Casio 5565 User manual

Operation Guide 5565
E-9
Initial Screens
xWhen you enter the Telememo, World Time, or Alarm Mode, the data you were
viewing when you last exited the mode appears first.
E-8
Auto Return Feature
xThe watch automatically returns to the Timekeeping Mode if you do not perform
any button operation for two or three minutes in the Telememo, Alarm, or Hand
Setting Mode.
xIf you leave a screen with flashing digits or a cursor on the display for two or three
minutes without performing any operation, the watch automatically exits the setting
screen.
xHolding down Bfor about one second in any mode jumps directly to the
Timekeeping Mode. This operation does not work while a setting screen is on the
display.
Scrolling
xThe Cand Dbuttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a
scroll operation scrolls through the data at high speed.
E-7
Stopwatch Mode Hand Setting Mode
B
Alarm Mode Countdown Timer
Mode
B B B
E-6
General Guide
xPress Bto change from mode to mode. After you perform an operation (except
for C) in any mode, pressing Breturns to the Timekeeping Mode.
xTo return to the Timekeeping Mode from any other mode, hold down Bfor about
one second.
Timekeeping Mode World Time ModeTelememo Mode
B BB
E-5
Illumination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-38
To turn on illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-38
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-39
Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-41
User Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-52
E-4
World Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-25
To set the World Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-26
To view the time in another city code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-27
To toggle a city code time between
Standard Time and Daylight Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . E-28
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-29
To set an alarm time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-30
To test the alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-32
To turn an alarm and the Hourly Time Signal on and off . . . . . . . . . . . . . . . . . E-32
Countdown Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-34
To set the countdown start time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-34
To use the countdown timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-35
Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-36
To measure times with the stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-37
E-3
Contents
About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2
General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6
Timekeeping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10
To set the digital time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-11
To toggle between 12-hour and 24-hour timekeeping . . . . . . . . . . . . . . . . . . E-14
To toggle the Timekeeping Mode digital time between
DST and Standard Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-15
To adjust the analog time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16
Telememo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17
To create a new Telememo record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18
To recall Telememo records. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-22
To edit a Telememo record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-23
To delete a Telememo record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-23
E-2
About This Manual
xDepending on the model of your watch, display text
appears either as dark figures on a light background, or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
xButton operations are indicated using the letters shown in
the illustration.
xNote that the product illustrations in this manual are
intended for reference only, and so the actual product may
appear somewhat different than depicted by an illustration.
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
To ensure that this watch provides you with the years of service for which it is
designed, carefully read and follow the instructions in this manual, especially the
information under “Operating Precautions” and “User Maintenance”.
Be sure to keep all user documentation handy for future reference.
MA1709-EA © 2017 CASIO COMPUTER CO., LTD.

Operation Guide 5565
E-19
(space) Ato Z@to —0to 9
DDD
C
D
CCC
xYou can input spaces, alpha characters, symbols, and numbers in a name. For
details, see the “Character List” at the back of this manual.
4. When the character you want is at the cursor position, press Bto move the
cursor to the right.
5. Repeat steps 3 and 4 until the name is complete.
xYou can input up to eight characters for the name.
6. After you input the name, press Bas many times as
necessary to move the cursor to the number field.
xYou can tell when you are in the name field because
of the long cursor (—). The number field has a short
cursor ( – ).
E-18
To create a new Telememo record
1. In the Telememo Mode, press Cand Dat the same
time to display the new data screen.
xThe new data screen shows ———, which indicates
that there is no text in the name field.
xIf the new data screen does not appear, it means that
memory is full. To store another record, you will first
have to delete some of the records stored in memory.
2. Hold down Auntil the flashing cursor (—) appears
in the name field of the display, which indicates the
setting screen.
3. Use Dand Cto change the character at the cursor
position in the name field. The character changes in
the following sequence.
New Data Screen
E-17
Telememo
Telememo lets you store up to 30records, each
containing name and telephone number data. Records
are automatically sorted based on the characters of the
name. You can recall records by scrolling through them
on the display.
xA Telememo Mode record has a name field and a
number field.
xSee “Character List” at the back of this manual for
details on how the watch sorts records.
xAll of the operations in this section are performed in
the Telememo Mode, which you enter by pressing B
(page E-6).
Name
Remaining memory
Record number
Number
E-16
To adjust the analog time
1. In the Timekeeping Mode, press Bsix times to enter
the Hand Setting Mode (page E-7).
2. Hold down Auntil the current digital time starts to
flash, which indicates the analog setting screen.
