Carrier 42QTD024DS Series User manual

CASSETTE TYPE AIR CONDITIONER
INSTALLATION MANUAL
G B
ENGLISH
INSTALLATION MANUAL
I
ITALIANO
MANUALE DI INSTALLAZIONE
F
MANUEL D'INSTALLATION
D E
INSTALLATIONSHANDBUCH
DEUTSCH
E
MANUAL DE INSTALACIÓN
N L
INSTALLATIEHANDLEIDING
NEDERLANDS
FRANÇAIS
ESPAÑOL
P L
POLSKI
INSTRUKCJA MONTAŻU

The manufacturer reserves the right to change any product specifications without notice.
This producthas been determinedto be incompliance with the Low Voltage Directive (2006/95/EC),
and the Electromagnetic Compatibility Directive (2004/108/EC)ofthe European Union.
Indoor Unit Outdoor Unit Rated Voltage & Hz
42QTD024DS*
42QTD036DS*
42QTD048DS*
42QTD060DS*
38QUS024DS*
38QUS036DS*
38QUS048DT*
38QUS060DT*
220-240V ~ 50Hz
380-420V 3N~ 50Hz
845x320x700
945x395x810
938x392x1369
Dimension(IDU)
840x840x245
840x840x245
Dimension(ODU)
840x840x287
840x840x287 938x392x1369
GB-1
CorrectDisposal ofThis Product
(Waste Electrical & Electronic Equipment)
(Whenusingthis air conditioner inEuropeancountries, the followingguidance mustbe followed)
- This marking shown on the product or its literature, indicates that waste electrical and eletrical equipment (WEEE as in
directive 2002/96/EC) should not be mixed with general household waste.
It is prohibited to dispose of this appliance in domestic household waste.
For disposal, there are several possibilities:
1. The municipality has established collection systems, where electronic waste can be disposed of at least free of charge to
the user.
2. When buying a new product, the retailer will take back the old product at least free of charge.
3. The manufacture will take back the old appliance for disposal at least free of charge to the user.
4. As old products contain valuable resources, they can be sold to scrap metal dealers.
Wild disposal of waste in forests and landscapes endangers your health when hazardous substances leak into the
ground-water and find their way into the food chain.
ThisproductcontainsfluorinatedgasescoveredbytheKyotoProtocol
Chemical Name ofGas
Global Warming Potential (GWP) of Gas
R410A
2088
CAUTION
1. Paste the enclosed refrigerant label adjacent to the charging
and/or recovering location.
2. Clearly write the charged refrigerant quantity on the
refrigerant label using indelible ink.
3. Prevent emission of the contained fluorinated gas. Ensure
that the fluorinated gas is never vented to the atmosphere
during installation, service or disposal. When any leakage
of the contained fluorinated gas is detected, the leak shall
be stopped and repaired as soon as possible.
4. Only qualified service personnel are allowed to access and
service this product.
5. Any handling of the fluorinated gas in this product, such as
when moving the product or recharging the gas, shall comply
under (EC) Regulation No. 842/2006 on certain fluorinated
greenhouse gases and any relevant local legislation.
6. Contact dealers, installers, etc., for any questions.

CONTENTS
3
3
4
5
5
7
7
8
9
10
10
10
11
11
11
12
12
12
13
13
13
14
14
15
17
17
17
17
1. PREPARING FOR INSTALLATION ······································································
1.1 Safety Percautions ·························································································
1.2 Accessories ··································································································
2. INDOOR UNIT INSTALLATION ···········································································
2.1 Installation Site Choosing ················································································
2.2 Install The Suspension Bolts ············································································
2.3 Handing The Indoor Unit ··················································································
2.4 Install The Drain Pipe ·····················································································
2.5 Install The Panel ····························································································
3. OUTDOOR UNIT INSTALLATION ······································································
3.1 Installation Site Choosing ················································································
3.2 Outdoor Unit Mounting Dimension ·····································································
3.3 Space Requirement For Outdoor Unit ·································································
3.4 Install The Outdoor Unit ················································································
3.5 Install The Drain Pipe For Outdoor Unit ······························································
4. REFRIGERANT PIPING WORK ··········································································
4.1 Flaring ·······································································································
4.2 Piping Work ·································································································
4.3 Refrigerant Pipe ··························································································
4.4 Air Evacuation ····························································································
4.5 Leakage Test ······························································································
5. WIRING ···········································································································
5.1 Power From Outdoor Site ···············································································
5.2 Independence Power Supply ···········································································
6. FINAL CHECK AND TRAIL OPERATION ····························································
6.1 Final Check List ····························································································
6.2 Manual Operation ·························································································
6.3 Trail Operation ·····························································································
7
GB-2

