Cel-fi Quatra 4000 User manual

General Information

Safety Precautions

• Use this product indoors. It should not be used outdoors.

• This products is designed to be powered over Ethernet cabling.

• When installing the equipment, all the requirements of the

manufacturer and the referenced standards must be met.

• There are no user serviceable parts inside.

• CAUTION: Changes or modifications to this product not expressly

approved by Nextivity may void your right to operate the equipment.

Warranty

Nextivity Inc. provides a limited warranty for its products. For details,

please refer to www.cel-fi.com/warranty.

Limitation of Liability

In no event shall Nextivity, nor its directors, employees, agents,

suppliers or End Users, be liable under contract, tort, strict liability,

negligence or any other legal or equitable theory with respect to the

Products or any other subject matter of this Agreement (i) for any lost

profits, cost of procurement of substitute goods or services, or

special, indirect, incidental, punitive, or consequential damages of any

kind whatsoever or (ii) for any direct damages in excess of (in the

aggregate) the fees actually received by Nextivity from End User with

respect to the Products actually purchased and paid for.

See www.cel-fi.com for list of patents covering this product.

Electromagnetic Compatibility (EMC)

This equipment has been designed and tested to fulfill applicable

standards for:

• Radio frequency emission when installed according to the

instructions and used in its intended environment.

• Immunity to electrical and electromagnetic phenomena when

installed according to the instructions and used in its intended

environment.

USA

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV/IT technician for help.

Europe

QUATRA 4000

RANGE EXTENDER

Cel-Fi QUATRA 4000 Range Extender CEL-FI QUATRA ACCESSORY

STEP 2: Connect INPUT and OUTPUT cabling

• Extender power is provided by the cables from the Cel-Fi QUATRA

NETWORK UNIT.

• RJ45 LED #1 (solid amber) indicates power.

• RJ45 LED #2 will blink green during initialization, and will be solid

green when the Extender has passed self-test and is operating

normally.

• If both LEDs blink off periodically on a port, the port is resetting to

try and establish communications with the Cel-Fi QUATRA

NETWORK UNIT or Cel-Fi QUATRA COVERAGE UNIT it is

connected to. Check cables and connections if this occurs.

• If both INPUT LEDs are off, check the cable to the Cel-Fi QUATRA

NETWORK UNIT and that the NETWORK UNIT is powered up.

• If both OUTPUT LEDs are off, check the cable to the Cel-Fi QUATRA

COVERAGE UNIT.

• For further assistance, please consult your installer or contact

http://www.cel-fi.com/support.

Compliance Contact

In the event of a regulatory compliance issue, please contact Nextivity

Inc. at www.nextivityinc.com.

Note: Certifications are regional; not all products need or have the

same certifications. Please check the specific model number to

determine exactly which certifications it has.

Patents

This product is covered by Nextivity, Inc., US patents and patents

pending. Please refer to www.cel-fi.com for details.

Support

Should you require any assistance, please contact your Cel-Fi

QUATRA reseller. If your questions cannot be answered immediately,

your reseller will forward your queries through the appropriate

channels to ensure a rapid response. If you still need assistance visit:

http://www.cel-fi.com/support.

and Cel-Fi logos are registered trademarks of Nextivity Inc. All other trademarks or

registered trademarks listed belong to their respective owners. Designed by Nextivity

Inc in California. manual-quatra-4000-ext_19-1111

Installation

STEP 1: Locate and mount the Extender unit

• Input and Output port LEDs should be clearly visible.

• Allow adequate ventilation.

• Do not mount in direct sunlight, near heat sources, or in weather

exposed areas.

• The Cat 5e cables (or better) that connect the INPUT ports to the

Cel-Fi QUATRA NETWORK UNIT should not exceed 100 meters in

length.

• The Cat 5e cables that connect the OUTPUT port to the Cel-Fi

QUATRA COVERAGE UNIT should not exceed 100 meters in length.

USER MANUAL

The Cel-Fi QUATRA 4000 Range Extender is a Power over Ethernet

(PoE) device that extends the maximum distance between the Cel-Fi

QUATRA Network Unit and the Coverage Unit interconnect via cable

lengths up to 200 meters. Plug and play installation.

Cel-Fi QUATRA

NETWORK UNIT

Cel-Fi QUATRA

COVERAGE UNIT

Cat 5e cable

100 meter max

Output to

Cel-Fi QUATRA

COVERAGE UNIT

Input from

Cel-Fi QUATRA

NETWORK UNIT

INPUT

Cel-Fi QUATRA

NETWORK UNIT WITH

Cel-Fi QUATRA

RANGE EXTENDER

Cel-Fi QUATRA

COVERAGE UNIT

Cat 5e cable

100 meter max

Cat 5e cable

100 meter max

QUATRA 4000 RANGE EXTENDER

OVERVIEW

The Cel-Fi QUATRA Range Extender is designed solely for use with the

Cel-Fi QUATRA, and will not work with Cel-Fi QUATRA variants or

devices. Other extender products will not work with Cel-Fi QUATRA.

Only one (1) Extender may be used per Cel-Fi QUATRA Coverage Unit.

Mounting Holes

Cooling Fins

OUTPUT