Casio DT-X10M10E User manual

DT-X10 Series
Laser Scanner Integrated Models
Hardware Manual
(Version 1.01)
CASIO Computer Co., Ltd.
Copyright ©2005. All rights reserved.
August 2005

2
Table of Contents
Editorial Record 4
Preface 5
Chapter 1 Overview 6
1.1 Features 6
1.2 Available Models And Options 7
1.2.1 Options And Interfaces 9
1.3 General Guide 10
1.3.1 DT-167CHGE (Car Mounted Battery Charger) 12
1.3.2 DT-160IOE (Bridge Satellite Cradle) 13
1.3.3 DT-5022CHG (Rapid Battery Charger) 15
1.3.4 DT-5023BAT/DT-5025LBAT (Battery Packs) 16
Chapter 2 Hardware Specifications 17
2.1 DT-X10 17
2.2 DT-160IOE (Bridge Satellite Cradle) 19
2.3 DT-167CHGE (Car Mounted Battery Charger) 20
2.4 DT-169CHGE (Cradle-type Battery Charger) 21
2.5 DIP Switch Setting (For DT-160IOE) 22
2.6 Status Indication With LEDs 23
2.7 DT-5022CHG (Rapid Battery Charger) 23
2.8 DT-5023BAT/DT-5025LBAT 25
2.9 DT-894CFU (CF Card Extension Unit) 25
Chapter 3 Interfaces 26
3.1 DT-X10 26
Chapter 4 Product Identification And Reference Numbers 28
Chapter 5 Quality References 29
5.1 Environment Performances 29
5.1.1 DT-X10 29
5.1.2 DT-160IOE/DT-169CHGE 29
5.1.3 DT-167CHGE 30
5.1.4 DT-5022CHG 30
5.1.5 DT-5023BAT/DT-5025LBAT 30
5.1.6 DT-894CFU 31
5.2 Electrical Performances 32
5.2.1 DT-X10 32
5.2.2 DT-160IOE/DT-169CHGE 32
5.2.3 DT-167CHGE 32
5.2.4 DT-5022CHG 33
5.2.5 DT-5023BAT/DT-5025LBAT 33
5.2.6 DT-894CFU (CF Card Extension Unit) 33
5.3 Mechanical Performances 34
5.3.1 DT-X10 34
5.3.2 DT-160IOE/DT-169CHGE 34
5.3.3 DT-5022CHG 34
5.3.4 DT-5023BAT/DT-5025LBAT 35
5.3.5 DT-894CFU(CF Card Extension Unit) 35
5.4 Reliability 36
5.4.1 DT-X10 36
5.4.2 DT-160IOE/DT-169CHGE 36
5.4.3 DT-5022CHG 36
5.5 Compliance 37
5.5.1 DT-X10 37
5.5.2 DT-160IOE/DT-169CHGE 37

3
Chapter 6 Cable Specifications 38
6.1 For Chain Connection And Short Length 38
6.2 For Chain Connection And Long Length 39
Chapter 7 Precautions 40
7.1 Handling Precautions 40
7.2 Safety 41
7.2.1 Battery Pack 41
7.2.2 General 42
CASIO is a registered trademark of CASIO Computer Co., Ltd. in Japan.
Other product names or company names in this reference manual are either trademarks or registered trademarks of
their respective owners.
No part of this document may be produced or transmitted in any form or by any means, electronic or mechanical,
for any purpose, without the express written permission of CASIO Computer Co., Ltd. in Tokyo Japan.
Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no
representations or warranties with respect to the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any particular purpose.
© 2005 CASIO Computer Co., Ltd. All rights reserved.

4
Editorial Record
Manual
Version
no.
Date edited Page Content
1.00 November 2003 Original version
1.01 August 2005 All The description about new model, DT-X10M10RC2, is added.

