Ceyear 4024 Series User manual

4024 Series
Spectrum Analyzer
Quick Start Guide

Foreword
Thank you for choosing 4024
Spectrum Analyzer developed
and produced by China
Electronics Technology
Instruments Co., Ltd.
We take customer demands as
our own duty, providing you
high-quality measuring
instrument and the best after-
sales service. We persist with
"superior quality and
considerate service", and are
committed to offering
satisfactory products and
service for our clients.
Version
A.7 2018.09
China Electronics Technology
Instruments Co., Ltd.
Statement
The information contained in
this User Manual is subject to
change without prior notice.
China Electronics Technology
Instruments Co., Ltd. reserves
the right of final interpretation
for the content and terms used
in this Manual.
China Electronics Technology
Instruments Co., Ltd. owns the
copyright of this Manual.
Without prior approval of
China Electronics Technology
Instruments Co., Ltd., any unit
or individual shall not modify
or tamper the content of this
Manual, or reproduce or
transmit this Manual for profit.
Otherwise, China Electronics
Technology Instruments Co.,
Ltd. shall reserve the right to
investigate legal liability
against the copyright infringer.
Product Quality
Assurance
The warranty period of the
product is 18 months from the
date of delivery. We shall
repair or replace the damaged
part as the case may be within
warranty period. For this
purpose, the user shall return
the product to the
manufacturer and prepay the
mailing expense which shall
be returned to the user by the
manufacturer together with the
product after maintenance.
Product Quality
Certificate
The product meets the
indicator requirements of the
manual at the time of delivery.
Calibration and measurement
are completed by the
measuring organization with
qualifications specified by the
state, and relevant data are
provided for reference.
Quality/Environment
Management
Research, development,
manufacturing and testing of
the product comply with the
requirements of the quality and
environmental management
system. China Electronics
Technology Instruments Co.,
Ltd. has passed the ISO 9001
and ISO 14001 certifications.
Precautions
“Warning” indicates danger. It
reminds the user to pay
attention to a certain operation
process, operation method or
similar situations.
Noncompliance with the rules
or improper operation may
result in personal injuries. You
shall fully understand and
meet all the conditions in the
warning before proceeding to
the next step.
Warning
!
!

“Attention” indicates
important prompts and no
danger. It reminds the user to
pay attention to a certain
operation process, operation
method or similar situations.
Noncompliance with the rules
or improper operations may
result in damage to the
instrument or loss of important
data. You shall fully
understand and meet all the
conditions in the caution
before proceeding to the next
step.
Caution

Quick Start Guide of 4024 Spectrum Analyzer
Table of Contents
CHAPTER 1 MANUAL GUIDE...............................................................................................................1
CHAPTER 2 PREPARATION FOR USE ...................................................................................................2
2.1 PRE-OPERATION PREPARATION .......................................................................................................2
2.2 DESCRIPTION OF START FOR USE .....................................................................................................4
2.3 OVERVIEW OF FRONT PANEL ..........................................................................................................5
2.4 OVERVIEW OF OPERATION INTERFACE ..............................................................................................7
2.5 OVERVIEW OF TOP PANEL .............................................................................................................. 8
2.6 BATTERY INSTALLATION OR REPLACEMENT ......................................................................................10
CHAPTER 3 TYPICAL APPLICATION ................................................................................................... 12
3.1 BASIC SIGNAL MEASUREMENT ...................................................................................................... 12
3.2 HOW TO IMPROVE FREQUENCY MEASUREMENT ACCURACY ................................................................16
3.3 HOW TO MEASURE SMALL SIGNALS................................................................................................17
3.4 HOW TO IDENTIFY SIGNAL WITH CLOSELY SPACED FREQUENCY.............................................................23
CHAPTER 4 HELP ..............................................................................................................................27
4.1 BASIC INSPECTIONS ....................................................................................................................27
4.2. HELP INFORMATION ..................................................................................................................28
4.3 REPAIR .................................................................................................................................... 29
ANNEX I: TECHNICAL INDEX ............................................................................................................. 30
ANNEX II: LIST OF ACCESSORIES/OPTIONS .......................................................................................33

