINK
2xEspresso Americano
Cappuccino Latte Macchiato
Choco Mocha
Espresso Caffè latte
Coffee temperature
XXX °C
Steam temperature
YYY °C

DISPLAY THE AVAILABL
E
Press the SHIFT key with the
machine in SELECT DRINK
Press the INFO key
with the machine in SELECT DRINK mode to
Where XXX indicates the coffee boiler temperature and YYY indicates
E
SHIFT DRINK SELECTIONS
AND BOILERS TEMPERAT
machine in SELECT DRINK
mode to display the available
shift
with the machine in SELECT DRINK mode to
display the
boilers temperature
Where XXX indicates the coffee boiler temperature and YYY indicates
the steam boiler temperature.
COFFEE TEMPERATURE
XXX
STEAM TEMPERATURE
YYY
SELECT DRINK
2xEspresso Americano
Cappuccino Latte Macchiato
Choco Mocha
Espresso Caffè latte
AND BOILERS TEMPERAT
URE
shift
drink selections :
boilers temperature
:

1) COFFEE/CAPPUCCINO/CHOCO DISPENSING
Adjust the coffee
dispenser to the correct height and place a cup under it then press the desired dose key.
For Shift doses, press Shift
key first and then the desired dose key.
For Waiters’ Card place the smart card above the proper reader before pressing the dose key.
The display shows:
Where “XXXXXXXX” indicates the selected dose key name.
The cursor indicates the amount of drink being dispensed.
PLEASE NOTE:
Pressing the same dose key during dispensing can stop the selected dose (not available for Self configu
2) HOT WATER DISPENSING
Place a cup under the hot water outlet, and press the hot water
programmed dose is over. The display shows:
PLEASE NOTE:
•Pressing t
he same dose key during dispensing may stop the selected dose
•
Hot water cannot be dispensed simultaneously with steam.
3) DECAFFEINATED DISPENSING (not available for Self configuration)
Adjust the coffee dispenser
to the correct height and place a cup under it , then open the decaffeinated coffee door, the display shows :
- Pour in the powdered coffee
- Close the decaffeinated door
-
Press the desired dose key. The display shows:
The selected dose wi
ll be dispensed without the activation of the grinders.
PLEASE NOTE:
•
Pressing the same dose key during dispensing may stop the selected dose (not available for Self configuration).
•
If the decaffeinated door is not closed, or if the dose button is not selec
20 seconds. The coffee group will carry out a cleaning cycle of the brewing chamber.
4) EXTRAMILK DISPENSING (only LM machine, not available for Self configuration)
Press any milk-based key
and keep it pressed, after 2 seconds foamed
By releasing the pressed key, dispensing will be stopped.
DISPENSING
1) COFFEE/CAPPUCCINO/CHOCO DISPENSING
dispenser to the correct height and place a cup under it then press the desired dose key.
key first and then the desired dose key.
For Waiters’ Card place the smart card above the proper reader before pressing the dose key.
Where “XXXXXXXX” indicates the selected dose key name.
The cursor indicates the amount of drink being dispensed.
Pressing the same dose key during dispensing can stop the selected dose (not available for Self configu
ration).
Place a cup under the hot water outlet, and press the hot water
dose key . .
Dispensing will be automatically stopped once the
programmed dose is over. The display shows:
he same dose key during dispensing may stop the selected dose
(not available for Self configuration).
Hot water cannot be dispensed simultaneously with steam.
3) DECAFFEINATED DISPENSING (not available for Self configuration)
to the correct height and place a cup under it , then open the decaffeinated coffee door, the display shows :
Press the desired dose key. The display shows:
ll be dispensed without the activation of the grinders.
Pressing the same dose key during dispensing may stop the selected dose (not available for Self configuration).
If the decaffeinated door is not closed, or if the dose button is not selec
ted, the machine will automatically cancel this function after
20 seconds. The coffee group will carry out a cleaning cycle of the brewing chamber.
4) EXTRAMILK DISPENSING (only LM machine, not available for Self configuration)
and keep it pressed, after 2 seconds foamed
or steamed
milk will start being dispensed, the display shows:
By releasing the pressed key, dispensing will be stopped.
XXXXXXX
HOT WATER
SELECT DRINK
Espresso
XXXXXXX
EXTRAMILK
dispenser to the correct height and place a cup under it then press the desired dose key.
ration).
Dispensing will be automatically stopped once the
(not available for Self configuration).
to the correct height and place a cup under it , then open the decaffeinated coffee door, the display shows :
Pressing the same dose key during dispensing may stop the selected dose (not available for Self configuration).
ted, the machine will automatically cancel this function after
milk will start being dispensed, the display shows:

STEAM WAND USE AND CLEANING
STEAM WAND NOT AVAILABLE FOR MACHINE IN SELF CONFIGURATION
WE STRONGLY RECOMMEND TO USE AND CLEAN THE STEAM WAND AS ABOVE SHOWN
6►DO NOT leave the steam wand into
any liquid at any time
5►Clean the steam wand by means of a
cloth
1►Before using the steam wand press
the steam button to purge the nozzle. 2►Use the steam wand to foam or heat any liquid into the jug by handling the
rubber protection.
3►Press the steam button to stop the
delivery before removing the jug.
4►After using the steam wand press
the steam button to purge the nozzle

AUTOMATIC CLEANING O
AT THE END OF EACH WORKING DAY , AND/
RECOMMEND TO CARRY OUT AUTOMATIC CLEANING OF THE COFFEE GROUP ,THE MIXER AND THE MILK FROTHER
1
►
Keep Shift key pressed for five
seconds.
( for SELF configuration insert the waiter
password 61111).
4
►
Press Start key to confirm.
7
►
Press Start key to confirm the group
cleaning cycle
POWER CLEANER
Remove the silicone tube from the
milk box and place it into the
black support press start for
cleaning
Start
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
AUTOMATIC CLEANING O
F COFFEE GROUP-
MIXER AND MILK FROTH
AT THE END OF EACH WORKING DAY , AND/
OR IN CASE THE MACHINE WILL NOT BE USED SOME TIME, WE STRONGLY
RECOMMEND TO CARRY OUT AUTOMATIC CLEANING OF THE COFFEE GROUP ,THE MIXER AND THE MILK FROTHER
2
►
Press Start key to perform the group
cleaning cycle. Press Skip key to skipping
the Power Cleaner and carry out the next
cleaning
Press Start for cleaning
Press Skip for next cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
3►P
ress
Insert the black pipe support into
the hole in the drip tray grid press
start f
or cleaning
Start
5
►
Wait the end of the Power Cleaner.
Afterwards the machine exits the cleaning
menu and it will be ready to dispense
drinks.
8►Open the machine door
9
►
Clean the group from any coffee
residues. Then clean the group filters by
means of a cloth
GROUP CLEANING
CLEAN AND CLOSE FRONT
POWER CLEANER
PLEASE WAIT
50
Start
Skip
GROUP CLEANING
OPEN FRONT PANEL AND
CLEAN COMPONENT
6
►
Keep
seconds.
( for SELF configuration insert the waiter
password 61111).
MIXER AND MILK FROTH
ER
OR IN CASE THE MACHINE WILL NOT BE USED SOME TIME, WE STRONGLY
RECOMMEND TO CARRY OUT AUTOMATIC CLEANING OF THE COFFEE GROUP ,THE MIXER AND THE MILK FROTHER
.
ress
Start key to confirm.
POWER CLEANER
Insert the black pipe support into
the hole in the drip tray grid press
or cleaning
Start
Clean the group from any coffee
residues. Then clean the group filters by
means of a cloth
GROUP CLEANING
CLEAN AND CLOSE FRONT
Keep
Shift key pressed for five
seconds.
( for SELF configuration insert the waiter
password 61111).

10
►
Close the machine door
GROUP CLEANING
CLEAN AND CLOSE FRONT
16
►
Press Start key to confirm
Prepare a solution of water and detergent
(q.ty 200ml for standard version, 500ml if
milk pump present) by following the
instructions indicated in the product label.
Take the milk feeding tube out of the milk
box. Insert the milk feeding tube into a
container with detergent.
1
3
►
Press Start key to confirm the mixer
cleaning cycle (only for machine with
choco unit)
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
MILKER CLEANING
Insert cleaning solution
Start
17
►
Wait the end of the milker cleaning
cycle.
18
►
A
t the end of the milker cleaning
cycle the display will show
Put the milk infeed pipe into a glass of cold
water.
Press S
tart
cycle.
MILKER CLEANING
PLEASE WAIT
1.59
MILKER CLEANING
Repeat using only water, press
Start
11
►
Open the front door and insert the
detergent tablet into the brewing chamber.
Close the machine door.
12
►
. Wait the end of the group cleaning
cycle.
1
4
►
Wait the end of the mixer cleaning
cycle.
15
►
Press
cleaning cycle
frother).
GROUP CLEANING
INSERT CLEANSER
GROUP CLEA
MIXER CLEANING
PLEASE WAIT
2.02
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
t the end of the milker cleaning
cycle the display will show
.
Put the milk infeed pipe into a glass of cold
tart
key to confirm Miker rinsing
MILKER CLEANING
Repeat using only water, press
start for cleaning
Start
. Wait the end of the group cleaning
Press
Start key to confirm the milker
cleaning cycle
(only for machine with milk
GROUP CLEA
NING
PLEASE WAIT
4.42
Press Start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING

IN CASE THE COFFEE MACHINE IS EQUIPPED WITH STEAM BOILER BUT WITHOUT MILK FROTHER IS NECESSARY TO
PERFORM THE STEAM BOILER CLEANING.
Please note : the
boiler cleaning is displayed only if the “Steam boiler cleaning frequency” parameter has been programmed.
15►Press Start key to confirm the milker
cleaning cycle
18►
AT THE END OF THE CLEANING CYCLES PROCEDURESTHE DISPLAY WILL SHOW :
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
BOILER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
18
►
During this time out you can clean the
touch screen using a soft cloth and water.
DISPLAY CLEANING
PLEASE WAIT
0.15
IN CASE THE COFFEE MACHINE IS EQUIPPED WITH STEAM BOILER BUT WITHOUT MILK FROTHER IS NECESSARY TO
PERFORM THE STEAM BOILER CLEANING.
boiler cleaning is displayed only if the “Steam boiler cleaning frequency” parameter has been programmed.
AT THE END OF THE CLEANING CYCLES PROCEDURESTHE DISPLAY WILL SHOW :
1
6
►
Wait the end of the steam boiler
partial draining (BOILER CLEANING).
Hot water will be drained into the drip tray.
17
►
A
cleaning
the display
Start
BOILER CLEANING
PLEASE WAIT
0.20
19
►
At the end of the Display cleaning the
display shows.
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
MILKER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
20
►
At this stage you can use the display
to see how to manually clean the coffee
dispenser, the milk frother, the mixer, the
hopper, the grounds bin and the drip tray
SUGGESTED CLEANING
Manual cleaning of mixer
Other recommended cleaning
Manual cleaning: Milk frother, coffee
Ʌ
SELECT DRINK
GROUNDS BIN FULL
IN CASE THE COFFEE MACHINE IS EQUIPPED WITH STEAM BOILER BUT WITHOUT MILK FROTHER IS NECESSARY TO
boiler cleaning is displayed only if the “Steam boiler cleaning frequency” parameter has been programmed.
AT THE END OF THE CLEANING CYCLES PROCEDURESTHE DISPLAY WILL SHOW :
A
t the end of the steam boiler
cleaning
cycle , press Start key to confirm
the display
cleaning
Press start for cleaning
POWER CLEANING
GROUP CLEANING
MIXER CLEANING
BOILER CLEANING
DISPLAY CLEANING
SUGGESTED CLEANING
Start
At this stage you can use the display
to see how to manually clean the coffee
dispenser, the milk frother, the mixer, the
hopper, the grounds bin and the drip tray
.
SUGGESTED CLEANING
Manual cleaning of mixer
Other recommended cleaning
Manual cleaning: Milk frother, coffee
esc
V

24►
WAIT AT LEAST 10 SECONDS , THE DISPLAY WILL SHOW :
PLEASE NOTE:
a) Do not interrupt the cleaning cycle. If the cleaning cycle is interrupted by any type of operation unrelated to the proced
machine functioning is set back again,
the cleaning cycle will automatically be activated.
b) Only in case that after the automatic cleaning process of the coffee outlet or the milk frother are not properly dispensin
manual cleaning; see the following steps.
FOR CLEANING OPER
ATIONS , CARIMALI STRONGLY RECOMMEND TO USE THE FOLLOWING DETERGENT PRODUCTS:
CLEANING TABLETS
2
2
21
►
Lift the coffee outlets completely.
2
5
►
Clean the grounds bin
compartment.
WAIT AT LEAST 10 SECONDS , THE DISPLAY WILL SHOW :
a) Do not interrupt the cleaning cycle. If the cleaning cycle is interrupted by any type of operation unrelated to the proced
the cleaning cycle will automatically be activated.
b) Only in case that after the automatic cleaning process of the coffee outlet or the milk frother are not properly dispensin
ATIONS , CARIMALI STRONGLY RECOMMEND TO USE THE FOLLOWING DETERGENT PRODUCTS:
MILK FROTHER CLEANER
2
►
Remove and empty the grounds bin.
2
3
►
R
emove and empty also the drip
tray.
( only for machines without direct
water discharge )
2
6
►
Reinsert the drip tray.
2
7
►
Reinsert the grounds bin .
SELECT DRINK
GROUNDS BIN
OPEN
a) Do not interrupt the cleaning cycle. If the cleaning cycle is interrupted by any type of operation unrelated to the proced
ure, when the
b) Only in case that after the automatic cleaning process of the coffee outlet or the milk frother are not properly dispensin
g, carry out a
ATIONS , CARIMALI STRONGLY RECOMMEND TO USE THE FOLLOWING DETERGENT PRODUCTS:
MILK FROTHER CLEANER
emove and empty also the drip
( only for machines without direct
water discharge )
Reinsert the grounds bin .

