Carrera Digital 124 Wireless+ User manual

V01-06
Packungsinhalt und Bahnlayout
Contents of package and track route
Contenu du paquet et configuration du circuit
Contenido de la caja y configuración del circuito
Conteúdo da embalagem e disposição da fita
Contenuto della confezione e configurazione del circuito
Inhoud van de verpakking en lay-out van de baan
Paketinnehåll och spårlayout
Pakkauksen sisältö ja radan muoto
Pakkens innhold og banelayout
Csomag tartalma és pálya-kialakítás
Zawartość opakowania i schemat toru
Obsah obalu a vzhľad dráhy
Obsah obalu a vzhled dráhy
Съдържание на опаковката и оформление на пистата
Περιεχόμενο συσκευασίας και διαμόρφωση πίστας
Conţinut pachet și schemă traiectorie
Indhold og baneopsætning
包装内容和轨道布局
パッケージ内容とレールレイアウト
패키지 내용 및 트랙 레이아웃
   
Ambalaj içeriği ve pist düzeni
Содержимое упаковки и схема трека
Carrera Toys GmbH · Rennbahn Allee 1 · 5412 Puch / Salzburg · Austria
Carrera Revell of Americas Inc. · Suite 307N · 197 Route 18 South · East Brunswick, NJ 08816 · USA
Carrera Revell UK Ltd. · Unit 10 · Old Airfield Industrial Estate · Cheddington Lane · Tring HP23 4QR · United Kingdom
A
20023633 DIGI124 FULLSPEED

Verpackungsinhalt · Contents of package · Contenu du carton · Contenido de la caja · Conteúdo
da embalagem · Contenuto della confezione · Verpakkingsinhoud · Innehållet i förpackningen
Pakkauksen sisältö · Innholdet i pakningen · A csomag tartalma · Zawartość opakowania
Obsah balenia · Obsah balení · Съдържание на опаковката · Περιεχόμενα συσκευασίας
Conţinutul ambalajului · Emballageindhold · 包装内容 · 梱包内容 · 포장내용물
· Ambalaj içeriği · Содержимое картона
Ausbauvorschläge · Proposals for extension · Suggestions d‘extension · Propuestas de ampliación
Propostas de expansão · Proposte di ampliamento · Uitbreidingsvoorstellen · Monteringsförslag
Rakennelmaehdotuksia · Strekningsforslag · Kiépítési javaslatok · Propozycje rozbudowy
Návrhy výstavby · Návrhy výstavby · Предложения за демонтаж · Προτάσεις επέκτασης
Propuneri de asamblare · Udvidelsesforslag · 多项扩充建议 · 拡張提案 · 기타 조립 예
· Genişletme önerileri · Предложения по расширению
1x
1x
2x1x
1x
202x
5x
55x
4x 2x
1x
6x
1x
1x
11x
1x 74 cm/29.13 inch
O
1x 120°/126 cm/49.60 inch
P
3x 180°/178 cm/70.08 inch
Q
C
D
F
E
12x
12x
12x I
K
6x6x GH
2x
2x
4x
NML
5x
SET
CHANNEL
A
B
20023633 + 20020601
The BMW logo and the BMW wordmark are trademarks of
BMW AG and are used under License.Officially licensed by AUDI AG.
O
P
Q
Q
Q
NN
NN
L
M
M
M
L
L
SET
CHANNEL
CCCC
C
C
C
C
C
D
D
D
D
D
D
D
D
D
DD
D
I
I
I
I
II
I
I
I
I
I
I
K K
K
K
K
KK
K
KK
K
K
G
G
G
G
G
HH
H
H
H
H
E
F
F
F
F
A
B
C
L
M
SET
CHANNEL
G
H
G
H
1x

Verpackungsinhalt
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standardgeraden
1 Control Unit
1 Carrera DIGITAL 124 Doppelweiche (2 Schienenteile)
1 Carrera DIGITAL 124 Weiche, rechts (2 Schienenteile)
12 Kurven 1/60°
2 WIRELESS+ Handregler
1 WIRELESS+ Empfänger
1 WIRELESS+ Doppelladeschale
2 LiPo-Akku für Handregler
1 Transformator
Außenrandstreifen für Kurven · Innenrandstreifen für Kurven
Randstreifenabschlussstücke · Fahrbahnstützen · Leitplanken
Fahrbahnverriegelungen · Ersatzschleifer · Zubehör
Bedienungsanleitung
Streckenlänge: 9,6 m
Aufbaumaße: 309 x 255 cm
Contents of package
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standard straights
1 Control Unit
1 Carrera DIGITAL 124 double lane change section (2 track parts)
1 Carrera DIGITAL 124 lane change section, right (2 track parts)
12 Curves 1/60°
2 WIRELESS+ Speed controllers
1 WIRELESS+ Receiver
1 WIRELESS+ Twin charging station
2 LiPo rechargeable battery for speed controller
1 Transformer
Outside shoulders for curves · Inside shoulders for curves
Shoulder end sections · Supports · Guard rails
Track section bolts · Replacement contacts
Accessories Instructions
Track length: 31.49 ft./ 9,6 m
Dimensions when assembled: 10.14 x 8.37 ft./ 309 x 255 cm
Contenu du carton
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Droites standard
1 Control Unit
1 Carrera DIGITAL 124 changement de voie double
(2 pièces de rail)
1 Carrera DIGITAL 124 changement de voie, à droite
(2 pièces de rail)
12 Virages 1/60°
2 Régulateurs de vitesse WIRELESS+
1 Récepteur WIRELESS+