GB-3
1. PREPARING FOR INSTALLATION
1.1 SAFETY PRECAUTIONS
WARNING
This symbol indicates the possibility of personnel injury or loss of life.
Installing, starting up, and servicing air-conditioning equipment can be hazardous due to system
ressures, electrical components, and equipment location (roofs, elevated structures, etc.).
Only trained, qualified installers and service mechanics should install, start-up, and serve this equipment.
When working on the equipment, observe precautions in the literature and on tags, stickers, and labels
attached to the equipment.
Follow all safety codes. Wear safety glasses and work gloves. Keep quenching cloth and fire extinguisher
nearby when brazing. Use care in handing, rigging, and setting bulky equipment.
Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to
the unit. Consult local building codes and National Electrical Code for special requirement.
Refrigerant gas is heavier than air and replaces oxygen.A massive leak could lead to oxygen
depletion, especially in basements, and an asphyxiation hazard could occur leading to serious
injury or death.
When the air conditioner is installed in a small room, provide appropriate measures to ensure that
the concentration of refrigerant leakage occur in the room does not exceed the critical level.
If the refrigerant gas leaks during installation, ventilate the area immediately.
Refrigerant gas may produce a toxic gas if it comes in contact with fire such as from a fan heater, stove or cooking device.
Exposure to this gas could cause severe injury or death.
Disconnect from power source before attempting any electrical work. Connect the connective cable
correctly.
Wrongly connecting may result in electric parts damaged.
Use the specified cables for electrical connections and attach the wires firmly to the terminal block
connecting sections so that the external force is not exerted to the terminal.
Be sure to provide grounding.
Do not ground units to gas pipes, water pipes, lightning rods or telephone wires. Incomplete grounding could cause a severe
shock hazard resulting in injury or death.
Safely dispose of the packing materials.
Packing materials, such as nails and other matal or wooden parts, may cause stabs or other injuries. Tear apart and throw away
plastic pacaging bags so that children will not play with them. Children playing with plastic bags face the danger of suffocation.
Do not install unit near concentrations of combustible gas or gas vapors.
Be sure to use the supplied or exact specified installation parts.
Use of other parts may cause the unit to come to lose, water leakage, electrical shock, fire or equipment damage.
When installing or relocating the system, do not allow air or any substances other than the
specified refrigerant (R410A) to enter the refrigeration cycle.
This appliance is not accessible to the general public and intended to be maintained by qualified
service personnel and located at a level not less than 2.5m from floor.
Electrical work should be carried out in accordance with the installation manual and the national,
state and local electrical wiring codes.
Be sure to use a delicated power circuit. Never share the same power outlet with other appliance.

7
GB-4
1. PREPARING FOR INSTALLATION
WARNING
CAUTION
This symbol indicates the possibility of property damage or serious consequences.
1.2 ACCESSORIES
The following accessories are supplied with the unit. The type and quantity may differ depending on the specifications.
WARNING
Never modify this unit by removing any of the safety guards or bypassing any of the safety
interlock switches.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must
not be supplied through an external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
Use the prescribed cables for electrical connection with insulation protected by insulation
sleeving having an appropriate temperature rating.
Unconformable cables can cause electric leak, anomalous heat prodcution or fire.
To avoid personal injury, be careful when handling parts with sharp edges.
Do not install the indoor or outdoor units in a location with special environmental conditions.
Do not install in a place that can amplify the noise level of the unit or where noise and discharged
air might disturb neighbors.
Perform the drainage/piping work securely according to the installation manual.
Improper drain piping may result in water leakage and property damage.
Do not instal the air conditioner in the following places.
-The place where there is mineral oil or arsenic acid.
-The place where corrosive gas (such as sulfurous acid gas) or combustible gas (such as thinner)
can accumulate or collect, or where volatile combustible substances are handled.
-The place there is equipment that generates electromagnetic fields or high frequencey harmonics.
3
1
1
Name of Accessories
Manual
Pipe insulation material
Insulation
Q‘ty(pc) Shape Use
2
1
<Installation manual>, <User manual>,
<Remote controller manual> (or
<Wired controller manual>)
Drain outlet
Connect drainage hose for outdoor unit.
Gasket
Seal the drainage outlet for outdoor unit.
Clamp filter
For conforming to EMC standards
(Used for Indoor power cord and
indoor/outdoor connecting wires)
Flexible hose 1
Drainage
Pipe clamp
1
Fix the flexible hose to indoor unit.

