CaRobotor Y Pro User manual
INSTRUCTION
MANUAL
Y Pro
CAR DASHBOARD FOR PATROL Y62
Welcome!
Thank you for purchasing this product, please read
the instructions carefully before use.
Let ’s see the wider world.
LIST
OVERVIEW
Display
Trouble
indicator lightCoolant & Battry
Y Pro Sync cable USB upgrade line
Oil meter
&
Oil pressure USB software
upgrade cable
Power harness
interface
Video input
interface Expand
port
Front view Rear view
Press A to switch labels
Hold B key to lock/unlock
the current setting
Operating Tips
KEY OPERATION INTRODUCTION
Redefining the keys, you can use them
to manipulate the Y PRO's features.
Long press the B key to reset the body
state.
Press A key to switch the main interface.
Hold A key to pop up the [setting window]
Press B key to switch widgets.
0°0°
Y PRO SYSTEM UPGRADE
TOOL
STEPS DEMONSTRATION
Please format the U disk as the formation below firstly.
Firstly, you have to unzip the Carobotor_dashboard.zip file, and
then copy the update directory and PLATFORM_CARD.mxnmcu
file to your disk that is in the directory you unziped.
Please plug your U disk in the usb port of your dashboard,
then long press the A key as the picture shows , and short
press the A key to switch to System upgrade window .
Long press B key to lock the current window until a red frame appears on the current window
as picture 1 ,then release the B key and long press B key again until you can see the system will
restart upgrade.
When the progress bar is full, please remove the U disk and
the system will restart automatically within two minutes.
U DISK
CAPACITY: 8/16G
FAT32
32KB
FILE FORMAT:
UNIT:
System upgrade MCU upgrade Device Info
CaRobotor OS
v5.1
Long press “B”to update system!
System upgrade MCU upgrade Device Info
CaRobotor OS
v5.1
System will restart to upgrade...
Long press “B”to update system!
System upgrade MCU upgrade Device Info
CaRobotorOS
v5.1
Longpress “B”to update system!
(If the system can’t be automatically restart after 2 minute,
please pull out the key and press the lock button,then restart
the vehicle after 1 minute.)
<1>
<2>
<3>
<4>
Systemupgrade MCUupgrade DeviceInfo
CaRobotorOS
v5.1
Longpress “B”to update system!
1 2 3
update
PLATFORM_CARD.mxnmcu
flashing
Y PRO MCU UPGRADE
TOOL
STEPS DEMONSTRATION
Please format the U disk as the formation below firstly.
Firstly, you have to unzip the Carobotor_dashboard.zip file, and
then copy the update directory and PLATFORM_CARD.mxnmcu
file to your disk that is in the directory you unziped.
Please plug your U disk in the usb port of your dashboard,
then long press the A key as the picture shows , and
short press the A key to switch to UNIT upgrade window .
Long press B key to lock the current window until a red frame appears on the current window
as picture 1, then release the B key and long press B key again until you can see the two LED
panles at the left and right side of dashboard flash.When the LED panles stop to flash, it means
you update the MCU successfully.
When the upgrade is complete,please remove the
U disk,lock the car for 5 minutes and then turn it
off and restart.
U DISK
CAPACITY: 8/16G
FAT32
32KB
FILE FORMAT:
UNIT:
System upgrade MCU upgrade Device Info
CaRobotor UNIT
v4.3
Long press “B”to update MCU!
System upgrade MCU upgrade Device Info
CaRobotor UNIT
v4.3
MCU updateing...
Long press “B”to update MCU!
System upgrade MCU upgrade Device Info
CaRobotorUNIT
v4.3
Long press “B”to update MCU!
<1>
<2>
<3>
<4>
Systemupgrade MCUupgrade DeviceInfo
CaRobotorOS
v5.1
Longpress “B”to update system!
1 2 3
System upgrade MCU upgrade Device Info
CaRobotorUNIT
v4.3
Long press “B”to update MCU!
update
PLATFORM_CARD.mxnmcu
Unscrew the four parts shown in the
figure, unplug the original car meter,
and remove the car meter.
REMOVE THE ORIGINAL CAR METER
PART 1
Lower the steering wheel. Pull out the instrument cover.
<2>
<4>
Unplug the harness plug
behind the cover plate.
<3>
<1>
Y PRO INSTALLATION STEPS
lower
tool:Phillips screwdriver
Please connect the Port A of the sync line
to the car.And then please connect the one
of port B of sync line to Y Pro.
<1>
<3> <4> <5>
<2> Start the engine.
Connect the other port B end of the sync
line to original car meter.And then it will
start to synchronize.
When synchronization is complete,
be sure to turn off the engine and
unplug the sync line as prompted.
Start syncing.
SYNCHRONOUS UPDATE
PART 2
INSTRUCTIONS
BEFORE
OPERATION
Stop engin and keep
ACC off at least 25
seconds before you
remove your meter
include Y PRO and
original car meter
from your car.
Sychroninzing 66%
Port A Car
Y Pro
Port B
Synchronization line
ORIGINAL CAR METER
Please install the cover according to the
origina procedure.
<1> <2> <3>
Connect the USB interface cable to the Y Pro
and plug the car plug to Y Pro.
INSTALL Y PRO
PART 3
Car
Y Pro
After the Y PRO is installed, please
lock the car for 5 minutes.And then
turn it off and restart.