1 Double station de chargement WIRELESS+
2 Batterie LiPo pour régulateurs de vitesse
1 Transformateur
Accotements extérieurs pour virages
Accotements intérieurs pour virages
Pièces de fermeture d‘accotement · Supports de voie
Glissières de sécurité · Verrouillages de voie
Tresses de rechange · Accessoires
Mode d‘emploiLongueur de parcours: 9,6 m
Encombrement: 309 x 255 cm
Contenido de la caja
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Rectas estándar
1 Control Unit
1 Carrera DIGITAL 124 aguja doble (2 piezas de carril)
1 Carrera DIGITAL 124 aguja, derecha (2 piezas de carril)
12 Curvas de 1/60°
2 Reguladores de velocidad WIRELESS+
1 Receptor WIRELESS+
1 Bandeja de carga doble WIRELESS+
2 Batería de polímero de litio para reguladores de velocidad
1 Transformador
Tiras marginales externas para curvas
Tiras marginales internas para curvas
Piezas terminales de la tira lateral · Apoyos para el carril
Vallas protectoras · Cierres de los carriles
Piezas de fricción de recambio · Accesorios
Instrucciones de servicio
Longitud de la pista: 9,6 m
Dimensiones: 309 x 255 cm
Conteúdo da embalagem
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Rectas padrão
1 Control Unit
1 Carrera DIGITAL 124 desvio duplo (2 segmentos de carril)
1 Carrera DIGITAL 124 desvio, direita (2 segmentos de carril)
12 Curvas 1/60°
2 Reguladores de velocidade WIRELESS+
1 Receptor WIRELESS+
1 Cavidade dupla de carregamento WIRELESS+
2 Bateria LiPo para o regulador de velocidade
1 Transformador
Marcações externas das curvas · Marcações internas das
curvas · Peças de remate da berma · Apoios da pista
Railes · Bloqueios das pistas · Escovas de substituição
Acessórios · Instruções de uso
Comprimento do percurso: 9,6 m
Dimensões de montagem: 309 x 255 cm
Contenuto della confezione
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Rettilineo standard
1 Control Unit
1 Carrera DIGITAL 124 Scambio doppio (2 pezzi di rotaia)
1 Carrera DIGITAL 124 scambio, destra (2 pezzi di rotaia)
12 Curve 1/60°
2 Regolatori della velocità WIRELESS+
1 Ricevitore WIRELESS+
1 Caricabatteria doppio WIRELESS+
2 Accumulatore LiPo per regolatori della velocità
1 Trasformatore
Bordi esterni della pista per curve · Bordi interni della pista per
curve · Terminali di bordi pista · Sostegni carreggiata Guardrail
Bloccaggi carreggiata · Contatti striscianti di ricambio · Accessori
Istruzioni per l’uso
Lunghezza percorso: 9,6 m
Dimensioni: 309 x 255 cm
Verpakkingsinhoud
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standaard rechte stukken
1 Control Unit
1 Carrera DIGITAL 124 dubbele wissel (2 spoordelen)
1 Carrera DIGITAL 124 wissel, rechts (2 spoordelen)
12 Bochten 1/60°
2 WIRELESS+ Snelheidsregelaars
1 WIRELESS+ ontvanger
1 WIRELESS+ dubbel oplaadstation
2 LiPo-accu voor snelheidsregelaars
1 Transformator
Buitenrandstroken voor bochten · Binnenrandstroken voor
bochten · Randstrookbegrenzingdelen · Rijbaansteunen
Vangrails · Rijbaanvergrendelingen · Reserveslepers
Toebehoren · Bedieningshandleiding
Trajectlengte: 9,6 m
Opbouwmaten: 309 x 255 cm
Innehållet i förpackningen
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standardraksträckor
1 Control Unit
1 Carrera DIGITAL 124 dubbelväxel (2 skendelar)
1 Carrera DIGITAL 124 växel, Höger (2 skendelar)
12 Kurvor 1/60°
2 WIRELESS+ Hastighetsregulatorer
1 WIRELESS+ mottagare
1 WIRELESS+ dubbelladdare
2 LiPo-batteri för hastighetsregulatorer
1 Transformator
Yttre sladdzoner för kurvor · Inre sladdzoner för kurvor
Avslutningsbitar till sladdzoner · Stödben · Skyddsräcken
Clips · Reservsläpskor · Tillbehör · Bruksanvisning
Banans längd: 9,6 m
Banans mått fullt monterad: 309 x 255 cm
Pakkauksen sisältö
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Vakiosuoraa
1 Control Unit
1 Carrera DIGITAL 124 kaksoisvaihde (2 rataosaa)
1 Carrera DIGITAL 124 vaihde, oik (2 rataosaa)
12 Mutkaa 1/60°
2 WIRELESS+ Nopeussäädintä
1 WIRELESS+ vastaanotin
1 WIRELESS+ kaksipaikkainen laturi
2 LiPo-akku nopeussäädintä
1 Muuntaja
Ulkoreunat mutkiin · Sisäreunat mutkiin · Reunojen
päätekappaleet · Ajoratatuet · Kaiteet · Ajoradan lukitukset
Varakontaktit · Varusteet · Käyttöohje
Radan pituus: 9,6 m
