Castle Creations Mamba Micro X2 User manual

GETTING STARTED
1. Solder a high quality battery connector to the ESC (see Driver’s Ed Guide
“Connectors and Power Wiring” ).
2. Mount the ESC and motor into the vehicle.
3. Connect motor to the ESC (see Driver’s Ed Guide, “Motor Wiring” ).
4. Plug the RX wire and AUX wire in (see RECEIVER CONNECTION section on the
opposite side).
5. Calibrate your ESC to your radio. (See Driver’s Ed Guide, “How to Calibrate
the ESC” ).
YOU ARE NOW READY TO GO!
Revised 01/2022 Copyright 2022 © Castle Creations P/N:095-0421-00
ABOUT THE MAMBA MICRO X2
Motors
Please note that while the Mamba Micro X2 is capable of handling incredible
amounts of power, your motor must also be up for the task. Always run your
motor within the manufacturer’s specs. Monitor motor, battery, and controller
temps carefully and never let the motor get above 180ºF. Excessive heat in
the motor can damage the motor, the Mamba Micro X2, and your batteries.
Gearing
Always start with stock gearing. If you wish to change the gearing, motor, or
battery, you must check your motor temperature frequently on the first run.
If the motor gets too hot, reduce the pinion size, increase the spur size, or
reduce the pack voltage. Additional information about gearing can be found
online at www.castlecreations.com/microxgearing.
Programming
The Mamba Micro X2 is programmable via your transmitter, Windows® based
PC and a Castle Link USB adapter (available free with enclosed coupon), or
B•Link Bluetooth® Adapter (purchased separately). See the Driver’s Ed Guide
for more instructions on transmitter programming and the Castle Link system
(“Transmitter Programming”, and “Tuning with Castle Link”).
Driver’s Ed Guide
For more detailed information regarding Getting Started,
Throttle Calibration, using Castle Link, or Transmitter
Programming, please refer to the Driver’s Ed Guide by
visiting: www.castlecreations.com/MICROX2DEG
AUX Wire
Waterproof
Switch
RX Wire
Motor B
Motor A LEDs
Sensor Harness/Dust Cover
Motor C
Negative Battery
Wire
Positive Battery
Wire

MAMBA MICRO X2 SPECIFICATIONS
Application
Guidelines
1:18th: vehicles weighing up to 2.25lbs
1:14th: vehicles weighing up to 3lbs
Crawling: low speed crawling up to 9lbs
Input Voltage
Range Min: 2S LiPo, Max: 4S LiPo, 16.8V
BEC
Specifications Adjustable: 5.5V or 7.5V (2A Peak), default 5.5V
Waterproof Yes*
Sensors Yes, with Sensor Harness (P/N 011-0108-00). Included with 1:14/
Crawler edition, sold separately with 1:18th edition.
Product Use
Statement**
• Applying voltages higher than 16.8V will cause irreparable damage to
your controller, voiding the warranty.
• Recommended battery capacity for 1:18th scale vehicles is 1500mAh.
30C continuous discharge. For 1:14th scale vehicles and crawler,
≥2,000mAh, 30c is recommended.
• The Mamba Micro X2 1:18th edition uses 3.5mm motor bullets; the
1:14th/crawler edition uses 4mm on the motor wires and the battery
input wires are bare. You must add the connector of your choice to
the battery leads. We recommend a high current connector rated for
at least 40 amps.
• Do not use 4s LiHV
RECEIVER CONNECTION
RX Wire Plug the RX wire into the throttle (#2) channel on your receiver.
AUX Wire
The AUX wire allows you to adjust a setting “on-the-fly” using an
auxiliary channel on your receiver. The AUX wire function is disabled
by default and is programmable via Castle Link. Plug this wire into the
auxiliary (#3/#4) channel on your receiver.
Contact
Castle Creations
540 North Rogers Road
Olathe, KS 66062
Support: www.castlecreations.com/contact-support
Sales: www.castlecreations.com/contact-service
Website: www.castlecreations.com/mambamicrox
TRANSMITTER PROGRAMMING REFERENCE
AUDIBLE ALERT REFERENCE
• • Start Fail
• –
Low Voltage Cutoff
– • Over-Current
• • • Sensors Lost
• • –
Radio Glitch
• – • Over-Temperature
• – –
Excessive Load
– • • AUX Wire Radio Glitch
– – • Motor Over-Temperature
1.Brake/Reverse Type 3. Brake Amount 5. Motor Type
•With Reverse* •25% •Brushless*
• • Without Reverse • • 50%* • • Brushed Reversing
• • • Crawler Reverse • • • 75%
• • • • 100% 6. Motor Direction
2.Voltage Cutoff •Normal*
•Auto-Lipo* 4. Drag Brake • • Reverse
• • None •Disabled*
• • 10%
• • • 20%
• • • • 30%
• • • • • Crawler Full On *Default Setting
*Not intended for operation while submerged in liquid. If unit is operated in wet conditions, rinse with fresh
water to remove dirt or corrosives, then fully dry unit.
**Failure to adhere to the Product Use Statement constitutes a violation of the warranty agreement, and will
result in non-warranty service fees to repair or replace damaged products.