3. Press Dto advance the analog time setting by
20seconds.
xHolding down Dadvances the analog time setting
at high speed.
xIf you need to advance the analog time a long way, press Dand Cat the
same time. This locks the high speed hand movement, so you can release the
two buttons. High-speed hand movement continues until you press any button.
It will also stop automatically after the time advances 12hours or if an alarm
(daily alarm, Hourly Time Signal, or countdown alarm) starts to sound.
4. Press Ato exit the setting screen.
xTo return to the Timekeeping Mode, press B.
E-15
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down Auntil the
seconds start to flash, which indicates the setting
screen.
2. Press Bonce to display the DST setting screen.
3. Press Dto toggle between Daylight Saving Time
(ONdisplayed) and Standard Time (OFF displayed).
4. Press Ato exit the setting screen.
xThe DST indicator appears on the Timekeeping,
Alarm, and Hand Setting Mode to indicate that
Daylight Saving Time is turned on.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does
not match the time of the digital display.
E-14
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press Dto toggle between 12-hour timekeeping, or
24-hour timekeeping.
xWhile the 12-hour format is selected for timekeeping, a P(PM) indicator will appear
for times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
P(PM) indicator.
xThe 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use
Daylight Saving Time.
E-13
4. Press Ato exit the setting screen.
xResetting the seconds only (without changing the hour, minute, or DST setting)
causes the analog minute hand setting to be adjusted automatically. If you
change the hour, minute, or DST setting, you should also use the procedure
under “To adjust the analog time” (page E-16) to adjust the analog hands
accordingly.
xSee “Digital Time Daylight Saving Time (DST) Setting” (page E-14) for details about
the DST setting.
xResetting the seconds to 00 while the current count is in the range of 30 to
59causes the minutes to be increased by 1. In the range of 00 to 29, the
seconds are reset to 00 without changing the minutes.
xThe day of the week is automatically displayed in accordance with the date
(year, month, and day) settings.
xThe year can be set in the range of 2000 to 2099.
xThe watch’s built-in full automatic calendar makes allowances for different
month lengths and leap years. Once you set the date, there should be no reason
to change it except after you have the watch’s battery replaced.
E-12
3. When the setting you want to change is flashing, use Cand Dto change it as
described below.
Screen To do this: Do this:
Reset the seconds to 00. Press D.
Toggle between Daylight Saving Time (ON)
and Standard Time (OFF). Press D.
Change the hour or minute.
Use D(+) and C(–).
Change the year.
Change the month or day.
E-11
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and
date. When setting the digital time, you can also configure settings for summer time
(Daylight Saving time or DST).
To set the digital time and date
1. In the Timekeeping Mode, hold down Auntil the
seconds start to flash, which indicates the setting
screen.
2. Press Bto move the flashing in the sequence shown
below to select the other settings.
B
B
Seconds DST
Day
Hour
Month
Minutes
Year
B B B
BB
E-10
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time (page E-11) and analog time (page E-15) are different.
xIn the Timekeeping Mode, press Ato toggle the display between the date screen
and the time screen.
Seconds
Date Screen Time Screen
A
Hour
Day of week
Month – Day
PM indicator
Hour : Minutes
Minutes

Operation Guide 5565
E-29
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other two are daily alarms. You
also can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
xThere are three alarm screens: AL1, AL2, and SNZ
(snooze). The Hourly Time Signal screen is indicated
by SIG.
xAll of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B(page E-7).
Alarm time
(Hour : Minutes)
E-28
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use Dto display the city
code whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down Auntil the DST On/Off setting of the
world time starts to flash, which indicates the setting
screen.
3. Press Dto toggle between Daylight Saving Time
(ON displayed) and Standard Time (OFF displayed).
4. Press Ato exit the setting screen.
xThe DST indicator appears on the World Time Mode display to indicate that
Daylight Saving Time is turned on.
xThe above operation toggles all World Time city codes between Daylight Saving
Time and Standard Time. Note that you cannot make settings for individual city
codes.
E-27
4. While a setting is flashing, use Dand Cto change it.
xPressing Dand Cat the same time while any World Time setting is flashing
causes the displayed time to change to the same setting as the current
Timekeeping Mode time.
xWhile DST On/Off setting is selected (flashing), press Dto toggle between
Daylight Saving Time (ON) and Standard Time (OFF).
xWhile the hour or minutes setting is selected (flashing), use D(+) and C(–) to
change it.
5. Press Ato exit the setting screen.
To view the time in another city code
In the World Time Mode, press Dto scroll through city codes.
E-26
xIf your location is not included in the preset city codes, select the preset city code
that is in the same time zone as your location.
xFor full information on city codes, see the “City Code Table” at the back of this
manual.
To set the World Time
1. In the World Time Mode, press Dto scroll through
city codes.