Quick Start Guide of 4024 Spectrum Analyzer
1
Chapter 1 Manual Guide
This Manual describes the structure and use of 4024 Spectrum Analyzer (hereinafter referred to as
4024 or Spectrum Analyzer) in an all-around and three- dimensional manner from aspects of
instrument panel, power supply, start to use, typical applications and after-sales help. By reading
this Manual, you will have an overall understanding of 4024 and quickly master the basic
operations of this device in a systematic manner. For the convenience of operation, please
carefully read the manual before operating the instrument, and properly operating it according to
the guidance in the manual.
Chapters in the Quick Use Guide of 4024 Spectrum Analyzer are:
Preparation for use
This chapter introduces preparations before use, start to use, panel introduction and battery
replacement. By reading this chapter, you will gain the perceptual knowledge of 4024 as a whole
and make preliminary preparations for correct and safe operation of this device.
Typical application
This chapter explains basic measurement methods of 4024 and operating steps of basic
measurement functions in details through test instances on how to distinguish closely spaced
signals, how to improve frequency measurement accuracy and how to measure small signals. In
addition, this chapter also briefly describes the skills used in tests. By reading this chapter, you
can use 4024 to complete certain typical tests independently.
Help
This chapter consists of after-sales repair and its procedures with the emphasis on problem solving,
maintenance and repair of this device during use.

Quick Start Guide of 4024 Spectrum Analyzer
2
Chapter 2 Preparation for use
4024 Spectrum Analyzer series is characterized by wide operating frequency band, high
performance index, fast sweeping, multiple test functions and easy operation. In terms of
performance index, this series has good average noise level, phase noise, fast sweep speed and
multiple measurement functions. Adopting the 8.4-inch integrated liquid crystal and capacitive
touchscreen and portable structure with small volume and light weight, this series features flexible
power supply and is particularly suitable for field use. This chapter emphatically introduces the
test environment, power supply, structure and battery replacement of this device.
2.1 Pre-operation preparation
This section describes the precautions for the first use of 4024 Spectrum Analyzer for the first
time. The safety of 4024 meets the requirements in GJB3947A-2009. Please carefully read the
following safety precautions before use in order to avoid any damage to the device or unnecessary
personal injury.
To prevent damage to the instrument and avoid electric shock, fire and
personal injury:
Do not open this device without authorization;
Do not disassemble or modify any part which is not described in this
manual. Any disassembly without authorization may result in reduction of
electromagnetic shielding performance or damage to the parts inside the
device, thus comprising product reliability. We shall not offer free repair
service to any product which is disassembled without authorization even if
the product is still within warranty period.
2.1.1 Environmental Requirements
In order to ensure the longer service life of 4024 and the effectiveness and accuracy of
measurement, tests should be done under the following conditions.
1. Temperature range:
Storage temperature range: -40℃~+70℃
Operating temperature range: -10℃~+50℃
Warning
!
!

Quick Start Guide of 4024 Spectrum Analyzer
3
Operating temperature range of power supply by Li-ion battery：0℃～+45℃
2. Low pressure
Low air pressure (altitude): 0~4600m
2.1.2 Power supply requirements
Three power supply forms are supported by 4024:
1. AC power supply and power supply with adapter
The accompanying AC-DC adapter must be used for AC power supply. The input power supply of
the adapter is 100~240V, 50/60Hz AC.
When transported and carried in a backpack, please do not connect the AC-DC adapter to the
device to avoided overheating. The AC-DC adapter has a wide range of voltage input. When in
use, please make sure the power supply voltage is within the scope specified in Table 2.1.
Table 2.1 Power supply requirements
Power supply parameter
Applicable range
Input voltage
Rated input currency
Work frequency
Output Voltage/Current
100V~240VAC
1.7A
50/60Hz
15.0V/4.0A
The working voltage and frequency ranges are subject to the parameters
provided on the nameplate of the power adapter.
2. DC power supply
Voltage: 15V
As the battery storage temperature range is -20℃to 60℃, the battery
must not work continuously in a long time at high temperature, so as to
avoid risks arising from high temperature. It is recommended to use the
adapter to supply power.
Caution
Warning
!
!

