Challenger Spirit User manual

CHALLENGER SECURITY PRODUCTS
UNIT 2 /4 ARKWRIGHT COURT
FYLDE IND ESTATE BLACKPOOL
LANCASHIRE FY4 5DR TEL [phone] TECHNICAL
The Challenger "Spirit" is a high quality external combined sounder and
strobe unit. Features include a digital timed SAB with dual fail safe action, a
high efficiency Piezo sounder and an integral high intensity double lens
strobe.
Technical Description of the SPIRIT
+ This requires a constant 12V and 0V from the control panel
HOLD OFF This "HOLDS OFF" the piezo siren in normal operation .
- It also allows the battery to be trickle charged
STB - Provides an output from the control panel to flash the strobe and is
independent of the sounder inputs.
TRG - In normal operation this activates the sounder only when a Negative
Trigger is applied by the control panel.
PIEZO Provides the siren output to drive the piezo sounder
RTN - In normal operation this supplies a permanent signal to the control panel as
part of the 24 hour tamper loop
MICRO This is for N/C Tamper switches, which for m part of the 24 hour tamper
SWITCH circuit
BAT Battery Link. After completing all connections this link must be move d to
the ON position before fitting the bell box cover.
This enables charging of the battery and correct function of the SPIRIT.
SAB Self activating bell ( use for primary sounder )
SCB Self contained bell ( use for secondary sounder )
Note: Isolate strobe before removing the cover ( HIGH VOLTAGE )

INICATORS
ORANGE LED This is only lit whe n the 12V HOLD OFF is connected
correctly
RED LED This indicates when the TAMPER SWITCHES are
closed
JUMPERS
TIMER SELECT
T2 0 second approx
A 20 minutes approx
BATTERY SELECT
ON Allows SAB / SCB operation, plus trickle charge
OFF Isolates battery
MODE SELECT ( Inside case BLUE LINK)
SAB Will draw sounder current from on - board battery only if HOLD
OFF VOL TAGE is removed
SCB Sounder will always draw its current from the on - board battery .
Not from the control panel.
.
FACTORY PRESETS
MODE SAB action
LED Alternating LED's
Timer 20 Minute Bell Cut - Off Timer
BAT OFF
SPECIFICATION
HOLD OFF SUPPLY VOLTAGE 11 - 15V, 12V Nominal
CUT OFF TIMER Digital
MAXIMUM SOUNDER CURRENT 150mA MAX
HOLD OFF CURRENT @ 12V 65mA
BATTERY CHARGE CURRENT @ 12V 12mA
FULL CHARGE TIME @ 12V 24 Hours
FLASH RATE 60 - 120 per minut e
FLASH INTENSITY 1 Watt / second
STROBE CURRENT @ 12V 100mA
DUE TO CONTINUAL DEVELOPMENT, WE RESERVE THE RIGHT TO MODIFY ALL
PRODUCTS WITHOUT PRIOR NOTICE
INSTALLATION GUIDE
STEP OPERATION
1 Decide and select which SPIRIT feat ures are required
i.e. LED and Mode operation
2 Drill all holes required for mounting the SPIRIT. Use suitable screws
and rawl plugs to provide a strong and secure installation . Make sure
the bottom right hand screw is in a place which allows the back tamper
to operate. If the SPIRIT is removed from the wall, the bottom right
screw will break out therefore set off the back tamper.
3 Screw in the right hand tamper screw until the switch clicks.
Now wire to the control panel.
4 Depending on y our selection, the red and orange LED's will now be
either flashing side to side or c onstantly illuminated. The orange LED
displaying that HOLD OFF VOLTAGE is present and the red LED
displays that the TAMPER SWITCH is closed.
5 Fit Battery l ink to ON and remove right hand tamper screw .
6 The siren will now be sounding. Quickly fit the bell box cover and
fasten the two side screws which will silence the siren.
7 Both LED's will now once again be operating .
COMMISSIONING & TESTING
ST EP OPERATION
1 It is now possible to provide a negative trigger from the Control Panel
which will set off the sounder.
2 Open the Tamper Switch, the sounder will start and the red LED will
go out.
3 If the Timer requires testing, simply move the Timer LINK to T, press
and release the Tamper Switch. The siren will now sound for 20
seconds. Move the link back t o A and replace the cover.
E&OE