2. Hold down Auntil the DST On/Off setting of the world
time starts to flash, which indicates the setting screen.
3. Press Bto move the flashing in the sequence shown
below to select the other settings.
DST Hour Minutes
BB
B
E-25
World Time
World Time digitally displays the current time in 30cities
(29time zones) around the world.
xAll of the operations in this section are performed in
the World Time Mode, which you enter by pressing B
(page E-6).
World Time
The time settings of the Timekeeping Mode and the
World Time Mode are independent of each other, so
you must make separate settings for each. This watch
is preset with a number of city codes, each of which
represents the time zone where that city is located.
xWhenever you change the time setting for any city in the World Time Mode, the
settings of all other cities are changed accordingly.
City code
Current time for the
selected city code
E-24
3. Press Cand Dat the same time to delete the record.
xCLR appears to indicate that the record is being deleted. After the record is
deleted, the cursor appears on the display, ready for input.
4. Input data or press Ato return to the Telememo record screen.
E-23
To edit a Telememo record
1. In the Telememo Mode, use Dto scroll through the records and display the one
you want to edit.
2. Hold down Auntil the flashing cursor appears on the display.
3. Use Bto move the flashing to the character you want to change.
4. Use Cand Dto change the character.
xFor details on inputting characters, see “To create a new Telememo record”
(page E-18) (step 3 for name input and 7 for number input).
5. After making the changes that you want, press Ato store them and return to the
Telememo record screen.
To delete a Telememo record
1. In the Telememo Mode, use Dto scroll through the records and display the one
you want to delete.
2. Hold down Auntil the flashing cursor appears on the display.
E-22
To recall Telememo records
In the Telememo Mode, press D(+) to scroll through Telememo records on the
display.
xOnly name data appears when you scroll through Telememo records.
xPress Ato toggle the screen between the name and number fields.
Name Number
A
xThe name and number scroll from right to left on the display. A separator (s) is
inserted between the last character and first character of the data.
xPressing Dwhile the last Telememo record is on the display causes the new data
screen to appear.
E-21
10. Press Ato store your data and return to the Telememo record screen (without
the cursor).
xAfter you press Ato store data, the name flashes for about one second to
indicate that records are being sorted.
xNote that a record must have something input in the name field, otherwise you
will not be able to store it.
E-20
xThe name field has spaces for eight characters, so you must press Bto move
past the 8th character in order to get to the number field.
xThe number field has spaces for 16 digits. Pressing Buntil the cursor moves
past the 16th digit causes it to jump back to the first character of the name field.
7. Use Dand Cto change the character at the cursor position in the number
field. The character changes in the following sequence.
(space) 0to 9 ( + )–
DD DDD
C
D
CC CCC
8. When the character you want is at the cursor position, press Bto move the
cursor to the right.
9. Repeat steps 7 and 8 until you complete number input.
xYou can input up to 16 digits for the number.

Operation Guide 5565
E-39
Specifications
Accuracy at normal temperature: ± 30 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to
2099
Other: 2 screen formats (Date, Time); Daylight Saving Time (summer time)/
Standard Time
Telememo:
Memory capacity: Up to 30 records, each including a name (8 characters) and
telephone number (16 digits)
Other: Remaining memory screen; Auto sort
World Time: 30 cities (29 time zones)
Other: Daylight Saving Time/Standard Time
Alarms: 3 daily alarms (with one snooze alarm); Hourly Time Signal
E-38
Illumination
The face of the watch is illuminated for easy reading in the dark.
To turn on illumination
In any mode (except when a setting screen is on the display), press Cto illuminate
the display for about one second.
Illumination Precautions
xIllumination may be hard to see when viewed under direct sunlight.
xIllumination turns off automatically whenever an alarm sounds.
xFrequent use of illumination runs down the battery.
E-37
To measure times with the stopwatch
Elapsed Time
DD D D A
Start Stop Resume Stop Reset
Split Time
DA A D A
Start Split Split release Stop Reset
Two Finishes
DA D A A
Start Split
First runner finishes.
Display time of first
runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
E-36
Stopwatch
The stopwatch lets you measure elapsed time, split
times, and two finishes.
xThe display range of the stopwatch is 23hours,
59minutes, 59.99seconds.
xThe stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
xAn ongoing elapsed time measurement operation will
continue internally even if you change to another mode.
However, if you exit the Stopwatch Mode while a split
time is displayed, the split time will not be displayed
when you return to the Stopwatch Mode.
xAll of the operations in this section are performed in
the Stopwatch Mode, which you enter by pressing B
(page E-7).
