manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Chamberlain
  6. •
  7. Control Panel
  8. •
  9. Chamberlain 935EV User manual

Chamberlain 935EV User manual

1
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
• Install door control within sight of garage door, out of reach of children at a minimum
height of 5 feet (1.5 m), and away from ALL moving parts of door.
• NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross
path of closing garage door.
PREMIUM MOTION-DETECTING CONTROL PANEL
Models 935EV, 935EVC and 41A7327-1
®
Feature Overview
TIMER-TO-CLOSE (TTC) FOR MODEL 41A7327-1 ONLY
DO NOT enable TTC if operating a one-piece door. TTC is to be used ONLY with sectional doors.
The TTC can be set to automatically close your garage door after a specified period of time (1, 5,
or 10 minute intervals). The garage door opener will beep and the lights will flash before closing
the door. TTC WILL NOT work if the garage door opener is operating by battery power or if the
safety reversing sensors are misaligned. This feature is NOT intended to be the primary method of
closing the door. A keyless entry should be installed in the event of an accidental lock out when
using this feature.
Premium Motion-Detecting
Control Panel
Safety Reversing
Sensors
Yellow
LEARN Button
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
For use with MyQ™ Garage Door Openers. The features are adjustable and may be turned off or on
as desired. Refer to the Feature Settings section.
LOCK
The LOCK feature is designed to prevent activation of the garage door opener from remote
controls while still allowing activation from the door control and keyless entry. This feature is
useful for added peace of mind when the home is empty (i.e. vacation).
MOTION SENSOR
The motion sensor will automatically turn on the garage door opener lights when motion is
detected. The lights will come on for the set period of time, then shut off. The factory setting is on
and set at 4-1/2 minutes.
LIGHT BUTTON
Press the LIGHT button to turn the garage door opener lights on or off. When the lights are turned
on they will stay on until the LIGHT button is pressed again, or until the garage door opener is
activated. Once the garage door opener is activated the lights will turn off after the specified period
of time (the factory setting is 4-1/2 minutes). The LIGHT button will not control the lights when the
door is in motion.
2
RED
WHITE
WHITE
GREY
W
WH
R
RE
Installation
Install the door control within sight of the door at a minimum height of 5 feet (1.5 m) where small
children cannot reach, and away from the moving parts of the door. For gang box installations it is
not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box.
NOTE: Pre-wiring means that your garage already has wires installed for the door control.
WIRE THE DOOR CONTROL
1
2
3
1
2
3
4
5
6
1
2
3
7/16" (11 mm)
7/16" (11 mm)
Unplug the garage door opener to
ensure the door control cannot be
activated during wiring.
Strip 7/16" (11 mm) of insulation from
one end of the wire and separate the
wires.
Connect the wire to both screws on the
back of the door control. The wires can
be connected to either screw.
PRE-WIRED INSTALLATIONS: Choose any two
wires to connect, but make note of which wires
are used.
MOUNT THE DOOR CONTROL
Mark the location of the bottom
mounting hole and drill a 5/32" (4 mm)
hole.
Install the bottom screw, allowing
1/8" (3 mm) to protrude from the wall
Position the bottom hole of the door
control over the screw and slide down
into place.
Lift the push bar up and mark the top
hole.
Remove the door control from the wall
and drill a 5/32" (4 mm) hole for the
top screw.
Position the bottom hole of the door
control over the screw and slide down
into place. Attach the top screw.
WIRE TO GARAGE DOOR OPENER
Strip 7/16" (11 mm) of insulation from
the end of the wire near the garage door
opener.
Connect the wire to the red and white
terminals on the garage door opener.
The wires can be connected to either
terminal.
Reconnect power to the garage door
opener. The command LED behind the
push bar on the door control will blink
if installed correctly. To synchronize
the garage door opener and the door
control, press the push bar up to
3 times. Press until the garage door
opener activates.
PRE-WIRED INSTALLATIONS: Connect the same
wires to the garage door opener that were
previously connected to the door control.
To insert or release
wire, push in tab with
screwdriver tip.
GANG BOXDRYWALL
6ABx1-1/4" Drywall Anchors 6-32x1"
HARDWARE
1
2
3
4
5
6
- Wall -
3
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
Program
Operation
PUSH BAR
Press the push bar to open/close the door.
GARAGE DOOR OPENER LIGHTS
Press the LIGHT button to turn the garage door
opener lights on or off. When the lights are
turned on they will stay on until the LIGHT
button is pressed again, or until the garage
door opener is activated. Once the garage door
opener is activated the lights will turn off after
the specified period of time (the factory setting
is 4-1/2 minutes). The LIGHT button will not
