cef Idea Island CEF-ID34-8 User manual

Idea Island
Assembly Instructions
KIDS
Our Customers. Our
Inspiration.
We should all try to be
more like them

Components
What’s in the Box!
•LEGS (4)
•HEAVY DUTY 5” CASTERS (4)
•ELECTRIC COVER (1)
•CONNECTOR ANGLE (2)
•LEG COVER (4)
•RATCHET FASTENER: NYLON BLACK (28)
•Serrated NUT ¼ 20” (8)
•FLAT WASHERS (28)
•HEX CAP BOLT ¼ 20” X 3/4” (28)

Tools
What you will need!
Heavy Duty 5” Casters Electric Cover Connector Angle
Legs Leg Cover Flat Washers
Hex Cap Bolt ¼ 20 x ¾ Ratchet Fastener: Nylon Black Serrated Nut ¼ 20

•Standard Allen Wrench 5/32nd
•Standard ¾” Wrench

Lets Get Started!
1)
PAIR ONE HEX CAP BOLT AND ONE FLAT
WASHER AND INSERT INTO EACH HOLE ON THE
LEG
TO AVOID ADDITIONAL MOVEMENT AND TO
ASSIST IN THE ALIGNMENT PROCESS, DO NOT
TIGHTEN BOLTS COMPLETELY UNTIL BOTH LEGS
ARE SET IN PLACE
REMOVE SOLID MAPLE BUTCHER BLOCK FROM
BOX AND PLACE IT DOWN ON A SMOOTH
SURFACE. INSERTS SHOULD BE EXPOSED AS
SHOWN
PLACE ONE LEG AT A TIME AND ALIGN THE
HOLES WITH THE INSERTS IN EACH CORNER AS
SHOWN
2)
3)

4)
5)
6)
AFTER INSERTING THE BOLTS IN EACH
DESIGNATED HOLE, THE LEGS SHOULD BE
ALIGNED AS SHOWN IN THE IMAGE TO THE LEFT
*YOU ARE NOW READY TO TIGHTEN THE BOLTS
SECURELY USING THE RECOMMENDED 5/32ND
ALLEN WRENCH
ALIGN THE CONNECTOR ANGLE TO THE HOLES
IN THE LEGS AS SHOWN TO LEFT AND INSERT
HEX CAP BOLTS WITH WASHERS AND TIGHTEN

7)
8)
USING THE LEG COVER AND RATCHET FASTNERS,
PLACE THE LEG COVER OVER LEG AND ALIGN
WITH PRE-DRILLED HOLES. PLACE ONE RATCHET
FASTNER PER HOLE AND SIMPLY SNAP IN PLACE
*REPEAT THIS STEP ACCORDINGLY
TAKE ONE OF THE HEAVY DUTY 5” CASTERS AND
INSERT IT ON THE TOP OF YOUR LEG INTO
DESIGNATED HOLE.
TAKE THE RECOMMENDED ¾” WRENCH AND
TIGHTEN DOWN THE SPECIFIED BOLT TO THE
LEFT UNTIL IT CANNOT GO DOWN ANY FURTHER
ADDITIONALLY, CONNECT THE PROVIDED ¼” 20
SERRATED NUTS TO THE BACK OF THE BOLT AND
TIGHTEN SECURELY AS SHOWN
*REPEAT STEPS 4-6 FOR REMAINING TABLE LEGS

9)
THE ELECTRICAL UNIT WILL ALREADY BE
CONNECTED TO YOUR BUTCHER BLOCK
TABLE AS SHOWN
UNWRAP THE CORD AND EXTEND THE
CORD LONG WAYS DOWN THE CHANNEL
PLACE THE ELECTRICAL COVER OVER
THE CHANNEL
LINE HOLES UP WITH THE
COORDINATING HOLES ON THE LEGS AS
SHOWN
PLACE THE RATCHET FASTENERS IN THE
HOLES AND SNAP THEM IN PLACE
10)
NOTICE HOW ELECTRICAL CORD IS
FULLY EXTENDED THROUGH THE CABLE
MANAGEMENT TRAY AND OUT THE
END.
ADDITIONALLY, YOU MAY ALSO RUN
THE ELECTRICAL CORD THROUGH THE
LEG CABLE MANAGEMENT FOR FLOOR
POWER

YOUR TABLE IS NOW COMPLETE! ABOVE IS A
PICTURE OF THE IDEA ISLAND FULLY ASSEMBLED
MAKE SURE YOUR CASTERS ARE LOCKED AND
SECURED BEFORE FLIPPING THE TABLE OVER.
THIS WILL PREVENT ANY ADDITIONAL
MOVEMENT
USE CAUTION AND WITH ASSISTANCE FLIP TABLE
BACK OVER AND YOU ARE READY TO USE YOUR
NEW PRODUCT!