Asennusmitat: 309 x 255 cm
Innholdet i pakningen
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standard rette stykker
1 Control Unit
1 Carrera DIGITAL 124 Dobbel sporskifter (2 skinnestykker)
1 Carrera DIGITAL 124 sporskifter, høyre (2 skinnestykker)
12 Svinger 1/60°
2 WIRELESS+ Hastighetsjusteringer
1 WIRELESS+ Mottaker
1 WIRELESS+ Dobbeltlader
2 LiPo-akkumulator for hastighetsjusteringer
1 Transformator
Ytterkantmarkeringer for svinger · Innerkantmarkeringer for
svinger · Kantstripeavslutning · Banestøtter
Autovern · Skinnelåseklips · Reservebørster
Tilbehør · Bruksanvisning
Banelengde: 9,6 m
Monteringsmål: 309 x 255 cm
A csomag tartalma
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Standard egyenes
1 Control Unit
1 Carrera DIGITAL 124 kettős váltó (2 sínrész)
1 Carrera DIGITAL 124 váltó, jobb (2 sínrész)
12 Kanyar 1/60°
2 WIRELESS+ Sebességszabályozó
1 WIRELESS+ Vevő
1 WIRELESS+ Dupla töltő
2 LiPo akku a kézi szabályozókhoz
1 Transzformátor
Külső kerékszegélyek kanyarokhoz · Belső kerékszegélyek
kanyarokhoz · Külső kerékvető ívek · Útpálya támaszok
Szalagkorlátok · Útpálya reteszelések · Pótkefék · Tartozékok
Használati utasítás
Pályahossz: 9,6 m
Felépített méret: 309 x 255 cm
Zawartość opakowania
1 BMW M4 GT3 „Schubert Motorsport, No.37“
1 Audi R8 LMS „Team Abt Sportsline, No.7“
11 Proste standardowe
1 Control Unit
1 Carrera DIGITAL 124 zwrotnica podwójna (2 elementy szyn)
1 Carrera DIGITAL 124 zwrotnica, prawa strona ( 2 elementy szyn )
12 Zakręty 1 / 60°
2 WIRELESS+ Regulatory prędkości
1 WIRELESS+ Odbiornik
1 WIRELESS+ Pojemnik na dwie baterie
2 Akumulator litowo-polimerowy do regulatory prędkości
1 Transformator
Pobocza zewnętrzne zakrętów · Pobocza wewnętrzne zakrętów
Końcowe elementy pobocza · Wsporniki toru jezdnego
Ochronne bariery drogowe · Blokady toru jezdnego
Zastępcze szczotki stykowe · Akcesoria · Instrukcja obsługi
Długość odcinków: 9,6 m
Wymiary po zmontowaniu: 309 x 255 cm

B
Carrera Toys GmbH · Rennbahn Allee 1 · 5412 Puch / Salzburg · Austria
Carrera Revell of Americas Inc. · Suite 307N · 197 Route 18 South · East Brunswick, NJ 08816 · USA
Carrera Revell UK Ltd. · Unit 10 · Old Airfield · Industrial Estate · Cheddington Lane · Tring HP23 4QR · United Kingdom
V01-05 / 05.2022
Montage- und Betriebsanleitung
Assembly and operating instructions
Instructions de montage et d’utilisation
Instrucciones de uso y montaje
Instruções de montagem e modo de utilização
Istruzioni per il montaggio e l’uso
Montage- en gebruiksaanwijzing
Monterings- och bruksanvisning
Asennus- ja käyttöohjeet
Montajse- og bruksanvisning
Ősszeszerelési és használati útmutató
Instrukcja obsługi i montażu
Návod na montáž a pre prevádzkuo
Návod na montáž a pro provoz
Ръководство за монтаж и експлоатация
Mоνтάζ και Оδηγία χρήσης
Instrucţiuni de montaj şi de utilizare
Monterings- og driftsvejledning
安装和使用说明
取扱説明書取扱説明書の内容は予
조립과 작동 방법
Montaj ve işletme kılavuzu
Инструкция по монтажу и эксплуатации

9
Table of contents
Safety instructions 9
Declaration of Conformity 9
Contents of package 9
Technical advice for assembly 9
Important Information 10
Description 10
Before first use 10
Care of the battery 10
Assembly instructions 10
Guard Rails and Supports 10
Electrical connection 10
Car components 10
Connections Control Unit 11
Connecting the receiver 11
Connecting the charging unit 11
Charging the speed controllers 11
Binding process 11
Control elements Control Unit 11
Encoding/programming
of cars to the according speed controllers 11
Preparation of start 12
Points function 12
Light function on/off 12
Encoding/programming of Autonomous Car 12
Encoding/programming Pace Car 12
Display of position Autonomous and Pace Car 12
Setting of the cars´ basic speed 12
Setting of cars´ braking performance 13
Setting fuel tank capacity 13
Deactivating Settings Keys 13
Extended Pit Lane function 13
Sound ON/OFF 13
Reset function 14
Energy-saving mode 14
Replacement of double sliding contact and guide keel 14
Height adjustment car chassis 14
Changing the light board 14
Maintenance and care 15
Troubleshooting/Driving tips 15
Technical specifications 15
Requirement for FCC Part 15 15
Warnings 15
Welcome
Welcome to the Team Carrera!