72GB-5
1. PREPARING FOR INSTALLATION
2.1 INSTALLATION SITE CHOOSING
INDOOR UNIT
■ Where it is out of direct sunlight.
■ Where the airflow is not blocked.
■ Where an optimum air distribution is ensured.
■ Where the condensate can drain correctly and safely.
■ Install the indoor unit on a wall/ceiling that prevents vibration and is strong enough to hold the product weight.
■ Maintain sufficient clearance around the indoor unit for maintenance and servicing.
■ Where the air filter can be removed and cleaned easily.
■ Where the piping between the indoor and outdoor units is within the allowable limits.
■ Install the indoor unit 1m or more away from the TV or radio to prevent the screen from being distorted or noise from
being generated.
■ Install the indoor unit as far away as possible from fluorescent and incandescent lights so that the remote control can
be operated well.
1
Name ofAccessories Q‘ty(pc)
1
Shape Use
To remote control the air conditioner
2
Battery
Tapped screw
Remote controller holder To hold the remote controller on the wall
For remote controller
2
Remote Controller
To fix the remote controller holder
Note: The accessories related to remote controller will be unavailable for the models with wired
controller. For wired controller accessories, please refer to attached manual of wired controller.
The following accessories are related to remote controller.
2. INDOOR UNIT INSTALLATION
Separate packed parts
Name ofAccessories Q‘ty(pc)
1
Shape Use
To remote control the air conditioner Panel

GB-6
SPACE REQUIREMENT FOR INDOOR UNIT
The size of Outline dimension
Unit: mm
2. INDOOR UNIT INSTALLATION
Clearance from the wall or other obstacles
Connecting port
of refrigerant pipe
Connecting port
of drain pipe
Connecting port
of drain pipe
Connecting port
of refrigerant pipe
Dimension
287 >317
AH
048/060
245 >275
024/036
Model
(42QSM)
Fresh air intake ( Φ75mm)
80mm
80mm
Ø75mm
MODEL (QTD024-060)

2. INDOOR UNIT INSTALLATION
2.2.1 Mark the spots on the ceiling where you want to install the indoor unit.
2.2.2 Drill holes at the marking spots and then insert bolt anchors. Use existing ceiling supports or construct a suitable support.
NOTE
Use a hole-in-anchor, sunken insert for existing ceilings.
2.2.3 Install the suspension bolts (use W3/8 or M10 suspension bolts, 4 pieces) depending on the ceiling type.
2.2 INSTALL THE SUSPENSION BOLTS
7GB-7
2.3.2 Hang the indoor unit to the suspension bolts between two nuts.
2.3.3 Screw the nuts to suspend the unit. Check the lower side of indoor unit locates at position (10 to 12 mm) higher than the
lower surface of the ceiling. L is about half of the screw length of the installation hook.
2.3.4 Adjust level of the unit by using level vial to make sure horizontal level of the main body within ±1°.
It is recommended to install the Y joint before installing the indoor unit
When moving the unit during or after unpacking, make sure to lift by holding its hooks.
Do not exert any pressure on other parts, especially the refrigerant piping and drain piping.
CAUTION
2.3 HANGING THE INDOOR UNIT
2.3.1 Screw double nuts to each suspension bolts making space for hanging the indoor unit.
Screw nut
Washer
Hanging
screw bolt
Overhang part
Shockproof cushion
Concrete
Suspension bolt(
3/8” orM10)-field supply
Hole in anchor
Hole in plug
Insert
Ensure that the ceiling is strong enough to bear the weight of the unit. Before hanging the unit, test the
strength of each attached suspension bolt. It might be necessary to reinforce the ceiling frame to
prevent shaking. Consult an architect or carpenter for details
CAUTION
Ceiling
Body
10~12mm
L