control the lights when the door is in motion.
Press the LEARN button on the door
control to enter Programming Mode.
Press the LEARN button again, the
LED will flash once.
Press the button on the remote
control that you wish to operate
your garage door.
Enter a 4-digit personal
identification number (PIN) of your
choice on the keyless entry keypad.
Then press the ENTER button.
The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.
Repeat the steps above for programming additional remote controls or keyless entry devices.
The command LED will flash once. The command LED will flash once again.
PIN
?? ??
12
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
QZ
*
#
ENTER
0 QZ
*#
ENTER
LIGHT Button
OR
HOLD OPEN Button for the
Timer-To-Close (TTC)
Motion Sensor
1 2 3a 3b
Push Bar
1 Minute
TTC LED
5 Minute
TTC LED
10 Minute
TTC LED
TIMER-TO-CLOSE (TTC) FOR MODEL
41A7327-1 ONLY
DO NOT enable TTC if operating a one-piece
door. TTC is to be used ONLY with sectional
doors.
The TTC can be turned on or off and the time
interval can be adjusted to 1, 5, and 10 minute
intervals. Once the TTC has been set and the
door is open, the selected close interval will
blink and begin to count down to close the
door. The garage door opener will beep and the
lights will flash before closing the door.
To temporarily suspend the TTC feature press
and release the HOLD OPEN button (the HOLD
OPEN button will light solid). Press the HOLD
OPEN button again to resume normal TTC
operation.
The TTC feature will deactivate if the garage
door encounters two sequential obstructions;
or the safety reversing sensors are incorrectly
installed. The garage door will reverse open and
WILL NOT close until the obstructions are
removed or the safety reversing sensors are
correctly installed. When the obstruction has
been cleared or the safety reversing sensors
have been aligned, the door will close when the
garage door opener is activated.
MOTION SENSOR
This feature will automatically turn on the
garage door opener lights when motion is
sensed. The lights will come on for the set
period of time, then shut off.
LIGHT FEATURE
The lights will turn on when someone enters
through the open garage door and the safety
reversing sensor infrared beam is broken.
If using the garage door opener light as a work
light, turn the light on using the light button on
the wall control or the light will turn off if you
are beyond the range of the sensor.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain.com
http://help.chamberlain.com
Feature Settings
Warranty
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer purchaser of this product that it is
free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.
NOTE: If you have a Smart Control Panel®installed and
the TTC is set to a custom time, the 3 LED's on the
41A7327-1 will blink. If the 3 LED's are blinking and you
have an 41A7327-1 ONLY, press the ON button to set
the time properly.
LOCK
Activate:
Press and hold the LOCK button for
2 seconds. The command LED will flash as
long as the lock feature is activated and your
handheld remote control will not operate
your door at this time.
Deactivate:
Press and hold the LOCK button again for
2 seconds. The command LED will stop
flashing and normal operation will resume.
LOCK Button
Command LED
TIMER-TO-CLOSE (TTC) FOR MODEL
41A7327-1 ONLY
Activate:
Press and hold the ON button until one of
the TTC LEDs light up.
Then press the ON button again to cycle
through the time interval options (the
corresponding TTC LED will light for each
time interval). The garage door opener light
bulbs will blink as confirmation.
Deactivate:
Press and hold the OFF button until all TTC
LEDs turn off and a beep is heard from the
motor unit.
Temporarily hold door open
(suspend TTC):
Press and release the HOLD OPEN button.
Press the HOLD OPEN button again to
resume normal TTC operation.
ON Button
OFF Button
HOLD OPEN
Button
1 Minute
TTC LED
5 Minute
TTC LED
10 Minute
TTC LED
NOTE: DO NOT enable TTC if operating a one-piece door.
TTC is to be used ONLY with sectional doors.
LIGHT
To change the amount of time the
garage door opener lights will stay on:
Press and hold the LOCK button until the
garage door opener lights flash.* The time
interval is indicated by the number of
flashes.
To cycle through the time intervals repeat
the step above.
NUMBER OF TIMES
GARAGE DOOR OPENER
LIGHTS FLASH
TIME THE GARAGE
DOOR OPENER LIGHT
STAYS ON
1 1 ½ Minutes
2 2 ½ Minutes
3 3 ½ Minutes
4 4 ½ Minutes
LOCK Button
LIGHT Button
Command LED
NOTE: If the
command LED
is continuously
blinking, the
Lock feature
needs to be
deactivated.
Deactivate:
Press and hold the LIGHT button until the
garage door opener lights turn on, then off
again.*
Activate:
Start with the garage door opener lights
on. Press and hold the LIGHT button until
the garage door opener lights turn off,
then on again.*
LIGHT FEATURE
* Approximately 10 seconds
MOTION SENSOR
Activate/Deactivate:
Slide the motion sensor switch ON or OFF.
Motion Sensor
Switch
Motion Sensor
© 2011, The Chamberlain Group, Inc.
114A4018 All Rights Reserved

