Centre Point CP-ISP10 User manual

CP-ISP10
INSPECTION CAMERA
INSTRUCTION MANUAL

2
Read the following safety instructions
before attempting to operate this
product.
Keep these instructions in a safe place
for future reference.
SAVE ALL WARNINGS AND
INSTRUCTIONS FOR FUTURE
REFERENCE.
WARNING!
Read and understand all
instructions.
• Use only accessories that are
recommended for your model.
• Tool service must be performed
only by qualified repair personnel.
Repairs, service or maintenance
performed by unqualified personnel
will void the warranty. Only approved
and authorised service technicians
can carry out warranty repairs.
• Position the tool securely on a
level surface. Damage to the tool
or serious injury could result if the
tool falls.
!
Safety

3
WARNING!
Do not disassemble the tool
There are no user serviceable parts
inside. Disassembling the tool will void
all warranties on the product. Do not
modify the product in any way.
!

4
Please ensure the following items are
included with your inspection camera.
If anything is missing please contact
your retailer.
Centre Point CP-ISP10
Rubber cap
Item Checklist

5
Camera cable
Magnet
Hook
Mirror

6
Inspection Camera
Overview

7
LCD screen
Battery compartment
Power
Power indicator
Camera connection point
Low battery indicator
Screen rotation
Contrast control
Brightness control

8
POWER SUPPLY
• The CP-ISP10 is powered by four
AA batteries
Battery replacement
• Remove the battery door cover.
• Remove the batteries from the
battery case.
• Insert the new batteries according
to polarity and insert the battery
case.
• Replace the battery door cover.
Using Your
Inspection Camera

9
Open the battery door
Remove the battery compartment
Insert the batteries according to polarity

10
Align the keyed tube with the
slot in the handle
Push and rotate clockwise to
secure in place
SETTING UP
Attaching the camera cable
• To attach the camera cable to the
monitor, make sure the keyed end
of the tube is aligned with the slot in
the handle.
• Push together with slight force and
twist clockwise to connect securely
in place.
Using Your Inspection Camera

11
Using Your Inspection Camera
(continued)
Place the hook into the hole on the
camera head
Place the rubber cap around the
camera head and hook
Attaching the accessories
• To install the mirror, hook or magnet
place the hooked end into the hole
at the camera head.
• Place the rubber cap around the
camera head and hook to secure
into place.

12
OPERATION
• Press the power switch to turn the
camera on. The power indicator
will light and the LCD screen will
become active.
• If the image on screen is unclear,
adjust the brightness or contrast by
pressing the brightness control or
contrast control buttons on the unit.
• To rotate the orientation of the image
displayed, press the screen rotation
button to cycle through each angle.
• Maneuver and adjust the camera
cable into position.
i
i
The camera cable can be bent
into numerous shapes that can
help you inspect areas that are
normally out of view.
To avoid damage to the camera
cable it is recommended not
to bend the cable at an angle
greater than 90°.
Using Your Inspection Camera

13
WARNING! Do not immerse the
monitor into water. Only the lens
and tube are water resistant once
the unit is fully assembled.
!
(continued)
Place the camera head in the
desired location

14
• Whenever possible, store the
instrument in a dry, shady location.
• Clean the instrument with a dry, soft
cloth after use in dusty, damp or wet
conditions before storing.
• Smudges and fingerprints may be
removed with a damp tissue or a
soft, lint-free cloth.
• Remove the alkaline batteries from
the tool before storing for extended
periods.
i
Only the lens and camera
cable are water resistant. Do
not expose the monitor to wet
conditions.
Care & Maintenance

15
Warranty
The Centre Point CP-ISP10 comes with a 3
(three) year warranty.
1. The warranty period for your tool is 3
years from the date of purchase.
2. To claim under the warranty, the
date of purchase of the tool must be
documented by an invoice/receipt.
3. Damage and general wear and tear
is not covered by warranty.
AUSTRALIA
“Our goods come with guarantees
that cannot be excluded under the
Australian Consumer Law. You are
entitled to a replacement or refund for
a major failure and for compensation
for any other reasonably foreseeable
loss or damage. You are also entitled
to have the goods repaired or replaced
if the goods fail to be of acceptable
quality and the failure does not amount
to a major failure.”
For more information please visit
consumerlaw.gov.au
NEW ZEALAND
For more information please visit
consumerprotection.govt.nz

16
To assist you with any queries or
technical questions please contact
customer support
Australia: 1300 658 338
New Zealand: 0800 367 527
United Kingdom: 0808 189 1152
Customer Support

17
Specifications
Specifications Centre Point
CP-ISP10
Product code 400060
Warranty 3 Years
Resolution 640 x 480px
Display 2.4” TFT LCD
colour
Camera lens width 9mm (diameter)
Night vision range 0.5m
Battery type 4x AA alkaline
batteries
IP rating 67
Weight (kg) 0.4
Dimensions (mm) 201 x 83 x 59

18
Notes

19

www.spoton.com.au