These operating instructions contain important information regard-
ing the assembly and operation of your Carrera DIGITAL 124 race-
track. Please read them carefully and keep them in a safe place
afterwards. If you have any queries, please do not hesitate to
contact our distributor or visit our website:
carrera-toys.com
Please check the contents for completeness and possible transport
damage. The packaging contains important information and should
also be retained. We hope you will derive a lot of pleasure from your
new Carrera DIGITAL 124 track.
Safety instructions
• WARNING! Not suitable for children under 36 months. Danger of
suffocation due to small parts which may be swallowed. Caution:
risk of pinching caused by function.
• WARNING!
This toy contains magnets or magnetic components. Magnets at-
tracting each other or a metallic object inside the human body may
cause serious or fatal injuries. Seek medical attention immediately if
magnets are swallowed or inhaled.
• The transformer is not a toy! Do not short-circuit the transformer’s
connections! Note to parents: Regularly inspect the transformer for
damage to the cable, plug or housing! Only operate the toy with rec-
ommended transformers! The transformer may no longer be used
if it is damaged! Only operate the racetrack with a transformer! If
play is interrupted for longer periods, it is recommended to separate
the transformer from the power supply. Do not open transformer or
speed controller housings!
Important note to parents:
Transformers and power supply units are not suitable to be used as
toys. The use of such products needs to be constantly supervised
by the parents.
• Regularly check the track and cars for damage to cables, plugs
and housings! Replace defective parts.
• The car racetrack is not suitable for outdoor operation or operation
in wet locations! Keep away from liquids.
• Do not place any metal parts onto the track to avoid short-circuits.
Do not place the track in the immediate vicinity of delicate objects,
as these could be damaged by cars hurled from the track.
• Disconnect the plug before cleaning or servicing the racetrack!
Only use a damp cloth for cleaning, no solvents or chemicals. When
it is not in use, store the track in a dry and dust-protected location,
preferably in the original cardboard box.
• Do not operate race track at face- or eye-level – risk of injury due
to cars being catapulted off the track.
• Misuse of transformer can cause electrical shock.
• The toy is only to be connected to Class II equipment
bearing the following symbol.
• The toy must only be used with a transformer for toys.
• Not to be used with controllable transformers.
• If the supply cord is damaged, it must be replaced by the manu-
facturer, its service agent or similary qualified persons in order to
avoid danger.
Note:
The vehicles and the Control Unit may only be operated again in
a completely assembled condition. Assembly may only be carried
out by an adult. Children of 8 years and above, or persons with
reduced physical, sensory or mental capacity, or lack of experience
and knowledge may use this appliance under the condition that they
are supervised or instructed concerning the use of the appliance
and understand the associated risks. Children must not play with
the appliance. Cleaning and user maintenance must not be per-
formed by children without supervision. Instruct the child not to try
and recharge non-rechargeable batteries because of the danger of
explosion.
Declaration of Conformity
Hereby, Carrera Toys GmbH declares that the radio equip-
ment type “2,4 GHz WIRELESS+” is in compliance with Di-
rective 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
carrera-toys.com – Safety and Quality
Technical advice for assembly
SET
CHANNEL
1
2
3
4
5
67 8
8
1 Connecting track + Control Unit
2 WIRELESS+ Receiver
3 WIRELESS+ Twin charging station
4 Lane change section right input
5 Lane change section right output
6 Double lane change section input
7 Double lane change section output
8 Infrared sensor:
The infrared sensor MUST be located on the switch that
functions as the entry rail (dark diode).

10
Important Information
Carrera DIGITAL 124EXCLUSIV
Carrera DIGITAL 124 EXCLUSIV
Please note that Exclusiv (analog system) and Carrera DIGITAL
124/132 (digital system) involve two separate and completely inde-
pendent systems. We hereby expressly indicate that both systems
must be kept separate when setting up the track, i.e. no connecting
rail from Exclusiv may be used together with the connecting rail and
Control Unit of the Carrera DIGITAL 124/132, even if only one of the
two connecting rails (Exclusiv connecting rail or Carrera DIGITAL
124/132 connecting rail and Control Unit) is attached to the current
supply. Furthermore, no other Carrera DIGITAL 124/132 compo-
nents (switches, electronic lap counter, pit stop) may be built into an
Exclusiv course, i.e. via analog operation.
Non-compliance with the above information may result in damage or
destruction of the respective Carrera DIGITAL 124/132 components.
In this case no warranty may be claimed.
Description
WIRELESS+ is the latest new cordless racetrack delight for Car-
rera DIGITAL124 and Carrera DIGITAL 132. The 2.4 GHz radio
technology with frequency-hopping is free of interference and offers
a range of up to 15 metres. Thanks to powerful lithium polymer re-
chargeable battery, continuous play for up to eight hours is possible
and stand-by operation for over 80 days. WIRELESS+ in conjunc-
tion with DIGITAL 124 offers wireless freedom for up to four drivers
on the racetrack.