Quick Start Guide of 4024 Spectrum Analyzer
4
Current: 3A (min.)
3. Power supply with built-in battery
4024 can be powered by rechargeable li-ion battery. The battery will discharge if it is not used for
a long time. Therefore, the battery must be recharged before use. Please refer to Section 2.6 for
details about battery use. Basic parameters of accompanying battery are as follows:
Nominal voltage: 10.8V
Nominal capacity: 7,800mAh
The rechargeable battery must not be exposed to fire or high-temperature
environments (above 70℃), or placed in fresh water or salt water, or made
wet. It must be kept away from children.
The rechargeable battery is reusable and should be stored in proper
container to avoid short circuit. Heavy metals such as nickel and
chromium in the battery can pollute natural environment. Waste battery
shall not be discarded but shall be put into a special battery recycle box.
2.1.3 Electrostatic protection (ESD)
Attention should be paid to electrostatic protection when using the device. If condition permits,
the following electrostatic protection measures may be taken:
1. Before connecting the power cable to the device for test, make sure the central conductor of the
power cable is grounded. This can be realized through the following steps: Connect a short-
circuiter to one end of the cable to realize short circuit between the central conductor and outer
conductor of the cable. When wearing a anti-static wrist band, hold on to the casing of the cable
connector and connect the casing to the other end of the cable before removing the short-circuiter.
2. The operator should be grounded before cleaning or checking the test port of the device or
connection. This can be realized by holding on to the metal casing of grounded device or the
casing of test cable connector.
2.2 Description of start for use
Before powering 4024, please check the power supply equipment as per “Power supply
requirements” in Section 2.1.2. Power-on test can only be carried out after confirmation.
Caution

Quick Start Guide of 4024 Spectrum Analyzer
5
Press the Power ON/OFF (【】key) for about 3 seconds, a beep can be heard. Then, release
the ON/OFF key and the device will enter host program after about 30 seconds. To ensure the
stability of performance indexes of parts inside the device in order to achieve better test results, a
30-minute warming period is recommended before measurement.
2.3 Overview of front panel
This section describes the front panel of 4024 in details. Fig. 2.1 shows the front panel of 4024.
Touchscreen
display area
Power button and
indicator
Function key Reset key
Label display
area
Numeric
keypad
Loudspeaker
Photosensitive
hole
RF input
10MHz reference input/output
IF Output
GPS antenna
Trigger input
Fig. 2.1 Front panel of 4024 SpectrumAnalyzer
2.3.1 Power key and indicator
Power key and the indicator are located at the lower left of the front panel. The power indicator is
inside the yellow power key. The indicator for power off is yellow and that for power on is green.
The correlation between color of the indicator and physical status of the device is shown in the
table below.

Quick Start Guide of 4024 Spectrum Analyzer
6
Table 2.2 Description of indicator status
Instrumen
t status
Indicator
status
Physical status of the Spectrum Analyzer
Power off
Off
a) battery installed, power not connected.
b) battery not installed, power not connected.
Yellow
normally on
a) battery not installed, power connected.
b) battery installed and full, power connected.
Yellow
flickering
Battery installed but not full, power connected.
Power on
Status
Green
normally on
a) battery not installed, power connected.
b) battery installed and full, power connected.
c) battery installed, power not connected.
Green
flickering
Battery installed but not full, power connected.
2.3.2 Functional key zone
Commonly-used functional keys are described as follows:
【Freq】: Set the scope of frequency measured, frequency step, signal standard, etc.
【Ampt】: Set the amplitude of measurement results displayed, including display format,
display scale and control of pre-amplifier.
【BW】: Set the resolution bandwidth, video bandwidth, detector type, average value and
other measurement parameters.
【Marker】: Enable function menu related to the marker. When enabled, the marker can be
operated by dragging, clicking or other touch modes.
【Peak】: Enable the peak search function.
【Mode】: Select the operating mode of the device, including spectrum analyzer, interference
analyzer, AM-FM-PM analyzer, power meter, channel scanner and other modes.
2.3.3 Preset button
Preset or reboot the system to restore to default initial state. Preset can be realized by pressing and
releasing this key.
2.3.4 Photosensitive hole
This hole can sense the intensity of external light for auto adjustment of liquid crystal brightness.
2.3.5 Numeric keypad