5
Preface
This reference manual describes about the CASIO DT-X10 series handheld terminals with Laser Scanner
integrated only. For the models with C-MOS imager integrated, refer to the “DT-X10 Series Hardware Manual”.
A new generation of handheld terminal has been developed. CASIO has developed the revolutionary
DT-X10M10E, DT-X10M10RC and DT-X10M10RC2 handheld terminals with built-in Intel PXA255
Application Processor, 1D bar code scan engine and diverse Wireless LAN communications via Bluetooth,
IEEE802.11b Wireless LAN and WAN card (GSM, GPRS, CDMA, etc.). Running under Microsoft Windows
CE .NET4.1 operating system, the rugged DT-X10M10E, DT-X10M10RC and DT-X10M10RC2 are designed
specifically with the transportation market in mind.
In this reference manual, the models are described as “DT-X10” or “the terminal” or “handheld terminal”.

6
1. Overview
1.1 Features
Incorporates .NET technology
•Uses WindowsCE .NET 4.1 operating system.
•Makes effective use of .NET resources developed by other corporations.
•Employment of Embedded OS makes it possible to build a flexible WindowsCE system.
Enhanced communicating functions
•Covers GPRS/Wireless LAN, etc. by using various communication cards.
•Built in Bluetooth Ver1.1 module.
•The transfer rate of the Wireless LAN is 5 Mbps, which is the maximum rate of communication for
peer-to-peer connection with PC over IEEE 802.11b.
•The following protocol stacks are available for Bluetooth interface:
GAP (Generic Access), SDP (Service Discovery), SPS (Serial Port), Dialup Network, File Transfer.
•Security function (WEP 128 bits)
Superb scanning capability
•With the installed bar code scan engine it is possible to read industrial standard bar codes.
•Scanning performance is comparable to the CASIO IT-500 series handheld terminal.
•Multi-step bar code read function.
Support of outstanding development environment
Ample Microsoft development tools provided for easy application development and an advanced debug
environment.
High expandability
The standard PCMCIA slot makes it possible to use various standard peripheral cards.
Aiming to a full compliance with the “Restriction of the use of certain
Hazardous Substances in electronic equipment (RoHS)” set mandatory on July
1 2006
The following product has been assembled with devices, components and parts manufactured using Lead (Pb)
free solder.
•DT-X10M10RC2

7
1.2 Available Models And Options
Table 1.1 List of models
Wireless LAN Memory
Model IEEE802.11b Bluetooth Scan Engine RAM FROM
DT-X10M10E No Yes Yes 32 MB 64 MB
DT-X10M10RC * ETSI Yes Yes 32 MB 64 MB
DT-X10M10RC2 ** ETSI Yes Yes 32 MB 64 MB
Notes:
Bluetooth: Bluetooth Version 1.1 module is integrated as standard
* ETSI : Wireless LAN (IEEE802.11b) module, no. WCF201BERWP100, produced by INTEL
Corporation which is compliant with the ETSI standard is integrated.
** ETSI : Wireless LAN (IEEE802.11b) module, no. 6180120, produced by Toyota Industries Corporation
which is compliant with the ETSI standard is integrated.
Table 1.2 Options
Model Product Remark
DT-160IOE Bridge Satellite Cradle
DT-169CHGE Cradle-type Battery Charger
DT-891WH Wall Mount Unit
DT-167CHGE Car Mounted Battery Charger
DT-827CAC Car Power Cable Not marketable in the USA/Canada
DT-5022CHG Dual Battery Charger
MPC-577ADP AC Adaptor Output; 16DCV, 2.8 A AC100V to AC230V
AD-S42120AE AC Adaptor Output; 12DCV, 3.0 A AC100V to AC230V
DT-5023BAT Battery Pack Lithium-ion rechargeable battery 1,550 mAh
DT-5025LBAT Large-capacity battery Pack Lithium-ion rechargeable battery 3,400 mAh
DT-894CFU CF Card Extension Unit CF Type I/ Type II The large-size card cover comes
as standard
DT-893LTCV Communication Card Cover For large-size card
DT-892TCV Communication Card Cover
DT-887AXA RS-232C cable Length; 1.5 m, 9-pin female
DT-882RSC RS-232C cable 25-pin male
DT-883RSC RS-232C cable 25-pin female
DT-380USB USB cable Length; 2.0 m
DT-888RSC RS-422 cable Length; 1.0 m
SB-201 USB cable Length; 2.0 m Between DT-X10 and PC
FX-DS110-APL Access-Point manufactured by
Contec
See note 1 below.
AP-1000 Access-Point manufactured by
ORiNOCO
See note 2 below.
Notes:
1. The Access-Point is a product of Contec Co., Ltd... It will be distributed by the worldwide sales network of
Contec Co., Ltd.
2. The Access-Point is a product of Agere Systems in the USA. It will be distributed by the worldwide sales
network of Agere Systems.

