Casio 3416 User manual

Operation Guide 3416
E-9
Illumination
In any mode, press Lto illuminate the display for about two seconds.
Illumination may be hard to see when viewed under direct sunlight.x
Illumination turns off automatically whenever an alarm sounds.x
Frequent use of illumination runs down the battery.x
E-8
After you set the time and date, press5. Ato return to the Timekeeping Mode.
E-7
While the seconds digits are selected (flashing), press3. Dto reset the seconds to
00. If you press Dwhile the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range of
00 to 29, the minutes count is unchanged.
While any other digits (beside seconds) are selected (flashing), press4. Dto
increase the number or Bto decrease it. While the 12/24-hour format setting is
selected, press Dor Bto toggle it between 12 and 24.
Except for when adjusting the seconds or setting the 12/24-hour format, holdingx
down a button changes the current selection at high speed.
When the 12-hour format is selected, the indicatorxPappears on the display to
indicate “P.M.” times. There is no indicator for “A.M.” times.
When the 24-hour format is selected, the indicatorx24 appears on the display.
The year can be set in the range of 2000 to 2099.x
The watch’s built-in full automatic calendar makes allowances for different monthx
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
The day of the week is displayed automatically in accordance with the date (year,x
month, and day) settings.
E-6
Timekeeping Mode
To set the time and date
Hold down1. Awhile in the Timekeeping Mode until
the seconds digits flash on the display because they
are selected.
Press2. Cto change the selection in the following
sequence.
12/24-Hour Format
C
C
C
Seconds Hour Minutes
Day Month Year
CC
C
C
Seconds
Day of week
Month – Day
Vibration alarm on indicator
(page E-10)
PM indicator
Minutes
Hour
E-5
This watch returns to the Timekeeping Mode whenever you hold down thexCbutton
for one or two seconds. If you ever lose track of what mode you are in or what you
should do next, hold down Cto return to regular timekeeping.
In any mode pressxLto illuminate the display.
CC
C
Stopwatch Mode Alarm Mode Dual Time Mode
E-4
General Guide
PressxCto change from mode to mode.
After you perform an operation in any mode, pressingxCreturns to the Timekeeping
Mode.
If you do not press any button for a few minutes while making settings in any modex
(indicated when settings are flashing), the watch automatically clears the setting screen
(settings stop flashing) and returns to the normal display for the mode you are in.
C
Timekeeping Mode Countdown Alarm Mode
C
E-3
Procedure Lookup
The following is a handy reference list of all the operational procedures contained in
this manual.
To set the time and date ......................................................................................... E-6
To turn the vibration alarm on and off................................................................. E-11
To set the countdown start time .......................................................................... E-12
To use the countdown alarm................................................................................ E-13
To turn the Auto-Start function on and off.......................................................... E-16
To set the alarm time............................................................................................. E-17
To turn the daily alarm and hourly time signal on and off ................................ E-19
To test the alarm sound........................................................................................ E-20
To set the Dual Time ............................................................................................. E-21
E-2
Contents
General Guide.......................................................................................................... E-4
Timekeeping Mode .................................................................................................. E-6
Illumination .............................................................................................................. E-9
Vibration Alarm...................................................................................................... E-10
Countdown Alarm Mode ....................................................................................... E-12
Stopwatch Mode.................................................................................................... E-14
Alarm Mode............................................................................................................ E-17
Dual Time Mode..................................................................................................... E-21
Specifications ........................................................................................................ E-23
E-1
About This Manual
Note that the product illustrations in this manual are intended for reference only,x
and so the actual product may appear somewhat different than depicted by an
illustration.
All explanations in this manual use expressions such as “sounds the alarm” forx
alarm operations. When the Vibration Alarm is turned on, these expressions should
be understood to mean “causes the watch to vibrate” (page E-10).
MA1210-EA
Ú
#!3)/#/-054%2#/,4$

