Carson Preference Series User manual

Please read this manual before installing and using the
projection screen. Retain this manual for future reference.
Preference
Instruction manual for Preference One,
Preference Acoustic, Preference Black

Items listed here may change without prior notice.
The company reserves the right to all of the listed items.
Screen (1pc)
Remote control (1pc)
Ceiling mount brackets (2 pcs)
Removable wall mount brackets (2 pcs) (150” 4 pcs)
Hanging Safety clasp (2 pcs) (150” 4 pcs)
Hanging loop (2 pcs) (150” 4 pcs)
Vertical hook (2 pcs) (only for size less than 135”)
5X40Tapping screw (4 pcs) (150” 4 pcs)
Expanded colloidal particles (8 pcs) (150” 4 pcs)
Concrete anchor (4 pcs) (150” 8 pcs)
Hexagon nuts (2 pcs) (150” 4 pcs)
Hexagon regulating bar (1 pc)
IR Remote receiver cable (1 pc)

Important Safety Tips
 WARNING: Incorrect installation and improper use may lead to mechanical
failure or personal injury.
Considerations for installing / using this product
1. Handle with care to avoid damage.
2. Do not expose the product to rainwater or any other form of moisture.
3. Keep away from heat sources, such as radiators and other items that may
emit heat
4. Do not attempt to remove the fuselage shell and private wiring by Yourself.
5. Check whether the voltage is consistent with the required voltage.
6. Avoid scratching or folding the screen surface.
7. Put the screen back into the shell to after use to protect it from dust
pollution.
8. Do not open and close the screen frequently in a short period of time.
9. Keep the screen horizontal at all times.
The company will not be liable for any damages or injuries caused by a faulty
installation or operation.
 Do not adjust the limit by yourself
Cleaning
Use a soft, dry cloth with non-corrosive components and neutral soap water to
gently clean the screen and the shell. DO NOT USE chemicals or corrosive
materials to avoid damaging the product.

Wall mount
Wooden wall mounting method
Concrete/ brick wall mounting method

1
Install the back buckle brackets
horizontally on the wall with either
concrete anchor or expansion glue and
self-tapping screw – depending upon
the nature of the surface.

2
Align the back of the screen with
the hooks on the wall mounting
brackets, then slowly lower the
screen down onto the wall
brackets.

3
Once the screen is mounted,
tighten the safety screws as
shown in then photos.

4
Once installation is complete, it
should look like the photo below.
To demount the screen, follow
the steps in reverse.

Ceiling mount
Wooden ceiling mounting method
Concrete ceiling mounting method

1
Remove screen from the package.
Unscrew the side caps from both sides,
and slide the ceiling mount bracket on.
Screw the side cap back on.

2
Install the ceiling mount brackets
vertically with either concrete
anchor or wooden supports
depending on the nature of the
surface being installed on.

1
Ceiling hanging mount
Pass the ceiling mount brackets
thorugh the hanging loop, then
x it with screws.

2
Ax vertical hooks on the
ceiling, ensuring they are level

3
Clip the safety buckle and hanging
loop together, then hang the screen
directly on the vertical hooks. 2 people
must be doing the lifting of the screen.
If it is a high ceiling, use a metal or steel
chain to connect the vertical hooks to
the safety buckle directly as shown in
last gure.
Complete view

Electric screens can be operated in
following two ways:
Up
Down
Manual Control
Down”↓screen opens; “Stop”→Screen
stops; “Up”↑Screen closes.
The IR Remote receiver cable needs to
be connected for the remote to operate
Usage

Up
Down
Stop
Remote Control
Built-in RF remote control/external RF
remote control/IR control optional
Press the “UP” button for 3 seconds and
plug in the receiver.
Once the receiver buzzer rings, STOP
pressing the “UP” button. Pairing mode
is now active.
Press the “UP” button once and release
When the buzzer rings 3 times in a row,
the remote pairing function is
complete
Pairing the remote control

Nature of fault
Screen not fully closing
Probable cause Solution
Low battery in remote Replace battery
Power cable not
connected
Motor in thermal
protection mode after
extended period of use
Adjust the height of the
screen
Let motor cool for 15
minutes, then retry
Refer to the user
manual or contact the
factory. DO NOT
attempt to fix yourself
Connect the power
cable
Screen does not go
up or down, non
responsive
Troubleshooting
Nature of fault
Remote control is not
responsive
The remote control and
receiver work well, but
the motor doesn't run
Likely incorrect wiring
of the motor
Correct the wiring
according to
instructions
Remote control battery
is dead
Get a new battery
Probable cause Solution
- Receiver wiring likely
incorrect;
- Code pairing likely
incomplete
- Correct the wiring
according to
instructions
- Correct code matching
between remote and
receiver
The indicator on the
remote is on but the
receiver is
unresponsive
Screen
Remote

[email protected]
carsonscreens.com.au