2. INDOOR UNIT INSTALLATION
GB-8
2.4 INSTALL THE DRAIN PIPE
Remove the cover of the drain hose connection port
Insert the flexible hose to the drain hose port. Fix the flexible hose to the indoor unit with pipe clamp securely.
Install the flexible hose to the PVC water pipe (field supply, O.D.: Φ25) securely with PVC adhesive. Wrap the drain hose with
the insulation materials.
Pipe clamp
Indoor unit Flexible hose
Drain hose connection port
PVC water pipe (O.D.:Φ25)
PVC adhesive
2.4.1 Drainpipe connection
Cassette unit is eqipped with the drain pump
The drain pipe should be install within 200mm from the flexible hose and then install horizontal drainpipe with a slope of 1/00 or more
and fix it by hanger space of 1.0~1.5m.
The flexible hose should not be installed upward position; it may cause water flow back to the indoor unit.
Lean over 1/100
1.0-1.5m
Max. 750mm
Stow tube
<200mm
Drain hose connection port
2.4.2 Drainage test
Open the cover of water supply intake by turning and pulling the cover.
Gradually insert about 2 liters of water into the indoor unit with stow tube.
Operate the unit under COOLING mode and check a drain pump pumping (a time lag of 1 minute is allowed before water flowing
out depending on the length of the drain pipe).
Check and confirm the water flows out through the drain hose.
Check the drain water drops at the end of the drain pipe.
Make sure there is no water leak at the drainage
Reassemble the cover of water supply intake.
C
L
O
S
E
D
O
P
E
N
C
L
O
S
E
D
O
P
E
N
Cover
Drain pipe
connection port
Water intake
Cover

2. INDOOR UNIT INSTALLATION
2.5 INSTALL THE PANEL
7
GB-9
Before installation of the panel, be sure to remove the cushion for transportation between the fan and
orifice.
Install the panel according to below instructure after piping and wiring work has completed.
Joint the connecting sections of panel, ceiling surface and indoor unit closely. Any gap between them will
cause air leakage and this generate condensation or water leakage.
CAUTION
2.5.1 Push the two grille switches simultaneously, then lift the grille up and remove the air inlet grille.
Take out the installation covers from 4 corners.
2.5.2 Install the panel
Align corner marked with the piping side and drain side with piping interface and drainage interface of the main body.
Hang the panel to the hooks on the main body.
Tighten the screw evenly under the panel hook until the thickness of sponge between the main body and panel is reduced to
about 4~6mm, and the edge of panel should contack the ceiling well.
Connect the wire of swing motor to the corresponding splice on main body.
Grille switch
Piping port
Drain port
Hook panel
Screw
Cross-screwdriver
2.5.3 Install the air inlet grille
Hang the hook behind the air inlet grille on to the panel.
Connect the wire of display to the corresponding plug on main body.
Close the air inlet grille.
Press the installation cover gently into the panel.
Installation
cover’s rope
Tap Screw
Slide the four sliders
in the corresponding
channel when installing
the cover

GB-10
3. OUTDOOR UNIT INSTALLATION
3.1 INSTALLATION SITE CHOOSING
OUTDOOR UNIT
■ Where it is out of rain or direct sunlight.
■ Where it is well-ventilated and free from obstacles near the air inlet and air outlet.
■ Where does not increase the operating noise or vibration of the outdoor unit.
■ Where does not cause any drainage problem with discharged water.
■ Install the outdoor unit properly at a place that is durable enough to the weight of the outdoor unit.
■ Where provides appropriate clearances as outlined
■ Where the piping between the indoor and outdoor units is within the allowable limits.
■ In regions with snowfall and cold temperatures, avoid installing the outdoor unit in areas where it can be covered by
snow. If heavy snow is expected, a field supplied ice or stand and field supplied-installed wind baffle should be
installed to protect the unit from snow accumulation and blocked air intake.
■ When installing the outdoor unit in a place that is
constantly exposed to a strong wind, it is recommended
that a wind baffle be used.
X
O
Strong wind
3.2 OUTDOOR UNIT MOUNTING DIMENSION
W
H
mmmm
W
H
B
A
D
Outline dimension
845 700 320 335
WHD A B
945 810 395 405
938 1369 392 404
024
036
048/060
560
640
634
Model
(38QUS)