Operation Guide 3416
E-19
To turn the daily alarm and hourly time signal on and off
Press Bwhile in the Alarm Mode to change the status of the daily alarm and hourly
time signal in the following sequence.
B B B
Both OFF Daily Alarm
Only
Hourly Time
Signal Only
Both ON
B
The alarm on indicator (x) and the Hourly Time Signal on indicator ( ) are shown
on the display in all modes while these functions are turned on.
E-18
Press3. Dto increase the selected digits and Bto decrease them. Holding down
either button changes the selection at high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you selectx
for regular timekeeping.
When setting the alarm time using the 12-hour format, take care to set the timex
correctly as morning (no indicator) or afternoon (P).
After you set the alarm time, press4. Ato return to the Alarm Mode.
E-17
Alarm Mode
When the Daily Alarm is turned on, an alarm operation
(20-second tone or 10-second vibration) is performed
at the preset time each day. Press any button to stop
the alarm after it starts to sound. When the Hourly Time
Signal is on, the watch beeps every hour on the hour.
To set the alarm time
Hold down1. Auntil the hour digits start to flash on
the display. The hour digits flash because they are
selected.
x This operation will switch the Daily Alarm on
automatically.
Press2. Cto change the selection in the following
sequence.
Hour Minutes
C
Hourly time signal
on indicator
Current time
Alarm on indicator
Minutes
Hour
Mode indicator
E-16
About the Auto-Start function
With the Auto-Start function, the watch performs a 5-second countdown. When the
countdown reaches zero, stopwatch operation starts automatically. During the final
three seconds of the countdown, a beeper sounds with each second.
To turn the Auto-Start function on and off
While the display is showing all zeros in the Stopwatch Mode, press Bto toggle it
on and off.
The indicatorxAUTO-ST appears and 05 is shown in the upper display while Auto-
Start is turned on. The AUTO-ST indicator is not shown and the upper part of the
display shows the current time when Auto-Start is turned off.
E-15
(a) Elapsed time measurement
DDDDB
Start Stop Re-start Stop Reset
(b) Split time measurement
DBBDB
Start Split Split release Stop Reset
(c) Split time and two finishes
DBDBB
Start Split
First runner
finishes.
Stop
Second runner
finishes.
Record time of
first runner.
Split release
Record time of
second runner.
Reset
E-14
Stopwatch Mode
The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes. The range of the stopwatch
is 23 hour, 59 minutes, 59.99 seconds. The Stopwatch
Mode also features an Auto-Start function.
1/100 Seconds
Seconds
Minutes
Current time
Mode indicator
E-13
Press3. Dto increase the selected number or Bto decrease it. Holding down either
button changes the selection at high speed.
PressxDand Bat the same time to clear the starting time to 0:00' 00".
To set the starting value of the countdown time to 24 hours, set 0:00' 00".x
After you set the countdown start time, press4. Atwice to return to the Countdown
Alarm Mode.
To use the countdown alarm
Press1. Dwhile in the Countdown Alarm Mode to start the countdown alarm.
Press2. Dagain to stop the countdown alarm.
You can resume countdown alarm operation by pressingxD.
Stop the countdown alarm and then press3. Bto reset the countdown time to its
starting value.
When the end of the countdown is reached, the alarm sounds for 10 seconds orx
until you stop the alarm by pressing any button. Countdown timing stops and the
countdown time is automatically reset to its starting value after the alarm stops.
E-12
Countdown Alarm Mode
The countdown alarm can be set within a range of
1 second to 24 hours. When the countdown reaches
zero, an alarm sounds for 10 seconds or until you press
any button.
To set the countdown start time
Hold down1. Awhile in the Countdown Alarm Mode.
The hours digits flash on the display because they
are selected.
Press2. Cto change the selection in the following
sequence.
CC
Hour Minutes Seconds
C
1/10 Seconds
Seconds
Minutes
Mode indicator
Current time
E-11
To turn the vibration alarm on and off
In the Timekeeping Mode, hold down Dfor about
two seconds to toggle the Vibration Alarm between on
(Vibration Alarm on indicator displayed) and off (indicator
not displayed).
The watch will vibrate when you toggle to on, and beepx
when you toggle to off.
Turning off the Vibration Alarm also disables the buttonx
operation tone.
Vibration alarm on indicator
E-10
Vibration Alarm
When the Vibration Alarm is turned on, the watch vibrates instead of sounding an
alarm. This lets you use the watch without disturbing others by beeping sounds.
The Vibration Alarm can be used to replace alarm sounds in the Countdown Alarm,x
Stopwatch, and Alarm Modes.
All explanations in this manual use expressions such as “sounds the alarm” forx
alarm operations. When the Vibration Alarm is turned on, these expressions should
be understood to mean “causes the watch to vibrate”.
Watches with a metal band may produce a noise when a vibration operationx
is performed. This is due to vibration of the metal band, and does not indicate
malfunction of the watch.

Operation Guide 3416
E-24
Dual Time
Other: LED (light-emitting diode); Vibration alarm
Battery: One lithium battery (Type: CR2032)
Battery life: 10 years under the following conditions
One 2-second light operation per dayx
One alarm operation per dayx
Note: One alarm operation is 20-second audible alarm or 10-second vibration
alarm.
E-23
Specifications
Accuracy at normal temperature: ± 30 seconds a month
Timekeeping: Hour, minutes, seconds, pm (P), day of the week, month, day
Time format: 12-hour and 24-hour formats
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Countdown Alarm
Measuring unit: 1/10 second
Input range: 1 second to 24 hours
Stopwatch
Measuring unit: 1/100 second
Measuring capacity: 23 hours 59 minutes, 59.99 seconds
Measuring modes: Elapsed time, split time and two finishes
Other: Auto-Start
Alarm: Daily alarm, hourly time signal
E-22
After you set the time, press4. Ato return to the Dual Time Mode.
In the Dual Time Mode, the seconds count is synchronized with the seconds countx
of the Timekeeping Mode.
In the Dual Time Mode, pressxBto toggle between the 12-hour and 24-hour
formats.
E-21
Dual Time Mode
The Dual Time Mode lets you keep track of the time in
another time zone. You can also select the timekeeping
format (12-hour or 24-hour) separately from the
Timekeeping Mode.
To set the Dual Time
Hold down1. Awhile in the Dual Time Mode. The hour
digits flash on the display because they are selected.
Press2. Cto change the selection in the following
sequence.
Hour Minutes
C
Press3. Dto increase the selected digits and Bto
decrease them. Holding down either button changes
the selection at high speed.
Current time
Mode indicator
Minutes
Hour
E-20
To test the alarm sound
Hold down Bwhile in the Alarm Mode to sound the alarm.
Note that pressingxBalso changes the alarm and the hourly time signal ON/OFF
settings.