Carving Fitness Balance User manual

www.carvingfitness.com
CARVING BALANCE INSTALLATION GUIDE
Tools Needed
Hex key 8mm
Hex key 7mm
Hex key 4mm
Hex key 3mm
17mm Wrench
Blanket for floor protection
________________________________________________________________________________
Installation hardware kit
14x (M10 x 25mm) Hex Bolt Stainless Steel
22x (M10 x 20mm) Hex Bolt
4x (M5 x 20mm) Hex Deep set Screw
5x (M5 x 10mm) Hex Bolt
2x Leveler for under Base Frame
1x Power Adapter kit (EU plug)
Hardware arts

www.carvingfitness.com

www.carvingfitness.com
Use a blancket to protect both the floor and the Carving Balance Unit.
Put Frame connector cable into frame hole like indicated
with the red arrow
Flip Base Frame and let it rest on its upper side to connect
the Stabilizer Legs to the Base Frame with 18x (M10 x
20mm) Hex Bolt. Use a 8m Hex key. See pictures below
for reference.

www.carvingfitness.com
Install the Stabilizer Connection Bar with 4x
(M10 x 20mm) Hex Bolt. Use a 8m Hex key
Install the 2x Levelers in the Base Frame like
shown. If needed use a 17mm Wrench
Flip the Base Frame with the Stabilizers mounted back on its bottom side
Connect the 2 Pedals to the Pedal Connection
Bars with 5x (M10 x 25mm) Stainless Steel bolts,
per pedal.
Use a 7mm Hex Key
Place the Bottom Frame Cover on the Base
Frame like shown in the picture with 2x (M5 x
10mm) bolts..
It’s located underneath the Pedals on the frame.
Use a 4mm Hex Key

www.carvingfitness.com
Carefully place the Main Cover over the Base
Frame like shown in the picture.
Place the 3x (M5 x 10mm) bolts on the position
like indicated in the picture.
Use a 4mm Hex Key
Place the Top Cover on the Base Frame and
Main cover
Mount theTop Cover with 4x (M5 x 20mm)
Hex Deep set screw
Use a 3mm Hex Key

www.carvingfitness.com
The following Ste requires 2
ersons!!!
First person take
s
the Upright
Assembly and carefully holds this
above the Base unit.
The 2
nd
person connects the Frame
Cable to the Upright Cable like shown
in the picture.
Once connected, slide the cable
connectors upwards inside the Upright
Assembly like indicated with the Red
Arrow in the picture.
Carefully lower the Upright Assy to the
Base Frame.
One person holds the Upright Assy in
position
Warning: The substantial weight of the
Upright Assy can damage the Top
Cover with its sharp edges when this is
not done with Care!!!
Take the remaining 4x (M10 x 25mm)
Stainless Steel bolts .
Use a 7mm Hex Key to firmly but carefully
tighten these bolts which connect the
Upright Assy to the Base Frame Unit.

www.carvingfitness.com
Install the Power Adapter kit. The entry of the plug is on the left
side underneath the Carving Balance unit (bottom side of the
frame)
Use for exam
ple a wooden blo
ck to put
underneath the left leveler.
This creates more space between the
frame and the floor.
Plug the adapter cable inside the frame.
The Adapter jack is close to the left
leveler.
Life the Carving Balance unit and remove
the wooden block.
Once in its desired position:
Stabilize the Carving Balance unit with the
2 levelers which are underneath the
frame.
Once stabile and level, do not forget to
tighten the Locking nuts of the levelers to
the frame.
Warning: When the lock nuts are not
tightened, the unit will slide when in
use and will create noise!!
We wish you a fun and rewarding
training with your Carving Balance

www.carvingfitness.com