CDP UPO22 User manual

Please comply with all warnings and operating
instructions in this manual strictly. Save this
manual properly and read carefully the following
instructions before installing the unit. Do not
operate this unit before reading through all
safety information and operating instructions
carefully.

2
1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 3
2. INSTALLATION AND OPERATION .................................................................................................... 6
3. OPERATIONS.....................................................................................................................................11
4. TROUBLE SHOOTING...................................................................................................................... 25
5. STORAGE AND MAINTENANCE..................................................................................................... 26
6. SPECIFICATIONS ............................................................................................................................. 30

1. Safety and EMC instructions
1-1. Transportation and Storage
1-2. Preparation
1-3. Installation
3

1-4. Operation
1-5. Standards
* Safety
* EMI
*EMS
Warning:
4

2. Installation and Operation
2-1. Unpacking and Inspection
NOTE:
5

2-2. Rear Panel View
Diagram : Rear Panel
6

2-3. Single UPS Installation
NOTE:
NOTE 1:
NOTE 2:
NOTE 3:
NOTE 1:
NOTE 2:
NOTE 3:
7

Warning:
Warning:
NOTE:
2-4. UPS Installation for Parallel System
NOTE:
8

2- . Software Installation
9

3. Operations
3-1. Button Operation
Button
Function
3-2. LED Indicators and LCD Panel
LED Indicators:
10

LCD Panel:
Display
Function
Discharge time information
Fault information
Mute operation
Output & Battery voltage information
VAC
VDC
Hz
Load information
Mode operation information
11

Battery information
Input & Battery voltage information
VAC
VDC
Hz
3-3. Audible Alarm
Description
Buzzer status
Muted
UPS status
Warning
Fault
3-4. Single UPS Operation
1. Turn on the UPS with utility power supply (in AC mode)
NOTE:
NOTE:
2. Turn on the UPS without utility power supply (in Battery mode)
3. Connect devices to UPS
12

4. Charge the batteries
5. Battery mode operation
6. Test the batteries
7. Turn off the UPS with utility power supply in AC mode
NOTE 1:
13

NOTE 2:
8. Turn off the UPS without utility power supply in Battery mode
9. Mute the buzzer
10. Operation in warning status
11. Operation in Fault mode
12. Operation of changing battery numbers
14

3-5. Parallel Operation
1. Parallel system initial startup
Turn on the parallel system in AC mode:
Turn on the parallel system in Battery mode:
NOTE:
If more detailed information is needed, please contact supplier or service center for parallel
operation instruction.
2. Add one new unit into the parallel system
3. Remove one unit from the parallel system
15

Warning:
3-6. Abbreviation Meaning in LCD Display
Abbreviation
Display content
Meaning
16

3-7. LCD Setting
Note: Up Down
Programs available list for parameter 1:
17

01: Output voltage
Interface
Setting
Parameter 3: Output voltage
208:
220:
230:
240:
02: Output frequency
Interface
Setting
60 Hz, Normal mode
50 Hz, CVCF mode
ATO
Parameter 2: Output Frequency
50.0Hz:
60.0Hz:
ATO:
Parameter 3: Frequency mode
CF:
NCF:
Note: For single unit, it will have bypass output for a couple of seconds after the unit is powered
on. Therefore, to avoid damage on connected devices, it s strongly suggested to add an additional
Output relay board for CVCF application.
03: Voltage range for bypass
Interface
Setting
Parameter 2:
Parameter 3:
18

04: Frequency range for bypass
Interface
Setting
Parameter 2:
Parameter 3:
05: ECO mode enable/disable
Interface
Setting
Parameter 3:
DIS:
ENA:
06: Voltage range for ECO mode
Interface
Setting
Parameter 2:
Parameter 3:
07: Frequency range for ECO mode
Interface
Setting
Parameter 2:
Parameter 3:
08: Bypass mode setting
Interface
Setting
Parameter 2:
OPN
FBD
Parameter 3:ENADIS
19