Cellink NEO 8+S User manual

Note
The specifications listed in this manual are subject to change without the advanced notice.
This product is an external power supply, which is used to provide extended dash cam recording when the
vehicle is parked, without depleting or damaging the vehicle's battery. This manual outlines the basic
steps required to install and use the external battery.
EGEN
[ User’s Manual ]
8+s

●INPUT : The charging connector for connecting to the Cigar lighter socket, ACC Power andcontinuous
Power contacts in Fuse box.
●OUTPUT : The discharging connector for connecting to the dashcam.
●FIX/OFF/ADJ : The switch for adjusting the charge current.
▷FIX : It makes be possible to charge by only Minimum Charge Current of the product and not
possible control to the charge current with App.
▷OFF : System power off.
▷ADJ : It makes be possible to control the charge current between Min. to Max. with App.
●F/W : The connector for firmware up-date only(Technician Use Only)
●USB : The 5V output connector for charging a mobile product as a Smart phone.
●EXT.Battery : Connector for connecting to an extra battery such as CELLINK NEO EXT to add
the capacity.
●LED Display : Red - charging, Green - Fully charged, Blue - Bluetooth connected
When the switch is turned on, 3 LEDs are flashing for a while.
Name and Function of each terminal
General Specifications
Input Power
▷
When connected to the Cigar Lighter Socket : FIX only DC 12V~17V_Max. 6A
▷
When connected to the Fuse-box
ACC Power : ADJ only
DC 12V~17V_Max. 13.5A
Output Power
▷
Dashcam connector
DC 11.0V~14.2V_Max. 2A
▷
USB connector DC 5V_Max. 2A
Charging
Voltage & Current
FIX
▷
When connected to the Cigar Lighter
Socket
DC 14.2V_Max. 4.5A
ADJ
▷When connected to the Fuse Box ACC power
DC 14.2V_Max. 8.5A
Charging time
-
FIX : Fixed current
-ADJ : Adjusted current
FIX
▷
4.5A Charging : Approx. 100minutes
ADJ
▷
8.5A Charging : Approx. 50minutes
Switch Status
※ Set the charging current in APP when selecting the ADJ
Product Rating
▷
12.8V, 7500mA, 96Wh
Avilable Hours
▷
About 24Hours
※Based on 2CH dashcam within 4Wh power consumption.
Dim. and weight
▷
151(W)*207(L)*32.6(T)mm / Approx. 1.45kg
Battery used
▷
LiFePO4
FIX OFF ADJ

The CELLINK NEO8+S is designed to power your dashcam in Parking Mode
for extended periods of time without using your vehicle’s battery.
1. Bluetooth is built in, so the user can check the battery status in real time, including the time available
and estimated charging time through the smartphone APP.
2. Whenthe switch is set to ADJ, the smartphone APP allows the user to set the charging current of
the product from minimum to maximum current.
3. CELLINK NEO8+S offers the 2 types charging methodssuch as the vehicle’s cigar-lighterplug
and fuse-box ACC power connection.
4. Chargingstarts as soon as the vehicle starts the engine, if the ADJ on the switch is selected,
the users can change the charging current through the APP on the smartphone.
5. For better battery safety, a constant current constant. voltage charging circuit and a secondary
protection circuit are built in.
6. A microcontroller (MCU)is built in to control the current,voltage and voltage balance of the
battery, and the battery protection circuit module is built in for secondary protection to prevent
the over-charge, over-dischargeand over-current.
7. If you need more capacity, the CELLINK NEO EXT battery can easily make to increase the capacity
by connecting only the cables provided with the CELLINK NEO EXT.
8. The APP will put up a warning screen when the temperature inside the battery get to a certaintemperature,
and the system will automaticallystop to prevent overheatingif the product is in excess of 80°C.
9. The battery will be automatically cut off the current when the reverse voltage input or external
short-circuit of the product's connectors occur.
10.The
cycle life is improvedmore three times than the general Li-ion battery because of The lithium-
phosphate iron(LiFePO4)battery is used, and we guaranteeat least 1,500 cycles.
11.Compact
design makes possible to install in confinedspaces such as vehicle seat below.
CELLINK NEO8+S
Product Properties
3