Before first use
Before first using the speed controller, the rechargeable battery
supplied 2 must be inserted in the controller. Unscrew the battery
compartment 1 on the underside of the speed controller.
Connect the battery plug into the socket in the speed controller and
put the battery in place in the compartment. Finally screw down the
cover of the battery compartment again. The battery is part-loaded
at the factory, but it should be charged completely before being
used for the first time.
2
1
1
Care of the battery
To make sure the battery performs well for as long as possible, the
following points should be observed regarding its care and storage.
•
Before first using them, new batteries should always be charged
fully.
• With a fully-charged battery, continuous play is possible for up
to eight hours. When the battery power is falling off, range of the
speed controller will diminish. As soon as you notice this, the battery
should be fully recharged.
• If it is not to be used for an extended period, remove the battery
and store the controller at room temperature (16-18 °C) in a dry
place. To prevent a deep discharge of the battery, the stored battery
should be charged every 2 to 3 months.
Assembly instructions
1 4
2 3
1 + 2 + 3 Before assembling please insert the connecting clips
in the track as shown in figure 1. Stick tracks together on a flat
base. Move the connecting clips according to figure 2 in direction
of the arrow until they audibly snap in. The connecting clip may also
be inserted later. The connecting clips can be removed into both
directions by simply pressing down the clamped nose (see fig. 3).
4 Fastening: To fasten the track sections on a board, it is nec-
essary to use the track section fasteners (Item no. 20085209, not
contained in the package).
Note:
Carpeting is not a suitable foundation on which to build the track be-
cause of static charging, formation of fluff and ready inflammability.
The Position Tower is suitably connected to the shoulder con-
necting section F or to the Adapter Unit ; the latter can be posi-
tioned at any place within the racetrack.
Guard Rails and Supports
1 2
3 4
1 Guard rails: Guard rail mounts are fitted by tilting them upwards
onto the verge of the track.
2 + 3 Supporting raised sections: The shank of the ball pivot is
to be inserted into the square slots provided on the underside of the
track. The supports can be made higher by using the extensions.
The pedestal of the supports can be screwed to a base if required
(screws not included).
4 Supporting steep curves:
Slanting supports of the right height are provided to support steep
curves. Fix the nonadjustable supports at the beginning and end of
the curves. Insert the heads of the supports in the round slots of the
underside of the track.
Electrical connection
1
1 Connect the transformer plug with the Control Unit.
Note: To avoid short-circuits and electrocution, the toy may not be
connected using foreign devices, plugs, cables or other objects for-
eign to this toy. The Carrera DIGITAL 124 car racetrack only works
properly with an original Carrera DIGITAL 124 transformer.
The PC interface (PC Unit) may only be operated together with the
original Carrera PC Unit.
The toy must be used with the accompanying transformer or power
supply unit if the transformer is included with the toy.
Car components
1
2
3
3
3
3
45
9
6
8
10
15
12
13
11
14 11
7
1 Body
2 Engine block
3 Tyres
4 Rear axle
5 Rear axle receptacle
including spacer plate
6 Front axle
7 Front axle mounting
8 Board
9 Central magnet
10 Rear magnet
11 Chassis
12 Rocker arm including spring
13 Guide keel with double sliding contact
14 Center magnet retainer
15 Fastening plate
Note: vehicle construction depends on the model.
The designation of the individual parts may not be used as
order numbers.

11
Connections (from left to right):
1 Connection for Lap Counter 20030342
2 Connection for Carrera AppConnect 20030369, PC-Unit or
Lap Counter 20030355
3 Connector 1 for speed controller, speed controller extension set
or WIRELESS+ receiver
4
Connector 2 for WIRELESS Tower 200 10108
5 Connector 3 for speed controller
6 Connector 4 for speed controller
7 Connection for DIGITAL 124 / DIGITAL 132 power supply
General information on connectors 1-4:
When a WIRELESS+ receiver is used, it must be plugged into con-
nector 1. Optionally a WIRELESS Tower 20010108 can be plugged
into connector 2. When only the WIRELESS+ receiver is used, con-
nector 2 is to be left empty.
Additional wired speed controllers may be plugged into connectors
3 and 4. Please note that these will use address 5 and 6 then.
Using the speed controller extension set 20030348 it has to be
plugged into connector 1. The cars´ addresses will be allocated as
follows:
• Speed controller extension set = address 1, 3 and 4
• connector 2 = address 2
• connector 3 = address 5
• connector 4 = address 6
Note:
a combination of WIRELESS and speed controller extension set is
not possible!
Please note that in DIGITAL 124 the number of cars is restricted
to four.
Connections Control Unit
1 52 63 74
Connecting the receiver
Connect the receiver according to the symbol to either of the two
sockets on the control unit which are marked Tower 1 and Tower 2.
For operating four WIRELESS+ speed controllers only one 2.4 GHz
receiver is required.
Symbols
SET
CHANNEL
Connecting the charging unit
The charging unit is connected at the rear of the control unit. To site
the charging unit at any other place on the track, an adapter unit
20030360 will be needed.
Rear view of the
control unit
Charging the speed controllers
Before first being used, the WIRELESS+ speed controllers should
be fully charged. Place the speed controllers in the charging station
and switch on the control unit. While the unit is charging, the LEDs
1 on the speed controllers will flash. When charging is completed,
the LEDs 1 will light up continuously.