8
The accessories in the table below are accompanied in each individual carton box of the models.
Table 1.3 Accessory
Product Q’ty Remark
Large-capacity Battery Pack Cover 1 For DT-5025LBAT
PC Card Remover 2
Stylus 1
Wrist strap 1
User’s Guide 1 in English and Chinese (simplified characters)

9
1.2.1 Options And Interfaces
USB
(Ver1.1 Function)
PC
IrDA port
(IrDA 1.0) Bridge Satellite Cradle
DT-160IOE
Power supply
(Built-in charger)
Car mounted battery
charger
DT-167CHGE
Dual battery
charger
DT5022CHG
PC
USB
RS-232C
USB
ｶｰﾄﾞDoPA
ｶｰﾄﾞGPRS
Battery pack
DT-5023BAT
Large-capacity
battery pack
DT-5025LBAT
Memory card
WAN card,
etc.
Memory card,
RF card, etc.
Access-Point
Label printer, etc.
PCMCIA
Bluetooth module
(Ver1.1 Class2) Label printer,
etc.
Communication card
cover
DT-892TCV
DT-893LTCV
DT-X10
CF card extension unit
DT-894CFU
AC adaptor
AD-S42120AE
Car Power cable
DT-827CAC
Cradle-type battery
charger
DT-169CHGE
AC adaptor
AD-S42120AE
Dual battery
charger
DT5022CHG AC adaptor
MPC-577ADP
Battery pack
DT-5023BAT
Large-capacity
battery pack
DT-5025LBAT
Bridge Satellite
Cradle
DT-160IOE
RS-422 RS-422
AC adaptor
AD-S42120AE
Non-
Wireless
LAN model
Wirelss LAN
model
Wireless LAN
CF expansion I/F
Fig. 1.1

10
1.3 General Guide
Views
Table 1.4 Names of parts
No. Name Description
Indicates the result of a bar code read operation.
Red : Read error
1 Indicator 1
Green : Read successfully
Indicates the charge status of the battery pack.
Red : Charging
2 Indicator 2
Green : Charging complete
3 LCD panel and touch
screen
Shows text, operation indicators, etc. Also, operations can be performed and
text can be input using the supplied stylus.
4 Buzzer Sounds a buzzer.
5 Power key Hold down for about one second to turn the power on or off.
6 Cursor keys These keys operate much like a computer’s cursor keys. They can be used to
select items, scroll screen contents, etc.
7 Programmable key This key can be assigned with any function available.
8 Numeric keys Use these keys to input numbers and letters.
9 Execute key Press to register an input value and advance to the next step.
These keys can be assigned any function other than bar code reading. The
following are initial default settings.
F1 : Deletes one character to the left.
F2 : Inputs a hyphen (-).
F3 : Inputs a period (.).
10 Function keys
F4 : Toggles to switch between numbers and alphabets.
11 IR port This port is used for IR data communication with another Handheld Terminal
or the Bridge Satellite Cradle.
12 Power contacts Contact points for supplying power from the Bridge Satellite Cradle and
Cradle-type Battery Charger.
13 CLR key Press to clear all key inputs.
14 Fn key Press this key and then a function key or number key to configure settings or
to run previously registered applications.
Continue.
Fig. 1.2

11
15 PC card slot For insertion of a separately available PC card.
16 USB port For connection to a computer or other device using a USB cable.
17 Header jack For connection of a commercially available headset (φ2.5mm)
18 Battery pack cover
lock switches
Slide these switches to lock and release the battery pack cover.
19 R Trigger key Press to perform a bar code read operation. This is also pressed to cancel a full
reset.
20 L Trigger key Press to perform a bar code read operation. This is also pressed to cancel a full
reset.
21 Wrist strap hole Connect the wrist strap here.
22 Reader port Emits a laser that reads bar codes.
23 Reset switch Press to reset the handheld terminal.
24 CF card slot unit
terminal
For connection of a separately available CF card Extension Unit.
25 Battery pack cover Covers the compartment that holds the battery pack.