7GB-11
3. OUTDOOR UNIT INSTALLATION
3.3 SPACE REQUIREMENT FOR OUTDOOR UNIT
>30cm
>30cm
>200cm
>60cm
(Wall or obstacle)
Maintain channel
Air outlet
Air inlet
M
P
Air inlet
N
>60cm
Fix with bolt
Single Unit Installation
Before installation, check strength and horizontality of the base so that abnormal sound does not
generate.
Fix the base firmly with anchor bolts (M10) to prevent it from collapsing.
Install the foundation and vibration-proof rubbers to directly support the bottom surface of the fixing
leg that is in contact with the bottom plate of the outdoor unit.
3.4 INSTALL THE OUTDOOR UNIT
≥100mm
100～300mm
Outdoor unit
Vibration-proof rubber
Anchor bolt (M10)
Drainage (Wide 100mm x Depth 150mm)Mortar Hole (Φ100mm x Depth 150mm)
>200 >50 >300 >300 >30
>60
>200
>30
Parallel connect the two units or above Parallel connect the front with rear sides.
Connect the drain outlet with an extension drain hose
Fit the gasket onto drain outlet.
Insert the drain outlet into the base pan hole of outdoor unit, and rotate 90 degree to securely assemble them.
3.5 INSTALL THE DRAIN PIPE FOR OUTDOOR UNIT
unit:cm unit:cm
Base pan hole
of outdoor unit
Drain hose
(Field supply)
Gasket
Drain Outlet

4. REFRIGERANT PIPING WORK
GB-12
Check if the height difference between indoor unit & outdoor unit and the total length of refrigerant pipe
meet system requirement.
Refrigerant piping work follows the indoor unit and outdoor unit installation, connect the pipe at the indoor
side first, then the outdoor side.
Always keep ends of tubing sealed by placing a cap or covering with tape during installation and do NOT
remove them until you are ready to connect the piping.
Be sure to insulate any field piping all the way to the piping connection inside the unit. Any exposed piping
may cause condensation or burns if touched.
CAUTION
4.1 FLARING
NOTE
Tools required for flaring are pipe cutter, reamer, flaring
tool and pipe holder.
90
Oblique Rough Burr
Outside diameter
A(mm)
Max
8.7Φ6.35mm
Φ9.52mm
Φ12.7mm
Φ15.88mm
Φ19.05mm
12.4
15.8
19.0
23.3
8.3
12.0
15.4
18.6
22.9
Min
R0.4~0.8
45°±2
90°
±4
A
In case of needing brazing, work with Nitrogen gas blowing.
Improper torque will cause flare damage or gas leaks.
CAUTION
TorqueTubing size
18 ~ 20 N.m
25 ~ 26 N.m
35 ~ 36 N.m
45 ~ 47 N.m
65 ~ 67 N.m
Φ6.35mm
Φ9.52mm
Φ12.7mm
Φ15.88mm
Φ19.05mm
Use separate thermal insulation pipes for gas & liquid pipes.
The thickness above is a standard of the indoor temperature
of 27°C and humidity of 80%. If installing in an unfavorable
conditions such as near bathrooms, kitchens, and other similar
locations, reinforce the insulation.
Insulation’s heat-resistance temperature should be more than
120°C.
Use the adhesives on the connection part of insulation to
prevent moisture from entering.
Repair and cover any possible cracks in the insulation specially
check the bent part or hanger of pipe.
4.1.1 Using a pipe cutter to cut the pipe to the requested
length. Ensure that the cut edge remains at 90° with
the side of the pipe.
4.1.2 Use a reamer to remove burrs with the cut surface
downward so that the chips do not enter the pipe.
4.1.3 Carry out flaring work using flaring tools as below.
4.1.4 Check if the flaring is properly made. See incorrectly
flared pipes sample below.
4.2 PIPING WORK
4.2.1 Align the center to tighten the flare nut and finish
connection using two wrenches.
Flare nut
Wrench
Torque wrench
4.2.2 Select the appropriate insulation material for refrigerant
pipe. (Min. 10mm, thermal insulating foam C)
Inclined Damaged Surface Cracked Uneven Thickness

