Central Pneumatic 34844 User manual

ASSEMBLYandOPERATINGINSTRUCTIONS
AIRBRUSHCOMPRESSOR
3491 Mission Oaks Blvd. / Camarillo, CA93011
Copyright © 1997 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
®

SPECIFICATIONS
SAVE THIS MANUAL
You will need the manual for the safety warnings and cautions, assembly instructions, operating
procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover. Keep both
this manual and your invoice in a safe, dry place for future reference.
SAFETY WARNING & CAUTIONS
WARNING: When using pneumatic equipment,basicsafety precautions should always befollowed
to reduce the risk of personal injury and hazards due to over pressurization.
READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit
locations.Don’t expose to rain.Keep work area well lit.Do not use electrically powered air
compressors in the presence of flammable gases or liquids.
3. KEEP CHILDREN AWAY. Children must never be allowed in the work area.Do not let
them handle machines, tools, or hoses.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location
to inhibit rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for
which it was intended. Do not use inappropriate attachments in an attempt to exceed the
tool’s capacities.
6. USETHERIGHTTOOLFORTHEJOB.Donotattempttoforceasmalltoolorattachment
to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not
intended.
7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in
movingparts.Non-skidfootwearisrecommended.Wear restrictive hair coveringto contain
long hair.
Air Pressure Rating 30PSI
Air Production 2CFM
Motor 1/8 HP, 115V, .6 amps
AirOutlet 1/8" NPT
Page 2 -- SKU: 34844 REV 10/04

8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash
goggleswhenworkingwithchemicals.AlwayswearANSI approved impact safety goggles
atother times.Wear a full face shield if youare producingmetal filings or wood chips.Wear
anANSI approveddustmask orrespiratorwhen workingaroundmetal, wood,andchemical
dusts and mists.
9. DO NOT ABUSETHE POWER CORD. Do not yankcompressor’s cord to disconnect it
from the receptacle. Do not carry tools by the cord.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach
over or across running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
compressor’s cord periodically and, if damaged, have them repaired by an authorized
technician. Inspect all hoses for leaks prior to use.The handles must be kept clean, dry,
and free from oil and grease at all times.
12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys
andadjusting wrenchesareremoved fromthetool or machineworksurface beforeplugging
it in.
13. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your finger on the
trigger, whether it is connected to the compressor or not.
14. STAY ALERT. Watch what you are doing;use common sense.Do not operate any tool
when you are tired.
15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged
shouldbecarefullycheckedtodeterminethat itwill operateproperly andperform itsintended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures;and anyother condition that mayaffect proper operation.Anypart that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if any
switch does not turn on and off properly.
16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
17. DO NOT OPERATETOOL IF UNDERTHE INFLUENCE OF ALCOHOL OR DRUGS.
Readwarning labels onprescriptionstodetermine if yourjudgmentor reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the
compressor.Do not allow compressor to sit pressurized for longer than one hour.
19. Make sure that regulator is set at least 10 PSI lower than the lowest rated piece of
equipment you are using.
Page 3 -- SKU: 34844

VOLTAGE WARNING
Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage
suppliedis about the same asthat specified on the nameplateof the tool. If one says 120V andthe
othersays110Vthenthere will be nocomplications.Never try to pluga110V tool into a220Voutlet,
or the other way around. The plug and outlet have completely different shapes. This is because a
power source with a voltage greater than that specified on the tool can result in a SERIOUS
INJURY to the user— as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL.
Using a power source with voltage (110V) less than the nameplate rating (220V) is harmful to the
motor.
EXTENSION CORDS
If your tool is double insulated and has a two-prong plug, you may use either a two- or
three-prong extension cord. If your tool has a grounded, three-prong plug, you must use a three-
prong extension cord with three-prong receptacles. Only use rounded jacket extension cords,
preferablylisted by the UnderwritersLaboratories (UL). Make surethe cord is ratedfor outdoor use
if you plan on using the tool outside; if you plan on indoor use, you may also use an outdoor rated
cord. Extension cords rated for outdoor use have the letters “WA” on the cord jacket.
Theextension cord must have aminimum wire size depending on the amperage ofthe tool
and the length of the extension cord. This size is signified by its AWG (American Wire Gauge)
rating; the smaller the gauge, the greater the cable’s capacity. If you are using two or more cords,
the total length of the combined cords must be used to determine the minimumAWG rating. Each
of the cords used must meet this rating.
The chart below is used to determine the rating required according to the length of the
cord(s). The amps of your tool are found either in this manual, or on the nameplate of the tool.
AMP
RATING 25 50 75 100 125 150 175 200
0-10.0 18 18 16 16 14 14 12 12
10.1-13.0 16 16 14 14 14 12 12 12
13.1-15 14 14 12 12 12 12 12 __
15.1-18 12 12 12 12 12 12 __ __
Always inspect extension cords for any damage. If there are any loose, frayed or exposed wires,
damaged insulation, or defective connections, replace the cord. Harbor Freight Tools can supply
UL listed and outdoor rated cords in multipleAWG ratings if needed.
TOTAL EXTENSION CORD(S) LENGTH IN FEET
A
W
G
Page 4 -- SKU: 34844

UNPACKING
When unpacking your Air Brush Compressor, check the items against the list below. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual.
Item# Description Qty
N/A Air Compressor Assembly 1
N/A BrassAdapter Fitting 1
7 AirConduit 1
ASSEMBLY
Step 1:Remove the contents of the box and place on a clear work area.
Step 2:Place the JET PEN HOLDER (#10) onto the end of the HANDLE (#9) as shown in
Figure1.
Figure 1 — Placing the Jet Pen Holder
Page 5 -- SKU: 34844

Step 3:Remove the Brass Fitting from the Air Outlet Nipple on the Air Brush Compressor
as shown in Figure 2.
Figure 2 — Attaching the Air Conduit
Step 4:Place the Brass Fitting removed in Step 3 onto the bare end of the AIR CONDUIT
(#7). Makesurethethreads oftheBrassFitting face towardtheend of theAIRCONDUIT.
Step5:Placethe bare end of the AIRCONDUITovertheendof the Air Outlet Nipple. Make
sure the AIR CONDUIT is pressed over the ridge in the Air Outlet Nipple as shown in
Figure 2.
Step6:ThreadtheBrass FittingfromStep 4onto thethreadsof theAir OutletNipple. Tighten
snuggly, but do not over tighten as you may damage the AIR CONDUIT.
Your Air Brush Compressor is ready for use.
OPERATION
Step 1:Connect your air brush to the Brass Fitting at the end of the AIR CONDUIT (#7).
Tighten as appropriate.
Step 2:Plug the Power Cord into an appropriate outlet.
Step 3:To operate the Air Brush Compressor, flip the Switch to the ON or “l” position.
Page 6 -- SKU: 34844

MAINTENANCE
While operating theAir Brush Compressor, make sure the AIR INLET (#8) and the Motor Fan are
free of obstructions.
Periodicallyremove theAIRINLETfrom theAirBrush Compressor. TheAIRINLET’S foam rubber
serves as a filter for purifying the air. Make sure it is clean at all times.
There are no user-serviceable parts in yourAir Brush Compressor. If you need service performed
on your Compressor, please return it to Harbor Freight Tools.
DIAGRAM
PARTS LIST
Item# Description Qty Item# Description Qty
2 Compressor 1 9 Handle 1
7 AirConduit 1 10 Jet Pen Holder 1
8 AirInlet 1
Page 7 -- SKU: 34844