Quick Start Guide of 4024 Spectrum Analyzer
7
Numeric keys: You can input corresponding value of the parameter selected with numerical
keys at front panel and input the data after selecting corresponding unit at soft menu.
【•】: Input the decimal point for decimal value when entering a decimal value with a
decimal point.
【+/-】: Positive/negative sign: before inputting a numerical value, you can use this key to
input a positive or negative value.
【↑】and 【↓】You can use these keys to control the step up or down or to select current
item.
【Cancel】: You can use this key to exit from any functional operation without changing
current parameter. Cancel the active function, and exit the number operation and file dialog
box.
【Backspace】You can use this key to remove a character before the marker in the input area.
【Enter】: You can use this key to receive data in default unit in the input area.
Knob: You can use this knob to move the marker and change the value of current parameter.
This knob is generally used for fine tuning the parameter to the optimal value.
2.3.6 Loudspeaker
4024 is equipped with a loudspeaker. Please keep the loudspeaker hole clean to avoid
compromising the sound effect.
2.3.7 Label display area
This area displays the model, frequency range, label and name of this 4024 Spectrum Analyzer.
2.4 Overview of operation interface
4024 adopts the design of 8.4-inch integrated liquid crystal and capacitive touchscreen. The
operation interface is shown in Fig. 2.2.

Quick Start Guide of 4024 Spectrum Analyzer
8
Time and date Signal standard and cursor
Left information display Bottom information display area
Trace display area
Software menu display area Bottom function key area
GPS info Power identification
Title
Fig. 2.2 Operation interface of 4024 Spectrum Analyzer
2.5 Overview of top panel
The top panel of 4024 is shown in Fig. 2.3 and it consists of a power interface, a digital interface
and a test port.
USB
GPS
Mini USB
External power
supply
RF In
LAN
interface
SD card slot
Headset
jack
10MHz In/Out
IF Out
Trig In
RF Out
Fig. 2.3 Top panel of 4024 Spectrum Analyzer

Quick Start Guide of 4024 Spectrum Analyzer
9
2.5.1 Power interface
The power interface of the device is for powering the device through DC output of AC-DC
adapter or through external DC power source. The conductor inside the external power interface is
positive and the external conductor is grounded.
2.5.2 Test port
1. RF Input port: This port is for inputting tested signal. The test signal input port of 4024 is 50Ω.
4GHz, 6.5GHz, 9GHz, 20GHz and 26.5GHz models use N type female port and 32GHz and
44GHz models use 2.4mm male port.
2. RF Output port: This port is for signal output. 50Ω impedance, N-type female port, provided
only when customers need the tracking generator option.
3. 10MHz Input / Output port: This port is for connecting 10MHz signal of other devices as the
reference signal of the analyzer. It can also be used for outputting the internal 10MHz reference
signal for other devices.
4. IF Output port: Under zero span, this port can be used for outputting the IF signals for other
devices through software configuration.
5. Trigger input port: External trigger mode can be set for 4024. The scope of trigger source must
be -5V~+5V when connecting the external trigger source to the trigger input port of the Spectrum
Analyzer. Rising edge trigger or fall edge trigger can be set by the software.
6. GPS antenna port: This port can be used for connecting GPS antenna device for locating current
position of the Spectrum Analyzer.
To better protect the SpectrumAnalyzer, some identifiers are provided at
the test port of the device. The user must pay attention to the content on
these identifiers when using this device, in order to avoid any permanent
damage to the device.
Please refer to Section 2.5.4 for detailed explanation of symbols in the
figure.
2.5.3 Digital interfaces
Warning
!
!