4. REFRIGERANT PIPING WORK
7
GB-13
After the piping work is finished, make sure to check the connection part of each refrigerant pipe and confirm that there is no gas leak by
applying soapy water to them or by using a leak detector specific for HFC refrigerants. Refer below picture for illustration.
A: Low pressure stop valve B: High pressure stop valve
C& D: Indoor unit flare nuts
Check-point of indoor unit
Check-point of outdoor unit
A
BC
D
4.3 REFRIGERANT PIPE
Gas Side
Model
Φ15.88mm
Liquid Side Allowable
pipe length (m) Max. Height difference (m) Charge less length (m) Additional charge per meter (R410A)
38QUS060
38QUS024
38QUS036/48 Φ9.52mm
Φ9.52mm
Φ9.52mm
Φ15.88mm
Φ15.88mm
5
5
5
25
30
30 20
15
10 30 g/m
30 g/m
30 g/m
NOTE
When the pipe length is over 5m, the additional refrigerant should be added according to the piping length.
4.4 AIR EVACUATION
Connect the charge hose from the manifold gauge to the service port of the gas side packed valve.
Connect the charge hose to the port of the vacuum pump.
Fully open the handle Lo of manifold gauge.
Operate the vacuum pump to evacuate air from the system until 76cmHg.
Close the handle Lo of manifold gauge.
Fully open the valve stem of the packed valves.
Remove the charging hose form the service port.
Securely tighten caps of packed valve.
-76 cmHg
Handle Lo Handle Hi
Charge hose Charge hose
Vacuum pump
Packed valve
Manifold valve
Compound gauge Pressure meter
4.5 LEAKAGE TEST

5. WIRING
GB-14
Power supply and connecting wires specification
Model QUS024
H07RN-F; 3×2.5mm2 Power Cord(Field Supply)
Indoor/outdoor connecting wiring
(Field Supply)
Power
Supply
Phase 1-Phase
220-240V~ 50Hz
Frequency and volt
Rated Current
Fuse Rating(Field Supply)
5.1 POWER FROM OUTDOOR SIDE (For QUS024)
There are two kinds of wire connection. Check the wiring diagram carefully before connect the wire.
Wiring figure
H07RN-F; 4×2.5mm2
13.0A
20A
All the electrical connections must be carried out by qualified installers and all the wirings must be
connected according to the wiring diagram.
Make ground connection prior to any other electrical connections.
All power sources must be turned off before wiring work and do not turn on the power until you have
made sure all the wirings have been safety checked.
A main switch and circuit breaker or fuse must be installed, the capacity should be above 1.5 times of
maximum current in circuit.
An individual branch circuit and single socket used only for this appliance must be available.
Wire cross section is depending on the rated current and national, state and local electrical wiring
code. Consult local building codes and National electrical code for special requirement.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
The unit must be connected to the main power supply by means of a circuit breaker or a switch with a
contact separation of at least 3mm in all poles. Installation of a residual current device (RCD) having
a rated residual operating current not exceeding 30mA is advisable.
CAUTION
Ground wiring
Ground wiring
Power supply
Switch/Fuse
Power Cord
High voltage wiring (Power supply)
Signal line
Indoor
Unit
Outdoor
Unit