Installation Guide(1)
※ Please set to the power-off before installation.
1. When connecting the product using the cigar-lighter socket Input cable.
OFF
FIX ADJ
CELLINK
NEO8+S
2. When connecting the product using the Fuse-box ACC Input cable.
CELLINK
NEO8+S

●Fuse box ACC contacts is supplied with power only when the engine is powered on.
1
) Withthe product’s power switch in the OFF position, connect
the Input(charging)cable for the fusebox and output cable to the
product’s cable connectors.
2) Open your vehicle’s fuse box, check the fuse standard, and select
the correctfuse holder between the included fuse holders.
3) Insert the input cable into the sleeve at the end of the fuse holder
cable, and then secure it by squeezing on the sleeve using
appropriate tools, such as pliers.
4) After removing the ACC contact-fuse of the less than 10A in the fuse
box, put the ACC contact-fuse provided with product in the fuse
holder, and then install the ACC fuse holder in the fuse box.
5) Find a bolt fixed on the vehicle’s and connect the ground (GND)
cable to the bolt.
▣
Make sure that the product is connectedproperly
1) Fix the productusing the providedvelcro tape on the car floor such as under the car seat.
2) Turn on the switch and check that the LEDs operate properly (Referto the LED Display table).
Note
The fuse box location in the vehicle may vary depending on the
manufacturer and model of your vehicle. For more information,
refer to your vehicle’s manual.
Caution
Insure that the fuse holder is installed into the continuous
power contact-fuse position in the fuse box.
!
Note
If the vehicle’s bolt is coated, remove the coating before
connecting the ground (GND) cable. The power may not be
supplied correctly due to the coating.
Installation Guide(2)

App download and installing
[App download]
1. Search for “CELLINK Neo Plus” and download the CELLINK Neo Plus App.
2. The Android users use the "Google Play" .
3. The iPhone users use the "App Store ".
[Before running the App]
Turn on the battery you purchased before running the downloaded app
Set to the power switch position is FIX or ADJ.
OFF
FIX ADJ
[How to Connect the App to the Bluetooth]
[Main Screen Description]
1. When
running the App on the smart phone, after loading, appear the
"SEARCHING DEVICE" and the searched Bluetooth device as shown on the left
picture.
2. click “N8PS” on
the searching list.
3. If you rescan, the connected device is displayed in blue and automatically
connected.
Caution
Check the code attached on the bottom of the purchased product and
click the same code on the smartphone to complete the installation.
1. The product's settings.
2 The product model name and the Bluetooth ID built-in to the product.
3. The Battery’s charging state and the internal temperature.
-The animation image is changed during charge and discharge.
-Displayed in red : during charge.
-Displayed in blue : during discharge and 100% full charge.
4. The present voltage and charging current to the battery.
5. The present voltage and discharge current from the battery.
6. The capacity of the product.
7. Estimated time to full charge(displayed "0" during discharge) at the
present input power level.
8. Available time as the current state(displayed "0" during charge) at the
present output power level.
Note
The App doesn't always need to be turned on. However, if the battery’s internal temperature is
high or input voltage is low, you can receive an alarm messege during the App is turned on.