MANUAL CLEANING: MILK FROTHER, COFFEE OUTLET
1 ►Open the machine remove the coffee
outlet from its holder .
2 ►Remove the milk frother from the
coffee outlet and disconnect Silicone
tubes No. -3- and -4.
3 ►Disassemble the milk frother in all its
parts (first by turning and then by pulling as
shown in the picture) and wash it either by
hand or in a dishwasher. Make sure that all
the holes are free from milk residues and
also to use provided tools to clean the
holes. Check also that the O-rings are in
good condition
4 ►Disassemble the coffee outlet (1)
and wash it by hand or in a dishwasher.
Make sure that all the holes are free
from any coffee residues , and also to
use provided tools to clean the holes.

MANUAL CLEANING OF MIXER
WE STRONGLY RECOMMEND CLEANING THE MIXERS ONCE A DAY
1►Open the machine door 2►Remove the pipe from the mixer
3
►Remove the product outlet elbow
1, then turn the flange 2 anticlockwise,
then remove the mixer 3
4
►
Remove the Decanter
5
►
Rinse the Mixer and the Decanter
in a sink
7
►
Insert the mixer 1 then turn the
flange clockwise 2 , then reinsert the
product outlet elbow 3.
8►Reinsert the pipe from the mixer
6
►
Reinsert the Decanter
2
1
3
3
2
1

OTHER RECOMMENDED CLEANING
DRIP TRAY CLEANING GROUNDS BIN CLEANING
HOPPER CLEANING DISPENSER CLEANING
a) Once a week clean the dispenser
by means of a cloth and approved
food detergent
b) Open the front door and remove
the product outlet .
c) Remove the canister
a) Once a week clean the hopper by
means of a cloth and approved food
detergent.
b) Turn the screw on the top of the
machine anticlockwise and then
remove the hopper.
Once a day rinse the grounds bin in a
sink.
Once a day rinse the drip tray in a sink.

CHUTES CLEANING
GRINDERS ADJUSTMENT
Please Note: Brew and throw two doses, the third one will be dispensed with the new grinder set
a) Open the decaffeinated door and
remove the chute .
c) Once a week clean the coffee chute by
means of a brush and approved food
detergent
b) Once a week clean the
decaffeinated chute by means of a
brush and approved food detergent
a) Turn the screw on the top of
the machine anticlockwise and
then remove the hopper.
b) Move the adjustment to the
right to get coarse coffee powder,
to the left for finer.
c) Reinsert the hopper and lock it
by turning the screw clockwise.

MILK FROTHER ADJUSTMENT
Foam setting
The milk frother is equipped with a FOAM REGULATOR which sets the quantity of air needed to froth milk.
Open the machine door turn the ring nut clockwise for thicker foam (small bubbles), or turn it anticlockwise for more voluminous foam
(large bubbles) then lock it with the locknut. Pic.A.
Milk temperature setting
The milk frother is equipped with a MILK TEMPERATURE REGULATOR which reduces the quantity of sucked milk.
Turn the regulator clockwise to increase the milk temperature, or turn it anticlockwise to reduce it.
Pic. A