7
GB-15
Connection Diagram
5. WIRING
5.2 INDEPENDENCE POWER SUPPLY (For QUS036~060)
Ground wiring
Ground wiring
Power supply
Switch/Fuse
Power Cord
Signal line (Low voltage)
Indoor
Unit
Outdoor
Unit
Wiring figure
Power supply
Switch/Fuse
Power Cord
Power supply and connecting wires specification
Outdoor Unit (QUS024)
60mm
40mm10mm
Power input cord
GND
Connective Cable
Model QUS036
H05VV-F; 3×1.0mm2
Power Cord(Field Supply)
Indoor/outdoor connecting wiring
(Field Supply)
Indoor
Phase 1-Phase
220-240V~ 50Hz
Frequency and volt
1.8A
Rated Current
Fuse Rating(Field Supply) 16A
Shielded cable; 2×0.2mm2
QUS048
H05VV-F; 3×1.0mm2
1-Phase
220-240V~ 50Hz
1.2A
16A
QUS060
H05VV-F; 3×1.0mm2
1-Phase
220-240V~ 50Hz
1.2A
16A
H07RN-F; 3×4.0mm2
Power Cord(Field Supply)
Outdoor
Phase 1-Phase
220-240V~ 50Hz
Frequency and volt
21.0A
Rated Current
Circuit Breaker(Field Supply)
40A
H07RN-F; 5×2.5mm2
3-Phase
380-420V 3N~ 50Hz
13.0A
30A
H07RN-F; 5×2.5mm2
3-Phase
380-420V 3N~ 50Hz
13.0A
30A
Shielded cable; 2×0.2mm2
Shielded cable; 2×0.2mm
2
60mm
40mm10mm
GND
1(L) 2(N) SL N
Power Input
To Indoor
To Outdoor
1(L) 2(N) S
Indoor Unit (QTD024)

GB-16
Connection Diagram
5. WIRING
Separate the low voltage wiring (signal wire) and high voltage wiring (power supply wiring) at least 0.5m so that they do not
pass through the same place together. Proximity may cause electrical interference, malfunctions, and breakage.
CAUTION
60mm
40mm10mm
Power input cord
(Single phase)
GND
60mm
40mm10mm
GND
LNS1 S2
Outdoor Unit (QUS036)
Power Input To Indoor
L1 N S1 S2 L2 L3
Outdoor Unit (QUS048~060)
Power Input To Indoor
Power input cord
(Three phase)
Indoor Unit (QTD036~060)
LNS1 S2
Power Input To Outdoor

6. FINAL CHECK AND TRAIL OPERATION
To complete the installation, perform the following checks before the trial operation.
Strength of the installation site for both indoor and outdoor sides, confirm no obstruction of the unit air outlet or return.
Tightness of Refrigerant piping connection and confirm no leakage
Electric wiring connections are correctly completed and unit has been grounding connected
Check the total length of the piping and record the volume of the additional charged refrigerant
The power supply should complying with the rated voltage of the air conditioner
Insulation of the pipe
Drainage
6.1 FINAL CHECK LIST
Set the air conditioning under the COOLING mode with the remote controller (or manual button) and check the running status of both
indoor unit and outdoor unit. In case of any malfunction, resolve it according to chapter “Trouble shooting” in the “Service Manual”.
Indoor unit
Whether the buttons (such as ON/OFF, MODE, TEMPERATURE, FAN SPEED etc.) on the remote controller work well.
Whether the louver moves normally.
Whether the room temperature is adjusted well.
Whether the indicator lights on the display panel are normal.
Whether the “manual” button works well.
Whether the drainage is normal.
Whether there is a vibration or abnormal noise during the operation.
Whether the indoor unit works well in COOLING or HEATING mode.
Outdoor unit
Whether there is a vibration or abnormal noise during the operation.
Whether the wind, noise or condensed generated by the air conditioner have disturb your neighborhood.
Whether there is any refrigerant leakage.
6.3 TRAIL OPERATION
When restart the unit, there will be approximately 3 minutes delay to run for protection.
CAUTION
6.2 MANUAL OPERATION
Manual operation can be accessed by pressing manual button on display panel.
Press the manual button repeatedly to change modes as follows:
Once = AUTO mode [heat, cool or fan, 24
°C and auto fan speed .
Twice = COOLING mode [switch to AUTO mode after 30 minutes (mainly used for trial operation)]
Three times = OFF
GB-17

BEIJER RET AB
Stortorget 8
Malmö
Sweden