Minutes
Seconds
1/100 second
Hours
E-35
3. While a setting is flashing, use D(+) and C(–) to change it.
xTo set the starting value of the countdown time to 24hours, set 0:00.
4. Press Ato exit the setting screen.
To use the countdown timer
Press Dwhile in the Countdown Timer Mode to start the
countdown timer.
xWhen the end of the countdown is reached, the alarm
sounds for 10seconds or until you stop it by pressing
any button. The countdown time is automatically reset to
its starting value after the alarm stops.
xPress Dwhile a countdown operation is in progress to pause it. Press Dagain to
resume the countdown.
xTo completely stop a countdown operation, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
xThe countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
E-34
Countdown Timer
The countdown timer can be set within a range of
one minute to 24hours. An alarm sounds when the
countdown reaches zero.
xAll of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
B(page E-7).
To set the countdown start time
1. In the Countdown Timer Mode, hold down Auntil the
hour setting of the countdown start time starts to flash,
which indicates the setting screen.
xIf the countdown start time is not displayed, use the procedure under “To use
the countdown timer” (page E-35) to display it.
2. Press Bto move the flashing between the hour and minute settings.
Hours Minutes
Seconds
E-33
xThe above on indicators appear on the display in all modes.
xAn on indicator on the display flashes while its corresponding alarm operation
is sounding.
xThe snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
E-32
To test the alarm
In the Alarm Mode, hold down Dto sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use Dto select an alarm or the Hourly Time Signal.
2. Press Ato toggle it on and off.
xThe indicators shown below appear on the display when the daily alarm
and Hourly Time Signal are turned on. Each indicator disappears when the
corresponding function is turned off.
Alarm 2 on indicator
Snooze alarm on indicator
Alarm 1 on indicator
Hourly time signal on indicator
E-31
4. While a setting is flashing, use D(+) and C(–) to change it.
xWhen setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (Pindicator).
5. Press Ato exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10seconds, regardless of the mode
the watch is in. In the case of the snooze alarm, the alarm operation is performed a
total of seven times, every five minutes, or until you turn the alarm off (page E-32).
xAlarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode digital time.
xTo stop the alarm tone after it starts to sound, press any button.
xPerforming any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
−Displaying the Timekeeping Mode setting screen (page E-6)
−Displaying the SNZ setting screen (page E-30)
E-30
To set an alarm time
1. In the Alarm Mode, use Dto scroll through the alarm
screens until the one whose time you want to set is
displayed.
SNZ AL2AL1 SIG
DDD
D
xTo set a daily alarm, display alarm screen AL1 or AL2. To set the snooze alarm,
display the SNZ screen.
xThe snooze alarm repeats every five minutes.
2. After you select an alarm, hold down Auntil the hour setting of the alarm time
starts to flash, which indicates the setting screen.
xThis operation automatically turns on the alarm.
3. Press Bto move the flashing between the hour and minute settings.

Operation Guide 5565
L-4
x Above table data is current as of January 2017.
x This table shows the city codes of this watch.
x The rules governing global times (UTC offset and GMT differential) and summer
time are determined by each individual country.
L-3
City Code Table
City
Code City UTC Offset/ GMT Differential
PPG PAGO PAGO –11
HNL HONOLULU –10
ANC ANCHORAGE –9
LAX LOS ANGELES –8
DEN DENVER –7
CHI CHICAGO –6
NYC NEW YORK –5
CCS CARACAS –4
RIO
RIO DE JANEIRO –3
– – – –2
– – – –1
LON LONDON 0
PAR PARIS +1
BER BERLIN
CAI CAIRO +2
JRS JERUSALEM
City
Code City UTC Offset/ GMT Differential
JED JEDDAH +3
MOW MOSCOW
THR TEHRAN +3.5
DXB DUBAI +4
KBL KABUL +4.5
KHI KARACHI +5
DEL DELHI +5.5
DAC DHAKA +6
RGN YANGON +6.5
BKK BANGKOK +7
HKG HONG KONG +8
TYO TOKYO +9
ADL ADELAIDE +9.5
SYD SYDNEY +10
NOU NOUMEA +11
WLG WELLINGTON +12
L-2
Character List
L-1
Character List
City Code Table
E-40
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)
Stopwatch:
Measuring unit: 1/100 of a second
Measuring capacity: 23:59'59.99"
Measuring modes: Elapsed time, split time, two finishes
Illumination: LED (light-emitting diode)
Other: 2 analog hands: hour, minutes (hand moves every 20seconds)
Battery: One lithium battery (Type: CR2025)
Approximately 10 years on type CR2025 (assuming alarm operation 10 sec./day
and one illumination operation 1.5 sec./day)
Specifications are subject to change without notice.