CaryMart S1PU-AC-ANT3 User manual

SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
Water Tank Water Level Wireless Automatic Remote Control System
Package Include:
1 x Receiver: S1PU-AC-ANT3
1 x Transmitter: CB-2
1 x Transmitter: CB-2N-2
2 x Water Level Sensors
1 x User manual
Working Principle:
Transmitter CB-2N-2 is a special remote control with normally open contact trigger. It has 3 input wires for connecting two devices with normally
open contact, such as warning host, cable detectors, various sensors, limit switches, Programmable Logic Controllers and so on.
This transmitter can be combined with different types of receivers to form a wireless control system, and this system is used to wirelessly control the
device A through the device B with normally open contact.
Application:
You can connect two water level sensors to this transmitter, and connect the water pump to the receiver, then the pump will automatically work
according to the water level.
When the water reaches the low water level, the water level sensor 1 is triggered, the transmitter automatically emits a wireless signal "ON". When
the receiver receives this wireless signal, it will turn on the pump motor to pump water into the tank.
When the water reaches the high water level, the water level sensor 2 is triggered, the transmitter automatically emits a wireless signal "OFF".
When the receiver receives this wireless signal, it will turn off the pump motor to stop pumping water.
Feature:
Wireless control, easy to install
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
Automatic control AC110~240V water pump motors by two water level sensors.
Universal input: Support 110V AC (100V~120V) used in US, Canada, etc, and 220V AC (200V~240V) used in Germany, UK, France, etc.
Relay Output: This receiver is dry relay output, it can be used to operate both DC and AC equipments. The output terminals are NO / NC (normally
open / normally closed), which serves as a switch. That means you should also connect a separate power supply to equipments.
High Power: Maximum load current 30A.
With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
With external telescopic antenna, the receiver have a farther working range.
You can control the pump by the receiver with the transmitter from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
Reliable control: The code has thousands of different combinations, and the receiver only works with the transmitter which use the same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.
Receiver:
Model No.: S1PU-AC-ANT3
Power Supply (Operating Voltage): AC100~240V (110V/120V/220V/240V)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Wire range for the terminals: 22-12 AWG
Working Frequency: 315MHz
Channel: 1CH
Control Modes: Interlocking
Quiescent Current: ≤6mA
Maximum Load Current: 30A
Operating Temperature: -20°C to +70°C
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Transmitters:
Model No.: CB-2
Channel / Button: 2
Button Symbol: A, B
Operating Voltage: 9V (1 x 6F22 -9V battery, can be used for 12 months)
Working Current: 30mA
Operating Frequency: 315MHz
Modulation Mode: ASK
Transmitting Distance: 1000m / 3000ft (theoretically)
With power switch on the side.
Operating Temperature: -20°C to +70°C
Unit size: 135mm x 42mm x 25mm
Model No.: CB-2N-2
With External Trigger Wires.

SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
Triggering method: When wire 1 and wire 3 are connected, it will send wireless signal "ON". When wire 2 and wire 3 are connected, it will send
wireless signal "OFF".
Channel / Button: 2
Button Symbol: A, B
Operating Voltage: 9V (1 x 6F22-9V battery, can be used for a week; or 1 x 9V Rechargeable Lithium Battery, can be used for two weeks. If you
want a longer working time, please use a 9V power adapter, or use our solar power supply system.)
Working Current: 30mA
Operating Frequency: 315MHz
Modulation Mode: ASK
Transmitting Distance: 1000m / 3000ft (theoretically)
With waterproof case and external antenna.
With power switch on the side.
Operating Temperature: -20°C to +70°C
Unit Size: 135mm x 42mm x 25mm
Water Level Sensor:
Body Material: PP
Float Material: PP
Operating Temperature: -10°C to +85°C
Maximum Voltage: DC 100V
Maximum Current: 0.5A
Maximum Power: 10W
Working Range:
The maximum working distance can reach 1000M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it
will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach
this maximum working distance.
Usage:
1. Installation:
1) Put the water level sensor 1 downwards and install at the low water level position in the tank; Put the water level sensor 2 upwards and install at
the high water level position in the tank.
2) Connect the water level sensor 1 to wire 1 and wire 3 of transmitter CB-2N-2.
3) Connect the water level sensor 2 to wire 2 and wire 3 of transmitter CB-2N-2.
4) Connect the live wire of AC power supply to the receiver's terminal "L / +", and connect the neutral wire of AC power supply to the receiver's
terminal "N / -".
5) Connect the live wire of AC power supply to the receiver's terminal B, connect one side of the pump to the terminal C, and connect another side
of the pump to the neutral wire of AC power supply.
2. Operation:
1) Control pump by transmitter CB-2:
Press button A of the transmitter CB-2, the relay of receiver is activated, and the pump is turned on.
Press button B of the transmitter CB-2, the relay of receiver is deactivated, and the pump is turned off.
2) Automatically control pump by transmitter CB-2N-2 & Water Level Sensors:
When the water reaches the low water level, two wires of the water level sensor 1 is connected, the transmitter CB-2N-2 automatically emits a
wireless signal "ON", which is equivalent to the function of the button A on the transmitter. When the receiver receives this wireless signal, it will turn
on the pump motor to pump water into the tank.
When the water reaches the high water level, two wires of the water level sensor 2 is connected, the transmitter CB-2N-2 automatically emits a
wireless signal "OFF", which is equivalent to the function of the button B on the transmitter. When the receiver receives this wireless signal, it will
turn off the pump motor to stop pumping water.
You also can press button A or button B on the transmitter to turn on / off the pump.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver; signal LED on the receiver is turned on, it means the receiver enters the learning status.
2) Press any one button on transmitter, if signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the learning status, press again the learning button, if signal LED turns off, it means learning process was discontinued.
4) The receiver can learn several transmitters with different codes.
Delete all transmitters:
We have learned transmitter to the receiver. If you don’t want the receiver to work with the transmitter, you can delete all codes of transmitters,
which are stored in the receiver.
Operation: Press and hold the learning button of receiver until signal LED flashes slowly, then release the button, signal LED remains flashing
slowly, it means all stored codes have been deleted successfully.

SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
Application: For AC water pump motor