Catch Fitness YN0311 User manual

YN0311
RACK WITH LAT PULLEY
Assembly
Instructions

catalog
Catalogue ..............................................................................................................1
Security Measures........................................................................2
Exploded View.............................................................3
Parts List........................................................................................................4-7
Installation Guide.......................................................................................8-21
Maintenance Tips...................................................................................................22

Security Measures
Security Measures
To ensure your safety, please read the following notes before using this product.
1. Please read and understand the manual and all warning labels before use.
(It is recommended to familiarize yourself with the normal operation and usage of the device
before using this product. Relevant information can be obtained in this manual and local
retailers)
2. Please keep this manual and make sure all warning labels are clear and complete.
3. This product is recommended for installation by two or more people.
4. Please consult your doctor for advice before you start exercising.
5. Please ensure safety when children are present.
6. Please be cautious when using it off-site with children.
7. Please check the steel wire rope regularly for any signs of wear. If there is wear, it m
ay cause certain danger to you.
8. Please keep your hands, limbs, and clothes stretched so that you can use the device
fully and safely.
9. Please pay attention to any signs that may occur in the machine, including wear of p
arts, loose hardware and welding cracks. If any of the above signs are found, immediate
ly stop using the device and contact our after-sales service department.
10. You can use a wrench or Allen wrench to complete the assembly.
11. The weight of the user of this product shall not exceed 120kg
12. The product is subject to change without notice, and the final interpretation right b
elongs to our company.

Exploded View
YN0311
Executive standard： GB17498-2008.1

Parts List
NO
NAME
NO
SERIAL
NUMBER
NAME
QTY
1
UprightA
2
20
Hex boltsM10X70
18
2
Front post
2
21
Hex boltsM10X120
14
3
Top border
connection
2
22
M10Flat gasket
64
4
UprightB
1
23
M10Locknut
32
5
UprightC
1
24
Barrel casing
1
6
Connect up behind
the border
1
25
Pulley frame
1
7
Bezel back and
bottom connection
1
26
High handle
1
8
Pull-up connection
1
27
Low pull handle
1
9
Post to the ground
1
28
C buckle
4
10
Counterweight
1
29
plug
4
11
Guide rod
2
30
12
Upper beam
1
31
13
High pull-up
connection
1
32
14
Barrel turret
1
33
15
Protection bar
2
34
16
Parallel bar handle
2
35
17
Shelf
2
36
18
High-drawn
wire rope
1
37
19
Low-drawn wire
rope
1
38

Parts List

Installation Guide

Installation Guide

Installation Guide

Installation Guide

Installation Guide

Installation Guide
1. Please use a wrench to tighten all bolts and nuts.

2. Your device is now fully assembled.
3. Please check that all pulleys and wire ropes have been fixed before correct use.
4. In the first stage of use, make certain adjustments to the wire rope according to the
actual situation.
Maintenance
Maintenance Tips:
In order to prolong the service life of the equipment, the parts must be lubricated on ti
me. This product has been initially lubricated for the equipment before leaving the facto
ry, but after a certain period of use, necessary lubrication and maintenance must be car
ried out between the guide rod and the weight plate.
Note: It is forbidden to use oil and butter, otherwise it will absorb dust and dirt in the
air. Sewing machine oil is recommended
1. All pulleys and wire ropes should be checked regularly for
signs of wear.
2. Regularly check and adjust the tension of the wire rope.
3. Regularly check all moving parts and determine whether
there are signs of wear and damage. If there is any problem,
you must stop using the device immediately and contact our
after-sales department.
4. During the inspection, you must make sure that all bolts and
nuts are completely fixed. If any bolts or nuts are loosened,
please lock them in time.
5. Check that there is no crack in the weld.
6. Failure to perform routine maintenance may result in
personal injury or equipment damage.