12
1.3.1 DT-167CHGE (Car Mounted Battery Charger)
View
Fig. 1.3
Power Indicator Lamp
Power Contacts
Power Switch
Car plug code jack
Remove button

13
1.3.2 DT-160IOE (Bridge Satellite Cradle)
Views
Table 1.5 Names of parts
No. Part Name Description
1 USB port This port accepts connection of a USB cable for connection to a computer
for transfer of system data and file data. Use of the USB port requires
installation of a special driver on the PC.
2 RS-232C port This port accepts connection of an RS-232C cable for connection to a
computer for transfer of system data and file data. Use of the RS-232C port
requires installation of a special driver on the PC.
3 RS-422 port This port is used when connecting to another Bridge Satellite Cradle.
4 AC adaptor jack Connect the AC adaptor here.
5 Wall mount unit
fastening plate
The holes in this plate accept screws that secure the wall mount unit in place.
6 Terminal detect switch This switch detects when the Handheld Terminal is not seated correctly on
the Bridge Satellite Cradle.
7 IR port This port transfers data with the Handheld Terminal IR port non-contact data
communication.
8 Power supply terminals Power is supplied to the Handheld terminal via these contacts.
Continue.
Fig. 1.4
Back
Top
Front
Right Bottom

14
This lamp indicates the mounting status of the Handheld Terminal.
Off : Power off
Green : Power on, Handheld Terminal mounted correctly
9 Power indicator lamp
Red : Power on, Handheld Terminal not mounted
This lamp shows when the Handheld terminal is performing data
communication.
Off : No data communication being performed
Green flashing : Data communication in progress
10 Communication
indicator lamp
Red : Problem with a connection between two Bridge Satellite
Cradles
This lamp indicates whether the system is operating normally. Regardless of
whether or not a Handheld Terminal is mounted this lamp indicates the system
status and whether or not a communication operation with the system can be
performed.
Off : System is not operating.
11 System status
indicator lamp
Green : System is operating.
12 Power switch Turns the power on and off.
13 Desktop unit This is the base when using the Bridge Satellite Cradle in a desktop
configuration. Remove the desktop unit in the case of a wall-mount
configuration.
14 DIP switches Use these switches to configure the Bridge Satellite Cradle as required.

15
1.3.3 DT-5022CHG (Rapid Battery Charger)
Fig. 1.5
Top
Left Right
Bottom
Views
Charge status
indicators
Dual charger connection terminals
AC adaptor jack
Connection attachments
Battery pack compartments

16
1.3.4 DT-5023BAT/DT-5025LBAT (Battery Packs)
Views
Fig. 1.6
DT-5023BAT DT-5025LBAT
Bottom Bottom
Side Sid
e
Left Left
Top To
p
Charge/Power supply
terminals
Charge/Power
supply terminals