When using a lithium polymer rechargeable battery, it is possible to
top up the speed controller at any time.
1 1
Binding process
2
SET
CHANNEL
1
2
3
1
SET
CHANNEL
1
4
2
1
3
SET
CHANNEL
1
2
3
Before the speed controller can be used to control the cars, it must
be “bound” to the receiver.
To do this, switch on the control unit.
1
The receiver indicates it is ready for operation by a revolving light
signal in the segment display 1.
2
Push the “SET” button 2 once until the figure 1 appears in the seg-
ment display 1. The number shown is then the address of the car.
Switch to the next address by further pressing the button.
Now press the binding button 3 on the top of the speed controller.
The speed controller signals a successful binding process with
flashing of the LED, while the receiver indicates it by revolving lights
in the segments. The binding process is now complete and the
speed controller is ready for use.
3
To bind the second speed controller, follow the same procedure.
Press the “SET” button 2 on the receiver twice, until the figure
2 appears 1. Then press the binding button 3 on the second
speed controller.
4
To display the address set for the speed controller, press once on
the binding button 2 on the top of the speed controller.
The LED 1 will then flash, according to the address set.
If the speed controller is not actuated, it switches automatically after
about 20 seconds into energy-saving mode. The speed controller
can be reactivated by pressing the tappet or the lane-change button.
Control elements Control Unit
1
8
2
7
3
6
4
5
1 On/off switch
2 Switch for fuelling function
3
Button to start the race / acknowledge programming
4 Button for Pace Car / termination of programming
5 Button for setting basic speed
6 Button for setting braking performance
7 Button for setting fuel tank capacity
8 Programming button for cars
General operating information
Some buttons are assigned with different tasks. In order to set a
function you need to use key combinations. Any programming steps
can be cancelled with button 4 “ESC/PACE CAR″. You will find
further details in the course of this manual.
Encoding/programming
of cars to the according
speed controllers
1
8
2
7
3
6
4
5
1 2
1x
3 4
To encode a car place it on the track and swich on the Control Unit.
Press “Code” button once 8, fig. 1; the first LED starts to light,
fig. 2. Then push lane-change-button once on the relevant speed
controller, fig. 3. In case the car is equipped with lights they will
start to flash and the Control Unit´s LEDs 2-4 will light successively.
Once encoding has been carried out the middle LED lights perma-
nently (fig. 4) and the car is allocated to the speed controller.
Note: This kind of encoding requires to only have the car on the
racetrack which shall be encoded.

12
Preparation of start
1 2
This Carrera DIGITAL 124 vehicle ideally matches the Carrera track
system scale 1:24.
1 + 2 Optimally setting up the grinders:
To ensure proper and continuous driving, slightly fan out the ends
of the contact brushes 1 and bend them towards the track as per
fig. 2. Only the end of the contact brush should have contact to the
track and may be cut off slightly in case of wear. Dust and abrasion
should be removed from track material and sliding contacts from
time to time.
During operation small car parts as spoilers or mirrors may get off or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.
Points function
1
2
1 Make sure that the car’s guide keel is located inside the track slot
and that the double sliding contact is in contact with the current
carrying track.
Place the cars onto the connecting track.
2 When changing lanes, you must keep the button on the
speed controller depressed until the car has passed the point.
Light function on/off
3 sec.
STOP
The car programmed to the speed controller will have to come to a
stop for at least 3 seconds before the light can be switched on or off
by the push of the lane-change-button.
Note:
applies only to models fitted with lighting
Encoding/programming
of Autonomous Car
1
8
2
7
3
6
4
5
1 2
2x
3 4
300
150
250
200
0
100
50
SPEED
+
CLICK
5
Switch on the Control Unit, place the car to be encoded on the track
and press „Code“ 8 twice, fig. 1. The first two LEDs at the Con-
trol Unit start to light, fig. 2. Now push the lane-change button at
the speed controller, fig. 3; LEDs 3-5 will light successively. Wait
until the middle LED lights again, fig. 4. Activate the speed
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fig. 5.
Autonomous Car´s encoding is completed now.
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Autono-
mous Car will be maintained unless the car is not being recoded.
The Autonomous Car is always displayed with address 7 in combi-
nation with the Position Tower.
Encoding/programming
Pace Car
Pit Lane 20030356
1
8
2
7
3
6
4
5
2
3x
1
3 4
300
150
250
200
0
100
50
SPEED
+
CLICK
5
(only in combination with Pit Stop Lane #20030356)
Switch on the Control Unit, place the car to be encoded on the track
and press “Code″ 8 three times, fig. 1. The first three LEDs at
the Control Unit start to light, fig. 2. Now push the lane-change but-
ton at the speed controller, fig. 3; LEDs 2-5 will light successively.
Wait until the middle LED lights again, fig. 4. Activate the speed
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, fig. 5. The Pace Car´s encoding is
completed now and the car enters the Pit Stop Lane.
Note: This kind of encoding requires having only the car on the
track which is to be encoded. The programming of the Pace Car
will be maintained unless the car is not being recoded. The Pace
Car is always displayed with address 8 in combination with the Posi-
tion Tower.