a) Lift the coffee outlets completely
MACHINE FUNCTIONS ME
1) Alarm for machine door position
Cause: the front door is open; the
micro switch do
Result: shutdown of the machine functions
Solution: press ( Info ) key,
the display shows
Close the door and turn the machine ON.
2) Full grounds bin alarm
Cause: g
rounds bin full; the number of coffee grounds in the bin has reached the programmed value
Result: shutdown of the coffee-
based dispensing selections
Solution: p
ress ( Info ) key, the display shows :
GROUNDS BIN FULL GROUNDS BIN
FULL
After 10 seconds the display shows :
a) Lift the coffee outlets completely
MACHINE FUNCTIONS ME
SSAGES
micro switch do
es not touch the door
the display shows
:
rounds bin full; the number of coffee grounds in the bin has reached the programmed value
based dispensing selections
ress ( Info ) key, the display shows :
FULL
b) R
emove and empty the grounds bin.
OFF
CLOSE FRONT PANEL
SELECT DRINK
EMPTY GROUNDS BIN
WAIT 10 SEC.
CLOSE THE GROUNDS BIN
OPEN DOOR
OPEN DOOR
GROUNDS BIN FULL
GROUNDS BIN FULL
GROUNDS BIN OPEN
emove and empty the grounds bin.

Press ( Info ) key, the display shows:
Reinsert the grounds bin into its housing.
3) Message of missing coffee
Cause: there is no coffee into the hopper and therefore into the brewing chamber
Result: the machine interrupts the coffee-based dispensing selections
Solution : press ( Info ) key, the display shows :
to reset the alarm put coffee into the hopper and press again the dose required.
4) Message of missing decaffeinated
Cause: Missing coffee in the decaffeinated door and in the brewing chamber
Result: The machine interrupts the decaffeinated dispensing selections
Solution : press ( Info ) key, the display shows :
To reset the alarm put decaffeinated into the decaf door and press again the dose required.
SELECT DRINK
FILL THE HOPPER
SELECT DRINK
INSERT DECA COFFEE
POWNDER 7/8 gr. min.
CLOSE THE GROUNDS BIN
GROUNDS BIN OPEN
MISSING COFFEE
MISSING COFFEE
MISSING DECAF.
MISSING DECAF.

5) Message of drip tray not in position.
The display will show the following message:
Cause: the drip tray is not in position. The micro switch contact is open.
Result: The message is displayed without disabled the dispensing keys.
Solution : press ( Info ) key, the display shows :
reinsert the drip tray.
6) Message of drip tray full. ( ONLY FOR MACHINES WITHOUT DIRECT WATER DISCHARGE )
The display will show the following message:
Cause: waste bin is full. The quantity of water inside the drip tray touches the level probe .
Result: shutdown of the dispensing keys.
Solution : press ( Info ) key, the display shows :
remove the drip tray and empty it.
PLEASE NOTE: FOR ALL OTHER MESSAGES PLEASE REFER TO YOUR SERVICE CENTER.
SELECT DRINK
DRIP TRAY OUT
INSERT DRIP TRAY
DRIP TRAY OUT
SELECT DRINK
EMPTY THE DRIP TRAY
DRIP TRAY FULL
DRIP TRAY FULL

B) ACCESS THE MAIN SETTING MENUS
WITH SMART CARD
To enter the programming environments, place one of the following smart cards above the proper reader with the led light ON w
machine in OFF mode:
-WAITER SMART CARD
-OWNER SMART CARD
if the inserted card it is c
orrect the reader led light off .
Keep “SHIFT” key pressed for 5 seconds
, the display shows the main menu programming environments as above described.
Carimali S.p.A. con socio unico
Via Industriale, 1
T: [phone] F
: [phone]
www.carimali.com – service@ca
rimali.com
EXIT
DEL
ENTER
-
LED
WITH SMART CARD
To enter the programming environments, place one of the following smart cards above the proper reader with the led light ON w
orrect the reader led light off .
, the display shows the main menu programming environments as above described.
Via Industriale, 1
- 24040 Chignolo d'Isola (BG) - Italia
: [phone]
rimali.com
KEYS
NUMBER
1
Exit (edit )
2
Insert blank
3
Delete character
4
Scroll
5
-
6
+
7
Enter
8
On
9
Steam
10
Hot water
11
Info
12
Shift/Clean
SRC / Del all
INS
+
On-Off / Esc
To enter the programming environments, place one of the following smart cards above the proper reader with the led light ON w
ith the
, the display shows the main menu programming environments as above described.
FUNCTION
PASSWORD
NUMBER
Exit (edit )
1
Insert blank
2
Delete character
3
Scroll
/Delete all 4
5
+
6
Enter
7
On
-Off / Esc
Steam
Hot water
Info
Shift/Clean