Quick Start Guide of 4024 Spectrum Analyzer
10
1. Mini USB interface: This interface is used for connecting external PC which realizes program
control or data transmission for 4024 through program control commands or function library.
Equipment drive should be installed for connecting the device to PC
through USB interface for the first time.
2. USB A type interface: This interface is used for connecting USB peripheral equipment, such as
USB storage device, USB power detector.
3. LAN (network) interface: This interface is a 10/100Mbps network interface through which a PC
can be connected to the device through a network cable. PC can realize program control or data
transmission for 4024 through program control commands or function library.
4. SD card slot: This Micro SD card slot can be used to extend the storage space of the device.
5. Headset jack: This is a standard headset jack for 3.5mm/3 line for audio output of FM/AM/SSB
demodulation. When a headset is not connected to this jack, the audio output will be realized
through the loudspeaker of the device. When a headset is connected to this jack, audio output will
be automatically switched from the loudspeaker to the headset.
2.5.4 Device symbols
Device symbols indicated in the figure below indicate that the maximum power of RF IN and the
maximum input DC level. When the device is in operation, the user is not allowed to connect
signal exceeding this range to the port. Otherwise, the device may be destroyed!
2.6 Battery installation or replacement
4024 accompanies with a large-capacity rechargeable Li-ion battery with a battery life of 2.5
hours. For field test for long period, it is recommended to purchase a battery of same mode as a
standby battery.
To guarantee the longer service life of the battery, the battery should be
removed from battery holder during the transportation and long-time
storage, and try not to make the battery power less than 5%, otherwise the
battery may not be able to charge.
Installation or replacement of battery can be carried out by reference to Fig. 2.4 for battery
installation or replacement of 4024.
Caution
Caution

Quick Start Guide of 4024 Spectrum Analyzer
11
Remove the battery cover Remove the battery
Install the battery cover Insert the battery
Fig. 2.4 Install or replace the battery

Quick Start Guide of 4024 Spectrum Analyzer
12
Chapter 3 Typical application
Several working modes are available in 4024, including spectrum analyzer, interference analyzer
(option), AM-FM-PM analyzer (option), power meter (option) and channel scanner (option).
Several intelligent measurement functions are provided for each working mode. This chapter
mainly describes basic tests under spectrum analyzer mode. For detailed operation of each
optional mode, please refer to the User Manual of 4024 Spectrum Analyzer.
In this Guide, keys on the front panel are shown in the form of 【XXX】,
in which XXX is the name of the key. Bottom buttons on the touchscreen
are shown in the form of [XXX], in which XXX is the name of the key;
buttons on the right menu are shown in the form of [XXX], in which XXX
is the name of menu.
3.1 Basic signal measurement
Basic measurements include marking the frequency and amplitude of signal by a marker on the
screen of the Spectrum Analyzer. Input signals can be measured by following the steps below and
current measurement results can be saved using the file menu:
a) Set center frequency
Set the frequency of external signal generator as 1GHz. Set the center frequency of the Spectrum
Analyzer. Press 【Freq】, select [Center Freq] and set the center frequency as 1GHz. Or you can
directly input [1] [GHz] using the keys in numerical keypad on the front panel. These numerical
keys can be used for setting the exact value of current parameter. The value of center frequency
can also be changed by the step key and knob, as shown in Fig. 3.1.
Caution

Quick Start Guide of 4024 Spectrum Analyzer
13
Fig. 3.1 Center frequency is 1GHz
b) Set span
Press 【Freq】→[Span]. Please note if the span is shown in the active function area in order to
confirm currently activated parameter. To reduce the span to, for example, 10MHz, you can input
[1] [0] using the numerical keypad and select the unit as [MHz], or you can use 【↓】key to
reduce to this value by step (the numerical keys and step keys can be used for changing the value
of current parameter). The result is shown in Fig. 3.2. Attention should be paid to check if the
resolution bandwidth and the video bandwidth are adaptable to the span as they will be
automatically adjusted to a proper value based on the given span value. The sweep time is also
adaptable.

Quick Start Guide of 4024 Spectrum Analyzer
14
Fig. 3.2 The center frequency is 1GHz and the span is 10MHz
c) Set the sweep time
Press 【Sweep】and select [Sweep Time Auto Man] soft key. This soft key can be used for
setting the control mode of sweep time as auto control or manual control. The underlined item is
currently activated option. For example, when “Auto” is underlined, the sweep time will be
automatically adaptable to other relevant parameter settings.
d) Activate the marker
By pressing 【Marker】, common marker will be activated and displayed in the center of the
horizontal coordinates (the frequency and amplitude will be read by the marker and shown in the
active function area). The marker reads the frequency as 1GHz and amplitude as -20dBm, as
shown in Fig. 3.3.
If the marker is not at the peak, you can press 【Peak】key to enable the marker to automatically
jump to the peak of the signal or use the knob on the front panel to manually position the marker
on the maximum value of the signal.