17
2. Hardware Specifications
2.1 DT-X10
Table 2.1
Item Specification Remark
CPU, Memory
CPU Intel PXA255 Application Processor Operating clock; 300 MHz (Max.)
Operating system Microsoft WindowsCE .NET 4.1
RAM 32 MB
FROM 64 MB (user area 30 MB)
Scanner
Method Semi-conductor laser light
Laser emitting window Direct
Laser light wave length 650±10 nm
Output of the light < 1 mW
No. of scannings 100±20 times per second
Resolution 0.127 mm (Minimum)
PCS 0.45 or greater Print Contrast Signal
Depth 40 to 300 mm
Maximum 30 mm (at the depth 40 mm)Readable width
Maximum 238 mm (at the depth 300 mm)
External disturbed light 50,000 Lux or less under the sunlight
Readable symbologies UPC-A, UPC-E, EAN, NW7, Code39,
Code93, Code128, EAN128,
Interleaved2of5, MSI, IATA. ITF
Display
Display device 3.5-inch 2-way TFT color LCD
No. of dots 240 (w) x 320 (h)
Dot pitch 0.22 (w) x 0.22 (h) mm
Backlight LED
Display font type Scalable fonts See note 1
Indicator
Confirmation /Status LED (in red/green) x 2 pcs Left: Programmable
Right: Battery charge status
Input
Keyboard See Chapter 1.3 “General Guide”.
Trigger key 2 keys ( left and right sides)
Touch panel Plastic panel (Resolution 240 x 320)
Possible to display character input pad
IrDA interface
Standard IrDA Ver. 1.1 compatible
Communication method Half duplex
Synchronization Start/Stop bit
Baud rate (bps) 9,600, 115,200, 4M
Communication range 0 to 1 m (Maximum 25 cm at 4 Mbps)
Bluetooth
Standard Bluetooth® Specification Ver. 1.1
Communication range 3 m Depending on the surrounding
conditions
Output Maximum 3 dBm (PowerClass2)
Continue.

18
Serial interface
Standard USB slave Connector: USB mini-B 5-pin
Transmission speed 12 Mbps (Max.)
Audio
Earphone output, Microphone
input
φ2.5
PC card (applicable to DT-X10M10E)
Specification PC card Type I/II (3.3V/5.0V)
Supply current 450 mA (5.0V), 500 mA (3.3V) Constant supply current values
Wireless LAN interface (applicable to DT-X10M10RC and DT-X10M10RC2)
Frequency category ISM
Standard IEEE802.11b See note 2
Modulation Direct Sequence (“DS”)
Frequency band 2,400 MHz to 2,483.5 MHz
Transmission speed 11 Mbps (Maximum)
Communication range Indoor 50 m, Outdoor 150 m The range may vary depending on the
environment.
No. of channels 13 (ETSI) 3 channels for concurrent use.
Other features Roaming within multiple
Access-Points
CF card interface
Card type CF card Types I/II (3.3V)
Supply current 500 mA (3.3V) maximum
CF extension slot (Option)
Power
Operating power Lithium-ion battery pack x 1pc DT-5023BAT or DT-5025LBAT
Memory backup power Lithium secondary batter x 1pc Built-in, not replaceable 50mAH
Approx. 8 H (DT-5023BAT)
Approx. 18 H (DT-5025LBAT)
Assuming; wait:calculation:scanning 20:1:1
Approx. 4 H (DT-5023BAT)
Battery life
Approx. 10 H (DT-5025LBAT)
Assuming; wait : scanning : wireless LAN
operation 13:3:4
DT-5025LBAT 2 weeksMemory backup by
Lithium-ion battery
pack
DT-5023BAT 1 week
See note 3.
10 minutes for data in RAMMemory backup by
only Lithium secondary
battery
2 weeks for built-in clock
Under conditions with room temperature and
memory backup battery fully charged
See note 4.
Memory backup
battery charge time
4 days A period required to charge the memory backup
battery with DT-5023BAT (or DT-5025LBAT)
being installed in the terminal.
Power consumption DC2.5A/ DC3.7 to 5.0V
Buzzer
Sound pressure 70 dB or greater
Weight
Approx. 360 g DT-X10M10E
Approx. 410 g DT-X10M10RC/M10RC2
Dimensions
Approx. 220(D) x 77(W) x 47 (H) mm
Notes:
1. A font that can be used to print characters of any size.
2. Concurrent use of Wireless LAN communication with Bluetooth communication is not recommended.
3. Each memory backup period will depend on the characteristic of terminal itself, the surroundings including
temperature, humidity. Thus, the periods described in Table 4.1 are recommended for use for reference
only. They are not guaranteed figures.
4. Backup for both data in RAM and the RTC (built-in clock) will commence when the battery pack (either
DT-5023BAT or DT-5025LBAT) runs down.

