CARLO GAVAZZI DPB01 User manual

Specifications are subject to change without notice (09.05.05) 1
Monitoring Relays
Product Description Ordering Key
Housing
Function
Type
Item number
Output
Power supply
• TRMS 3-phase over and under voltage,
phase sequence and phase loss monitoring relays
• Detect when all 3 phases are present and have the
correct phase sequence (except for DPB01...N and
PPB01...N)
• Detect if all the 3-phase-phase or phase-neutral volt-
ages are within the set limits
• Upper and lower limits separately adjustable
• Measure on own power supply
• Selection of measuring range by DIP-switches
• Adjustable voltage on relative scale
• Adjustable delay function (0.1 to 30 s)
• Output: 8 A SPDT relay N.E.
• For mounting on DIN-rail in accordance with
DIN/EN 50 022 (DPB01) or plug-in module (PPB01)
• 22.5 mm Euronorm housing (DPB01)
or 36 mm plug-in module (PPB01)
• LED indication for relay, alarm and power supply ON
Type Selection
Mounting Phase sequence Output Supply: 208 to 240 VAC Supply: 380 to 480 VAC
detection
DIN-rail yes SPDT DPB 01 C M23 DPB 01 C M48
Plug-in yes SPDT PPB 01 C M23 PPB 01 C M48
DIN-rail no SPDT DPB 01 C M23 N DPB 01 C M48 N
Plug-in no SPDT PPB 01 C M23 N PPB 01 C M48 N
Input
L1, L2, L3, N DPB01: Terminals L1, L2, L3, N
PPB01: Terminals 5, 6, 7, 11
Measure on own supply
Note: Connect the neutral only
if it is intrinsically at the star
centre
Measuring ranges
208 to 240 ∆VAC 177 to 275 ∆VAC
380 to 480 ∆VAC (DPB01CM48) 323 to 550 ∆VAC
380 to 415 ∆VAC (PPB01CM48) 323 to 475 ∆VAC
Ranges
Upper level +2 to +22%
of the nominal voltage
Lower level -22 to -2%
of the nominal voltage
Note: The input voltage
must not exceed the maximum
rated voltage or drop below
the minumum rated voltage
reported above.
Hysteresis
Set points from 2 to 4% 1%
Set points from 4 to 22% 2%
True RMS 3-Phase, 3-Phase+N, Multi-function
Types DPB01, PPB01
Input Specifications
Output SPDT relay
Rated insulation voltage 250 VAC
Contact ratings (AgSnO2)µ
Resistive loads AC 1 8 A @ 250 VAC
DC 12 5 A @ 24 VDC
Small inductive loads AC 15 2.5 A @ 250 VAC
DC 13 2.5 A @ 24 VDC
Mechanical life ≥30 x 106operations
Electrical life ≥105operations
(at 8 A, 250 V, cos ϕ= 1)
Operating frequency ≤7200 operations/h
Dielectric strength
Dielectric voltage 2 kVAC (rms)
Rated impulse withstand volt. 4 kV (1.2/50 µs)
Output Specifications
DPB 01 C M23
3-phase or 3-phase+neutral
line voltage monitoring relay
for phase sequence, phase
loss, over and under voltage
(separately adjustable set
points) with built-in time
delay function.
Supply ranges from 208 to
480 VAC covered by two
multivoltage relays.
DPB01 PPB01