①
●
You can enter the product setting screen by tapping the gear icon(①)on the
main screen. The password is requiredto enter the product setting screen.
The initial password is set to 1234.
●
You can set your own password to prevent other users from changing
the product settings at will .
- It is recommendedto change thepassword immediately after purchase.
- The “0000” cannot be used as a password and able to set within 0001~9999.
1. Padlock Icon : User’s own password setting.
-Your own password setting makes sure to prevent others from changing
the product settings.
2. Beep on/off : Setting status of battery sound. (initial value : on)
3. Charging Stop : The function to stop charging the battery.
4. Battery capacity : means the nominal capacity of the product.
5. Ext. Battery capacity : When you add an Extended battery pack like as
“CELLINK NEO EXT7”, enter the capacity of the added battery.
6. Charging current : You can change the charging current when you install
the battery to the fuse-box and the switch is selected to the ADJ.
Please enter the current within “4A~9A”.
[Warning to input voltage low]
[Warning to battery high temp]
[Product setting Screen]
●The warning screen will be displayed and stop
charging if the input voltage drops below 12V
to prevent the vehicle's damage.
●The warning screen will be displayed and stop
charging or discharging if the internal
temperature is more than 80℃ to prevent
the vehicle's and product's damage.
Note
If you have forgotten your password, please contact our Customer
Service Center.
[Product password setting]
①
②
④
⑤
⑥
③

How to add the capacity to CELLINK NEO8+S
1. If CELLINK NEO8+S needs more capacity, connect the extended
battery pack such as CELLINK NEO EXT7.
2. CELLINK NEO EXT battery is designed to add the capacity to
CELLINK NEO8+S easily.
▣
EXT. Battery Installation Guidance
1. Connect CELLINK NEO EXT" IN/OUT connector to the
EXT. Battery connector of CELLINK NEO8+S using the cable
provided with the CELLINK NEO EXT product.
2. After installation the EXT Battery product , enter the capacity
of the product connected to CELLINK NEO8+S on the App.
Caution
Make sure to connect the voltage of the extended battery is higher than the voltage of CELLINK
NEO8+S when connecting the extended battery to add the capacity to CELLINK NEO8+S.
It can make the functional problems in case of the extended battery’s voltage is lower.
!
Precautions on handling
Mishandling of CELLINK NEO8+S batteries can lead to degradation of performance and result inproblems
related to heating, ignition,explosionetc. As such, it is advisedto check the followingdetails.
1. When installing on vehicles, please use only the original cable providedwith the product.
2. When storing the battery, keep out of direct sunlight and do not store in a hightemperatureenvironment
such as inside the car in hot weather.
3. Do not place the battery in microwave oven or a place with high pressure.
4. Do not throw or give the battery any types of shocks.
5. Do not repair or remodelthe battery on your own.
6. Keep the battery out ofcontact of water or other liquid.
7. Do not disassemble, compress or drill a hole on the battery using sharp equipment.
8. Keep the battery out of contact of childrenor pets.
9. Whenthere is a strange smell during use, discontinue using the product and exchange with a new product.
10. When the battery is inflated during use, discontinue using the product and exchange with a new product.
11. Do not use the battery in a static environmentas it can affect the performanceof protection circuit
of the battery.
12. Keep the connection terminal of the charging cable of the battery out of contact withconducting elements.
13. Never use the product for anything else other than the power supply forDashcam.
Disposal guidance of battery
1. Don't throw away your batteries, separate them with recycled items.
2. Do not incinerate battery and put in the fire. Heat maycause explosion and fire.
3. Do isolate them each other when disposing the secondary batteries having different electrochemical systems.
4. Dispose of the batteryin discharged state to preventheat by short circuiting.
5. Disposal guidance of batteriesmay depend on each country and region,there for dispose batteries in
accordancewith the regulationsfor each countryand region.

Product Warranty
●
The warranty period of this product is 1 year from the purchase date.
●
If the product fails during normal and correct use within the warranty period, our service center will repair
the product free of charge.
●
Any disassembly, modification or alteration of the product will void the warranty.
●
The cost to repair or fix any malfunction or problem caused by incorrect usage during the warranty period
may be charged to the consumer.
●
The manufacturer shall not be responsible or liable for any loss or damage caused by incorrectly using
the product.
Customer Service
▣
Manufacturer : EGEN Inc.
▣
Address : 61, Dongtangiheung-ro, Dongtan-myeon, Hwasung-si, Gyeonggi-do,
Republic of Korea
▣
Customer Service Website : www.egens.co.kr