CertainTeed NO-COAT PRO User manual

Operating Instructions
CertainTeed
TO LOAD NO-COAT® PRO CORNER INTO THE
NO-COAT® PRO MACHINE:
1. Push in perforated section above finger hole.
2. Tear out perforated large end panel and remove.
3. Using finger holes, remove perforated panels on
both sides of the box.
4. Lift box with perforated end panel facing machine, and
mount over spindle.
5. Box should fit snugly against spindle arm, resting on the spindle
and corner pin.
6. On opposite box side, make sure box sits on spindle and is secured
in place by spindle cap.
7. Pull end of NO-COAT PRO Corner out of box and slide under
guide pin.
8. Feed NO-COAT PRO Corner through open slot into feed rollers
using the feed knob. Make sure center groove in product lines
up with centering roller. Turn feed knob until product stops
against inside cutter blade.
9. To remove or adjust position of NO-COAT PRO Corner, push
down on feed release lever.
Spindle Arm
Spindle Arm
Corner Pin
Top View
Spindle
Spindle
Spindle Cap
DO NOT tear or
remove this area
of box!
Front
Back
Guide
Feed Rollers
Feed Knob
Feed
Release
Lever
Centering
Roller
Guide Pin
Turn Feed Knob
counter-clockwise only!

CertainTeed Corporation
CEILINGS • DECKING • FENCE • GYPSUM • INSULATION • RAILING • ROOFING • SIDING • TRIM
2424 Lakeshore Rd. West, Mississauga, ON L5J 1K4
Professional: 800-233-8990 Consumer: 800-782-8777 certainteed.ca
© 05-2019 CertainTeed Canada, Inc. CTG-7070
SETTING FOR OUTSIDE OR INSIDE CORNER
For an outside corner:
1. Rotate the folder handle away from you until the folder
handle rests against the stop pin in the OUT position.
2. Locate the hopper with the tapered feet in the far set of
locating holes.
For an inside corner:
1. Rotate the folder handle toward you until the folder handle
rests against the stop pin in the IN position.
2. Locate the hopper with the tapered feet in the near set of
locating holes.
LANGUAGE
To set the language of the display to English, Spanish or French:
1. Press MENU and select “2 - EN/ES/FR”
2. Select language.
RUNNING CORNERS
Enter “run mode”:
1. Make certain the product is loaded properly and the product
box is touching the end of the NO-COAT PRO.
2. Make certain the folder and hopper are both set for the
desired corner (inside or outside).
3. Press RUN or the remote button to enter “run mode” and
dispense the first corner on the list.
4. To pause the corner output, press STOP or the remote button
during output - press RUN or the remote button to resume.
5. Press RUN or the remote button to dispense the next corner
on the list.
PULLING CORNERS OUT OF THE NO-COAT PRO
1. Support the corner as it comes out of the NO-COAT PRO.
Wait to pull out the product until you hear the NO-COAT PRO
cut the corner — if you pull the corner before the cutter fires,
it may cause length errors.
2. After the NO-COAT PRO cuts the corner, be certain to pull
the corner from the NO-COAT PRO smoothly and at a
consistent speed to ensure optimal joint compound coverage
on the corner. Pulling the corner out too rapidly may result in
gaps in joint compound coverage. Also, be careful to pull
the corner straight
out and level, to
avoid deforming
the corner.
3. Do not run another
corner until you have
removed the previous
corner from the
NO-COAT PRO.
Exit “run mode”
1. Press STOP to exit
“run mode” in order
to edit the corner data, edit the list, recall a stored list, etc.
End of roll
In the event that the end of a roll is reached while dispensing a
corner the NO-COAT PRO will stop dispensing and not cut.
1. Remove the current corner from the NO-COAT PRO.
DO NOT PRESS CUT BEFORE REMOVING THE CORNER —
pressing cut before removing the corner may cause a small
piece of product to remain in the cutter which may jam the
NO-COAT PRO.
2. Press CUT to reset the NO-COAT PRO.
3. Load a new roll of product, making certain that the
product stops against the cutter blade (to ensure proper
corner length).
4. Press RUN to repeat the corner or press ENTER to skip
to the next corner.
On/O
Switch
Scroll Arrows
Inside
Corner
Position
Outside
Corner
Position
Folder
Handle
Inside
Corner
Holes
Outside
Corner
Holes
Stop Pin