2Specifications are subject to change without notice (09.05.05)
DPB01, PPB01
Mode of Operation
Connected to the 3 phases
(and neutral) DPB01 and
PPB01 operate when all 3
phases are present at the
same time, the phase
sequence is correct (not
DPB01...N and PPB...N) and
the phase-phase (or phase-
neutral) voltage levels are
within set limits.
If one or more phase-phase
or phase-neutral voltages
exceeds the upper set level
or drops below the lower set
level, the red LED starts
flashing 2 Hz and the output
relay releases after the set
time period. In any case if
phase-neutral measurement
is selected both phase-
phase and phase-neutral
voltages are monitored. If the
phase sequence is wrong or
one phase is lost, the output
relay releases immediately.
Only 200 ms delay occurs.
The failure is indicated by the
red LED flashing 5 Hz during
the alarm condition.
Example 1
(mains network monitoring)
The relay monitors over and
under voltage, phase loss
and correct phase sequence.
In case of DPB01...N or
PPB01...N, the relay moni-
tors over and under voltage.
Example 2
(load monitoring)
The relay releases in case of
interruption of one or more
phases, when one or more
voltages drop below the low-
er set level or exceed the
upper set level.
Power supply Overvoltage cat. III
Rated operational voltage (IEC 60664, IEC 60038)
through terminals:
L1, L2, L3, N (DPB01)
5, 6, 7, 11 (PPB01)
M23 - Delta Voltage: 208 to 240 VAC ± 15%
45 to 65 Hz
M48 - Delta Voltage: 380 to 480 VAC ± 15%
45 to 65 Hz
M48 - Star Voltage: 220 to 277 VAC ± 15%
45 to 65 Hz
Rated operational power
DPB01CM23, PPB01CM23 13 VA @ 230 ∆VAC, 50 Hz
DPB01CM48, PPB01CM48 13 VA @ 400 ∆VAC, 50 Hz
Supplied by L1 and L2
Supply Specifications
Power ON delay 1 s ± 0.5 s or 6 s ± 0.5 s
Reaction time
Incorrect phase sequence or
total phase loss < 200 ms
Voltage level (input signal variation from
-20% to +20% or from
+20% to -20% of set value)
Alarm ON delay < 200 ms (delay < 0.1 s)
Alarm OFF delay < 200 ms (delay < 0.1 s)
Accuracy (15 min warm-up time)
Temperature drift ± 1000 ppm/°C
Delay ON alarm ± 10% on set value ± 50 ms
Repeatability ± 0.5% on full-scale
Indication for
Power supply ON LED, green
Alarm ON LED, red (flashing 2 Hz
during delay time)
Output relay ON LED, yellow
Environment
Degree of protection IP 20
Pollution degree 3 (DPB01), 2 (PPB01)
Operating temperature
@ Max. voltage, 50 Hz -20 to 60°C, R.H. < 95%
@ Max. voltage, 60 Hz -20 to 50°C, R.H. < 95%
Storage temperature -30 to 80°C, R.H. < 95%
Housing dimensions
DIN-rail version 22.5 x 80 x 99.5 mm
Plug-in version 36 x 80 x 94 mm
Weight Approx. 120 g
Screw terminals
Tightening torque Max. 0.5 Nm
according to IEC 60947
Approvals UL, CSA
CE Marking Yes
EMC Electromagnetic Compatibility
Immunity According to EN 61000-6-2
Emissions According to EN 50081-1
General Specifications

Specifications are subject to change without notice (09.05.05) 3
DPB01, PPB01
Adjust the input range set-
ting the DIP switches 3 and
4 as shown below.
Select the desired function
setting the DIP switches 1
and 2 as shown below.
To access the DIP swiches
open the grey plastic cover
as shown below
Selection of level and time
delay:
Upper knob:
Setting of lower level on rel-
ative scale.
Centre knob:
Setting of upper level on rel-
ative scale.
Lower knob:
Setting of delay on alarm
time on absolute scale (0.1
to 30 s).
Function/Range/Level and Time Delay Setting
Power ON delay
ON: 6 s ± 0.5 s
OFF: 1 s ± 0.5 s
Monitored voltage
ON: Phase-Neutral
OFF: Phase-Phase
Measuring range
SW3 ON ON OFF OFF
SW4 ON OFF ON OFF
M23 Ph-Ph 208 VAC 220 VAC 230 VAC 240 VAC
Voltage
M48 Ph-Ph 380 VAC 400 VAC 415 VAC 480 VAC
Voltage DPB01 only
M48 Ph-N 220 VAC 230 VAC 240 VAC 277 VAC
Voltage DPB01 only
Wiring Diagrams
L2 L3L1
L1
L2
L3
L2 L3L1
L1
L2
L3
Example 1
Example 2
L2
L3
m<3
U
L2
L3
m<3
U
15
16 18
15
16 18
N
N
N
N
µ
µ
675
L1
L2
L3
675
L1
L2
L3
Example 1
Example 2
L2
L3
m<3
U
L2
L3
m<3
U
1
1
4
4
3
3
N
11
N
11
µ
µ
DPB01 PPB01
µ
µ
µ
µ
L2
L1
L2
L1 L2
L1
L2
L1

4Specifications are subject to change without notice (09.05.05)
Upper Level
Hysteresis
Hysteresis
Lower Level
L1
L2
L3
Relay ON
Relay ON
Red L D ON
Red L D ON
L1 or
L1-L2
L2 or
L2-L3
L1 L2 L1
L2L1L3
L2 L3 L3
1 or 6 s
1 or 6 s
T T
1 or 6 s
L3 or
L1-L3
Operation Diagrams
Dimensions
22.5
80
83.5
99.5
63
28.5
DIN-rail Plug-in
36
80
94
28.5
63
90
*
*DPB01...N and PPB01...N don’t detect incorrect phase sequence.