Chamberlain 953EV User manual

3-BUTTON REMOTE CONTROLS
MODELS 953EV, 953EVC, 956EV AND 956EVC
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate or play with remote controls.
• Activate gate or door ONLY when it can be
seen clearly, is properly adjusted and there
are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after
January 1, 1993. The garage door opener activates when the programmed button on the
remote control is pressed. The remote control can activate up to three garage door openers.
Make sure the garage door opener has a working light bulb because it is a programming
indicator.
LED LED
Locate the Program button on the
remote control.
Locate the Learn
button on the garage
door opener.
NOTE: Your garage door
opener may look different.
OR OR
Learn
LED
Learn
LED
Learn
LED
Green
or
Red/Orange
Purple Yellow Program Button
Program Button
4
Press and release the Learn
button on the garage door
opener.
3To exit programming mode,
press any remote control
button except the button
that was just programmed.
Install the visor clip.
7
Press the remote control button
programmed in step 2 until the
garage door opener lights flash
or two clicks are heard.
To test, press the programmed
button on the remote control...
1
Within 30 seconds...
The Learn LED will light.
56
Press and hold the program button
the remote control until the LED on
the front of the remote control
turns on.
Learn
Button
Click
Click
The garage door
opener will activate.
2Press and release the remote control button you wish to use the
number of times that corresponds with the garage door opener type:
# of Presses Garage Door Opener Type
1
2
3
4
Security+ 2.0TM (Yellow Learn Button)
315 MHz Security+®(Purple Learn Button)
390 MHz Security+®(Red/Orange Learn Button)
390 MHz Billion Code (Green Learn Button)
MODELS 953EV AND 953EVC MODELS 956EV AND 956EVC
GARAGE ACCESS SYSTEM
REMOTE
GARAGE ACCESS SYSTEM
KEYCHAIN REMOTE
PREPARE
PROGRAM THE REMOTE CONTROL (953EV & 953EVC)
953EV &
953EVC
956EV &
956EVC

4
Press and release the Learn
button on the garage door
opener.
3To exit programming mode,
press any remote control
button except the button
that was just programmed.
Press the remote control button
programmed in step 2 until the
garage door opener lights flash
or two clicks are heard.
1
Within 30 seconds...
The Learn LED will light.
5
Press and hold the program button
the remote control until the LED on
the front of the remote control
turns on.
Safety pin or
paper clip
Learn
Button
Click
Click
2Press and release the remote control button you wish to use the
number of times that corresponds with the garage door opener type:
# of Presses Garage Door Opener Type
1
2
3
4
Security+ 2.0TM (Yellow Learn Button)
315 MHz Security+®(Purple Learn Button)
390 MHz Security+®(Red/Orange Learn Button)
390 MHz Billion Code (Green Learn Button)
To test, press the programmed button on the remote control...
6
The garage door opener
will activate.
NOTICE: To comply with FCC and or Industry Canada rules (IC),
adjustment or modifications of this receiver and/or transmitter
are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-
210. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
BATTERY
The LED on your remote will stop flashing when the battery is low and needs to be replaced.
To replace battery, open the case as shown. Insert battery positive side up (+). Replace the battery
with only 3V CR2032 coin cell batteries. Dispose of old battery properly. To prevent possible SERIOUS INJURY or
DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
To reduce risk of fire, explosion or chemical
burn:
• Replace ONLY with 3V CR2032 coin
batteries.
• DO NOT recharge, disassemble, heat
above 212° F (100° C) or incinerate.
1-800-528-9131
114A3924D © 2013, The Chamberlain Group, Inc.
All Rights Reserved
REPLACEMENT PARTS
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
Visor Clip
(Models 953EV & 953EVC ONLY) . . . . 29B137
1
2
3
WARRANTY
www.chamberlain-diy.com
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from
defect in materials and/or workmanship for a period of 1 year from the date of purchase.
Pry open the case with a screwdriver blade.
956EV & 956EVC
Pry open the case first in the middle (1), then
at each side (2 and 3) with the visor clip.
953EV & 953EVC
PROGRAM THE REMOTE CONTROL (956EV & 956EVC)