Extended Pace Car function
After the Pace Car´s encoding has been completed it will auto-
matically enter the Pit Lane during the first laps. In order to start the
Pace Car please push the button “Pace Car” 4 once. The LEDs
2 and 3 at the Control Unit will light and the Pace Car will leave the
Pit Lane. The Pace Car will now drive as long as the button „Pace
Car“ is pushed again. LED 2 stops lighting and the car automatically
enters the Pit Lane within the current lap.
Display of position
Autonomous and Pace Car
1
8
2
7
3
6
4
5
1
Position
Tower
20030357
1
8
2
7
3
6
4
5
3
1
8
2
7
6
4
5
2
(only in combination with Position Tower #20030357)
The position of the Autonomous Car (address 7) and of the Pace
Car (address 8) can be displayed at the Position Tower. This func-
tion can be activated at the Control Unit. Therefore switch off the
Control Unit and keep the “BRAKE” button 6 pushed, fig. 2,
switch on the racetrack and release the “BRAKE” button again. By
pushing the button again the function may be changed:
1 LED lights = no display
2 LEDs light = display at the Position Tower
Set the function requested and confirm your choice via “START/
ENTER”.
Setting of the
cars´ basic speed
1 – 10
1 – 10
1 2
1
8
2
7
3
6
5
4
1
8
2
7
3
6
4
5
3
6
1
8
2
7
3
6
4
5
5
The setting of the basic speed can be effected individually for one
and/or several cars. The cars which are to be adjusted have to be
positioned on the track. The setting can be carried out on 10 levels
with the 5 LEDs indicating the different levels by flashing or perma-
nent lighting.
1 1 LED lights = low speed
2 5 LEDs light = high speed
Switch on the Control Unit, place the cars to be adjusted on the
track and press “SPEED” 5 once. A certain number of LEDs will
now light, showing the speed level last used. Push the “SPEED”
button 5 as many times until you have reached the speed desired.
Confirm by pressing “ENTER/START” 3. A short running light and
the lighting of the middle LED confirms completion of the setting,
fig. 6.

13
Setting of cars´
braking performance
1 – 10 1 – 10
1 2
1
8
2
7
3
6
5
4
1
8
2
7
3
6
4
5
3
6
1
8
2
7
3
6
4
5
5
(only for cars operated with speed controllers)
The setting of the braking performance can be effected individually
for one and/or several cars. The cars which are to be adjusted have
to be positioned on the track. The setting can be carried out on 10
levels with the 5 LEDs indicating the different levels by flashing or
permanent lighting.
1 1 LED lights = low braking effect
2 5 LEDs light = high braking effect
Switch on the Control Unit, place the cars to be adjusted on the
track and press “BRAKE” 6 once. A certain number of LEDs will
now light, showing the brake step last used. Push the “BRAKE” but-
ton 6 as many times until you have reached the braking perfor-
mance desired. Confirm by pressing “ENTER/START” 3. A short
running light and the lighting of the middle LED confirms completion
of the setting, fig. 6.
Setting fuel tank capacity
1 – 10
1 – 10
1 2
1
8
2
7
3
65
4
1
8
2
7
3
6
4
5
3
6
1
8
2
7
3
6
4
5
5
(only for cars operated with speed controllers)
The setting of the fuel tank capacity in combination with the Pit Lane
(20030356) is effected for all cars simultaneously. The setting can
be carried out on 10 levels with the 5 LEDs indicating the different
levels by flashing or permanent lighting.
1 1 LED lights = low fuel capacity
2 5 LEDs light = full tank
Switch on the Control Unit, place the cars to be adjusted on the
track and activate the fuelling function by means of the slide switch
2, fig. 3. Press the “FUEL” button 7 once. A certain number of
LEDs will now light, showing the fuel capacity last used. Push the
“FUEL” button 7 as many times until you have reached the fuel
capacity desired. Confirm by pressing “ENTER/START” 3. A short
running light and the lighting of the middle LED confirms completion
of the setting, fig 6.
Extended fuelling function
You can choose between 3 modes via the sliding switch 2,
fig. 3:
• OFF = cars don´t consume any “petrol”
• ON = cars consume “petrol”
• REAL = maximum speed depending on fuel tank capacity / cars
consume “petrol”) (only in combination with Pit Lane 20030356 or
Pit Stop Lane 20030346 and Pit Stop Adapter Unit 20030361)
When driving in “REAL-mode” the car with a full tank is “heavier”,
drives slowlier and shows a lower braking effect; a car with an empty
tank is “lighter”, drives faster and shows a higher braking effect. The
current fuel tank capacity and the “fuel consumption” can only be
displayed in combination with the Driver Display 20030353 and Pit
Stop 20030356.
Refuelling of cars with Pit Lane 20030356
and Driver Display 20030353
Pit Lane 20030356 Driver Display 20030353
87
910
The car´s present tank capacity can be read via the bar display with
5 green and 2 red LEDs at the Driver Display. For refuelling drive
your car into the Pit Lane across the refuelling sensor fig. 7. The
bar display now starts to flash, fig. 8, and the car can be refuelled
by keeping the lane-change button pushed. fig. 9. The number of
refuellings are indicated by flashing or lighting of the yellow LEDs,
fig. 10 (also see Driver Display).
Note: cars with an empty tank are disregarded for lap-counting
in combination with Position Tower 20030357.
