
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: sale@carymart.com
Press button A again: Terminal OUT1 stops outputting.
Press button B of the transmitter: Terminal OUT2 outputs DC power.
Press button B again: Terminal OUT2 stops outputting.
Press button C of the transmitter: Terminal OUT3 outputs DC power.
Press button C again: Terminal OUT3 stops outputting.
Press button D of the transmitter: Terminal OUT4 outputs DC power.
Press button D again: Terminal OUT4 stops outputting.
Setting control mode Momentary, Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button A of the transmitter: Terminal OUT1 outputs DC power.
Release buttonA of the transmitter: Terminal OUT1 stops outputting.
Press and hold button B of the transmitter: Terminal OUT2 outputs DC power.
Release button B of the transmitter: Terminal OUT2 stops outputting.
Press and hold button C of the transmitter: Terminal OUT3 outputs DC power.
Release button C of the transmitter: Terminal OUT3 stops outputting.
Press and hold button D of the transmitter: Terminal OUT4 outputs DC power.
Release button D of the transmitter: Terminal OUT4 stops outputting
Setting control mode Latched, Do not connect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press buttonA of the transmitter: Terminals OUT1 output DC power, and other terminals OUT2, OUT3, OUT4 no output.
Press button B of the transmitter: Terminals OUT2 output DC power, and other terminals OUT1, OUT3, OUT4 no output.
Press button C of the transmitter: Terminals OUT3 output DC power, and other terminals OUT1, OUT2, OUT4 no output.
Press button D of the transmitter: Terminals OUT4 output DC power, and other terminals OUT1, OUT2, OUT3 no output.
Setting control mode Momentary + Toggle, Connect Jumper-1 and Jumper-2:
Control mode Momentary (Channel A, B): Press and hold -> On; Release -> Off.
Press and hold button A of the transmitter: Terminal OUT1 outputs DC power.
Release buttonA of the transmitter: Terminal OUT1 stops outputting.
Press and hold button B of the transmitter: Terminal OUT2 outputs DC power.
Release button B of the transmitter: Terminal OUT2 stops outputting.
Control mode Toggle (Channel C, D): Press -> On; Press again -> Off.
Press button C of the transmitter: Terminal OUT1 outputs DC power.
Press button C again: Terminal OUT1 stops outputting.
Press button D of the transmitter: Terminal OUT2 outputs DC power.
Press button D again: Terminal OUT2 stops outputting.
Input control terminals:
The receiver has four input control terminals, you can connect external devices, sensors, or manual switches to these terminals to control the outputs
of receiver.
1) Signal input:
You can connect external devices (with low level output signal) to terminals “COM”, “Signal 1”, “Signal 2”, “Signal 3”, “Signal 4”, the external device’s
output signal can control receiver’s four outputs.
When the external device outputs low level signal to terminal “COM”and “Signal 1“, Terminal OUT1 outputs DC power.
When the external device outputs low level signal to terminal “COM”and “Signal 2“, Terminal OUT2 outputs DC power.
When the external device outputs low level signal to terminal “COM”and “Signal 3“, Terminal OUT3 outputs DC power.
When the external device outputs low level signal to terminal “COM”and “Signal 4“, Terminal OUT4 outputs DC power.
2) The manual switches:
You can connect four manual switches to terminals “COM”, “Signal 1”, “Signal 2”, “Signal 3”, “Signal 4”, then you can use these manual switches to
control the outputs of receiver.
When connect terminals “Signal 1”and “Com”, Terminals OUT1 outputs DC power. And when disconnect “Signal 1”and “Com”, Terminal OUT1 stops
outputting.
When connect terminals “Signal 2”and “Com”, Terminals OUT2 outputs DC power. And when disconnect “Signal 2”and “Com”, Terminal OUT2 stops
outputting.
When connect terminals “Signal 3”and “Com”, Terminals OUT3 outputs DC power. And when disconnect “Signal 3”and “Com”, Terminal OUT3 stops
outputting.
When connect terminals “Signal 4”and “Com”, Terminals OUT4 outputs DC power. And when disconnect “Signal 4”and “Com”, Terminal OUT4 stops
outputting.
How to pair the transmitter to the receiver:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on transmitter, if signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.