This manual suits for next models

2

Other Chamberlain Control Panel manuals

Chamberlain MyQ User manual

Chamberlain

Chamberlain MyQ User manual

Chamberlain CB10 User manual

Chamberlain

Chamberlain CB10 User manual

Chamberlain LIF-880LMW User manual

Chamberlain

Chamberlain LIF-880LMW User manual

Chamberlain LiftMaster 398LM User manual

Chamberlain

Chamberlain LiftMaster 398LM User manual

Chamberlain LiftMaster CB11 User manual

Chamberlain

Chamberlain LiftMaster CB11 User manual

Chamberlain LiftMaster Professional 98LM User manual

Chamberlain

Chamberlain LiftMaster Professional 98LM User manual

Chamberlain CIGCWC User manual

Chamberlain

Chamberlain CIGCWC User manual

Chamberlain 41A7305-1 User manual

Chamberlain

Chamberlain 41A7305-1 User manual

Chamberlain Elite K1D6761-1CC User manual

Chamberlain

Chamberlain Elite K1D6761-1CC User manual

Chamberlain 41A6345-1 User manual

Chamberlain

Chamberlain 41A6345-1 User manual

Chamberlain LiftMaster CB1 User manual

Chamberlain

Chamberlain LiftMaster CB1 User manual

Chamberlain 882LMW User manual

Chamberlain

Chamberlain 882LMW User manual

Chamberlain Security+ 2.0 41A7773-1 User manual

Chamberlain

Chamberlain Security+ 2.0 41A7773-1 User manual

Chamberlain CB202 User manual

Chamberlain

Chamberlain CB202 User manual

Chamberlain 945CB User manual

Chamberlain

Chamberlain 945CB User manual

Chamberlain 935CB User manual

Chamberlain

Chamberlain 935CB User manual

Chamberlain 880LMW User manual

Chamberlain

Chamberlain 880LMW User manual

Chamberlain 881LM User manual

Chamberlain

Chamberlain 881LM User manual

Chamberlain LiftMaster Professional CB22 User manual

Chamberlain

Chamberlain LiftMaster Professional CB22 User manual

Chamberlain C198 User manual

Chamberlain

Chamberlain C198 User manual

Chamberlain 882LM User manual

Chamberlain

Chamberlain 882LM User manual

Chamberlain 378LM User manual

Chamberlain

Chamberlain 378LM User manual

Chamberlain 935C User manual

Chamberlain

Chamberlain 935C User manual

Chamberlain Liftmaster 880LM User manual

Chamberlain

Chamberlain Liftmaster 880LM User manual

Popular Control Panel manuals by other brands

Axon Cerebrum CCP-4200B Operation manual

Axon

Axon Cerebrum CCP-4200B Operation manual

motortronics VMX2 SERIES Installation and startup guide

motortronics

motortronics VMX2 SERIES Installation and startup guide

Honeywell SMX-AUS user guide

Honeywell

Honeywell SMX-AUS user guide

Nordelettronica KIT-NE185-12S instruction manual

Nordelettronica

Nordelettronica KIT-NE185-12S instruction manual

Unitronics Vision V130-J-T2 installation guide

Unitronics

Unitronics Vision V130-J-T2 installation guide

Trane TCONT402AN32DA owner's manual

Trane

Trane TCONT402AN32DA owner's manual

Tylo CC 10 user manual

Tylo

Tylo CC 10 user manual

Fagor 8025 T CNC operating manual

Fagor

Fagor 8025 T CNC operating manual

DITEC EL12E installation manual

DITEC

DITEC EL12E installation manual

Notifier NFS2-640/E Operation manual

Notifier

Notifier NFS2-640/E Operation manual

Honeywell Galaxy 3-48C installation manual

Honeywell

Honeywell Galaxy 3-48C installation manual

Biamp TEC-X 2000 Installation & operation guide

Biamp

Biamp TEC-X 2000 Installation & operation guide

Core TOUCH S 10” quick start guide

Core

Core TOUCH S 10” quick start guide

ROHS SM812CH-MV3(T) Installation and operation guide

ROHS

ROHS SM812CH-MV3(T) Installation and operation guide

Honeywell IQ8Control C Installation instruction

Honeywell

Honeywell IQ8Control C Installation instruction

Hunt HKB-200 user guide

Hunt

Hunt HKB-200 user guide

CAME BPT TH/PLUS Installation and commissioning manual

CAME BPT

CAME BPT TH/PLUS Installation and commissioning manual

Zooper OPT1/4 User manual, maintenance guide & log book

Zooper

Zooper OPT1/4 User manual, maintenance guide & log book

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.