Setting of tank capacity at the start of the race
Pit Lane 20030356 Driver Display 20030353
1
8
2
7
3
6
4
5
11 12
1413
(only in combination with Pit Lane 20030356 and Driver Display
20030353)
Irrespective of the basic setting of the tank capacity it is possible
to individually set the tank capacity for one or several cars at the
race´s start for the number of laps till the first pit stop. Push “START/
ENTER” once 3; the 5 LEDs at the Control Unit will light perma-
nently, fig. 12 , and the Driver Display´s bar display will flash, fig. 13 .
Clicking the lane-change button at the corresponding speed control-
ler enables you to change the fill level, fig. 14 .
Deactivating Settings Keys
8
7
3
6
4
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
4
5
3
To deactivate the keys for setting Speed, Brake and Fuel, proceed
as follows: Hold down the Code Key:
While holding down the Code Key 8, turn on the Control Unit and
then release the Code Key. To reactivate the above keys, repeat the
procedure just described.
Extended Pit Lane function
Pit Lane 20030356
1
8
2
7
3
6
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
5
4
1
8
2
7
3
6
4
5
3
1
8
2
7
3
6
4
5
6
5
(only in combination with Pit Lane 20030356)
It is possible to activate/deactivate the lap counting function in the Pit
Lane 20030356 or Pit Stop Lane 20030346 with the Pit Stop Adapter
Unit 20030361. Switch off the Control Unit, keep “SPEED” button 5)
pushed, switch on Control Unit and release “SPEED” button 5.
By pushing the button again, 1 or 2 LEDs will light depending on
the setting.
• LED 1 = lap counting function deactivated
• LED 1 + 2 = lap counting function activated
Select the desired setting and push or drive a car across the Pit
Lane Sensor, fig. 5. The settings will now be adopted. Push
“START/ENTER” 3 for leaving the settings again.
Sound ON/OFF
1
8
2
7
3
6
4
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
4
5
3
The confirmation sound when crossing the sensors and the key
sound can be switched off. Switch off the Control Unit and keep the
“START/ENTER” button 3 pushed, switch on the racetrack and
release “START/ENTER” 3 again. The acknowledgement sound
for switching on the Control Unit cannot be switched off however.

14
Reset function
1
8
2
7
3
6
4
5
2
1
8
2
7
3
6
4
5
1
1
8
2
7
3
6
4
5
3
To restore the Control Unit to factory settings the Control Unit offers
a reset function.
Switch off the Control Unit and keep the “ESC/PACE CAR” 4 but-
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaffected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to ener-
gy-saving mode and all displays such as Position Tower, Driver
Displays and Startlight are turned off. To reactivate the controller,
switch it off for 2 or 3 seconds, then switch it on again. All settings
will be kept.
Replacement of double
contact brushes and guide keel
1 2
43
In case the car is lifted, the rocker bar folds up slightly (fig. 1).
For changing the guide keel or the double contact brushes the
rocker bar can be folded up widely according to fig. 2.
3 For changing the guide keel and the double contact brushes the
guide keel should be removed first.
4 Afterwards both double contact brushes can be removed and
changed. Please take care that in stage one the upper contact
brush 4 a is only pulled out partly and in stage two the double
contact brush is pulled out completely with the contact brush 4 b
For inserting please proceed the same way.
Height adjustment
car chassis
1 2
3 4
Before you can begin adjusting the chassis and the magnets it is
necessary to detach the car body from the vehicle. Remove the
mounting screws on the underside of the car and lift off the car body.
Adjusting the height of the front axle
1 Remove the two screws from the front axle mounting and detach
the entire front axle including the mounting from the chassis. 2
Detach the mounting from the axle, turn it through 180 degrees 3
and insert the axle back into the mounting 4. Now you can return
the front axle and mounting unit to the chassis.
1 2
3 4
5
Adjusting the height of the rear axle
To simplify the procedure, carefully detach the plug connection bet-
ween the motor and the circuit board 1. Remove the two screws
from the motor block unit and detach the magnet retainer from the
chassis. Now remove the two rear screws and detach the entire
motor block 2.
Turn the motor block around and remove the two screws from the
rear axle mounting. Remove the spacer plates and the rear axle unit
including the mounting 3. To adjust the height, place the spacer
plate in the motor block 4 and tighten the screws of the rear axle
unit. 5.
1
2 3
Adjusting the central magnet
If required, the central magnet can also be adjusted. Remove the
magnet unit from the chassis in its entirety 1, turn it horizontally by
180 degrees 2 and return it to the chassis. Then mount the magnet
retainer 3 and restore all plug connections.
Note: Height adjustment car chassis – Dependent on model
Changing the light board
1 32
4 65
7
ATTENTION! Depending on the model, the light boards might be
screwed tight.
Front light: To change the light boards unscrew the car’s upper
part from the chassis. Unscrew the front axle according to fig. 1
and remove the cables between the front light and the car board (fig.
2). Slightly bend down the catch hook (fig. 3) and pull up the light
board. Insert the light board (fig. 4), until the catch hook latches
in. Screw in the front axle and fit the cables together according to
their colours.
Rear light: Remove the cables between the rear light and the car
board according to fig. 5 Slightly bend down the catch hook (fig.
6) and pull up the light board. Insert the light board until the catch
hook latches in (fig. 7) and fit the cables together according to
their colours.