19
2.2 DT-160IOE (Bridge Satellite Cradle)
Table 2.2
Item Specification Remark
Standard IrDA Ver. 1.1 compatible
Comm. method Half duplex
Synchronization Start/stop method
IrDA
Comm. speed 4 Mbps (maximum)
Standard USB Ver. 1.1 compatible
Comm. speed 12 Mbps (maximum)
USB
Connector
USB connector type B
1. VBus
2. –Data (D-)
3. +Data (D+)
4. GND
Comm. method Full duplex
Synchronization Start/stop method
Comm. speed 115.2 Kbps
RS-232C
Connector
D-Sub 9-pin (Male)
Comm. method Full duplex
Synchronization Start/stop method
Comm. speed 115.2 Kbps
Interface
RS-422
Connector
RJ-45 compatible (6 pins)
No. of LEDs 3
No. of display colors 2 Red, green
Display Status LED
Display content
System operation status (“LINE”)
Comm. status (“DATA”)
Power status (“POWER”)
Refer to Chapter 2.6
“Status Indication
With LEDs”.
DIP switch 8 switches See page 22.
Input Detection switch for DT-X10 Push switch
Input voltage DC 12V±5%
Consumption current
Approx. 1,600 mA While supplying
power or transmitting
data.
Plug EIAJ RC-5320A Class 4 Center: plus
Input from AC
adaptor
AC adaptor AD-S42120AE
Output voltage DC 5V±10%
Output current 2,500 mA (maximum)
Charge method Constant voltage With curb function on
current
Approx. 2.5 hours For DT-5023BAT
Power
Charge/supply
power
Charge time Approx. 5.0 hours For DT-5025LBAT
Continue.
2
1
3
4
4
1
3
2
12
SG ER SD RD CD
S
E
S
R
C
C
C
R
D
5
4
3
2
1
9
8
7
6
CI CS RS D
RDI-
RDI+
SDO-
SDO+
RSO-
RSO+
5
4
3
2
1
6
OU
T
5
4
3
2
1
6
IN
RD0-
RDO+
SDI-
SDI+
RSI-
RSI+

20
Power supply terminals
The illustration of
the power supply
terminals on the left
is viewed at the
front of the cradle.
Weight/Dimensions
Table 2.3
Specification Remark
In desktop state Approx. 490 g
Weight In wall mount state Approx. 650 g
In desktop state Approx. 110 (W) x 139 (D) x 129 (H) mm
Dimensions In wall mount state Approx. 110 (W) x 148 (D) x 153 (H) mm
2.3 DT-167CHGE (Car Mounted Battery Charger)
Table 2.4
Item Specification Remark
No. of LEDs 1
No. of display colors 2 In red and green
Display content Power status (“POWER”)
Indicates the status of terminal being mounted on the charger.
OFF : Power is OFF.
Flashing in green : Power is ON and the terminal is mounted on the charger.
Display Status LED
Flashing in red : Power is ON but the terminal is not mounted on the charger.
Input Detection switch for DT-X10 Push switch
Input voltage DC 12V/24V±5%
DC 12V :Approx. 1,400 mA
Consumption current DC 24V : Approx. 700 mA
While supplying
power.
Plug EIAJ RC-5320A Class 4 Center: plus
Input from
power adaptor
Power cord DT-827CAC
Output voltage DC 5V±10%
Output current 2,500 mA (maximum)
Charge method Constant voltage With curb function
on current
Approx. 2.5 hours For DT-5023BAT
Charge time Approx. 5.0 hours For DT-5025LBAT
Power
Charge/supply
power
Power supply terminals
The illustration of
the power supply
terminals on the left
is viewed at the
front of the charger.
Weight/Dimensions
Table 2.5
Specification Remark
Weight Approx. 755 g
Dimensions Approx. 119 (W) x 267 (D) x 123 (H) mm
GND
Power supply
terminals
GND
Power supply
terminals