Channel Vision IR Reciever IR-4101 User manual

Be sure the emitter is attached directly over the component’s IR receiver.
To locate the IR receiver, shine a flashlight into the unit and look for the
sensor.
The IR-4101 is an IR coax adaptor that works with
Channel Vision’s IR coax engine to enable the
transmission of Infrared remote control signals onto
the same coax cable that delivers your cable TV.
Channel Vision’s IR coax engine can be found in the
following products: IR-4000, E2200IR, E3200IR,
E4200IR, and P-0321.
How IR repeating works
Specifications: (typical)
Voltage Requirements:
IR Freq. range supported:
IR pickup range:
IR receiver head dimensions:
Color:
8-12VDC
30 kHz - 60 kHz
40 ft. @ 38kHz, 25 ft. @ 56kHz
0.65” x 0.35” x 0.25”
Black
Specifications subject to change without notice.
CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or rebuilt
parts, free of charge in the USA, for two years from the date of original purchase.
This is a no hassle warranty with no mail in warranty card needed. This warranty
does not cover damages in shipment, failures caused by other products not
supplied by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only to the
original purchaser, and a purchase receipt, invoice, or other proof of original
purchase date will be required before warranty repairs are provided.
Mail in service can be obtained during the warranty period by calling (800) 840-
0288 toll free. AReturn Authorization number must be obtained in advance and
can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops during or
after the warranty period, please contact Channel Vision Technology, your dealer
or any factory-authorized service center.
The IR-4101 includes these items:
500-167 rev A1
1 - IR receiver holster
Accessories
1 - IR coax adaptor with IR receiver
1 - hole mount
1 - tabletop mount
IR receiver head
Features:
!
!
!
Plasma Proof IR receiver
Compatible with: IR-4000, E2200IR, E3200IR, E4200IR,& P-0321
Versatile mounting accessaries: Install as
Very small receiver
In-cabinet tube type receiver
Unobtrusive desktop type receiver
Using the IR-4101 & P-0321
AB-500
TxBatt
Rew<<P
lay>FF>>
LearnStopPause
123
456
789
0
Power-/--
ChVol
LearnError
AllOff
Off
Select
TunerCDSat
VCRDVDTV
ChannelVisionTM
Point an
IR remote control
at the IR receiver
The IR receiver is wired to
the IR hub which routes the
signal to IR emitters
CD player
And the emitter
repeats the IR signal
in the other room.
IRReceiver
Model
P-1205
Pwr
Expansion
GlobalZone
Zone
Global
Emitters
+12DC
250mA
IR
Receiver
C
V
HANNEL
ISION
TM
36”
0.65”
0.35”
C
V
HANNEL
ISIONTM
C
V
HANNEL
ISIONTM
Model
P-0321
CATV Input MOD Input
Output
Power
IR Out
Pat. Pending
Input from
CATV Input from
Modulator
PartNo.HS-2
-WAYSPLITTER/COMBINER2
5MHz-1GHzAllPort DC passing
CV
HANNEL ISION
TM
IN/out
OUT/in OUT/in
Digital CATV Box
IR-4101
A0502
P-0321
TV set
CV
HANNEL ISION
S
O
U
R
C
E
ZONE
POWER
MUTE
CATV
MOD
VOL
1
2
3
4
MODEL
A0502
POWER
MOD - Selects the modulator input on the P-0321
CATV - Selects the CATV input on the P-0321

Drill a 3/4” .hole
Push the IR receiver head
through the hole.
Push the IR receiver head
through the hole in the
tabletop mount.
Mount the IR receiver to the TV or on a surface within line of sight
of your remote control.
Remove the backing from the tape and attach the
IR receiver holster in the desired location.
Snap IR receiver head into the holster
as shown.
Push the IR receiver hole
mount and IR receiver head
back into the hole.
Push the IR receiver hole
mount and IR receiver head
back into the hole in the tabletop
mount.
To secure the mount, remove
the backing from the foam tape
on the bottom of the unit and
attach the mount to any flat surface.
Insert the IR receiver head
into the IR receiver hole mount. Insert the IR receiver head
into the IR receiver hole mount.
Mounting the IR receiver: Option 1 - Using the holster
Mounting the IR receiver: Option 3 - Using the tabletop mountMounting the IR receiver: Option 2 - Using the hole mount
AB-500
TxBatt
Rew<<Play>FF>>
Learn StopPause
123
456
789
0
Power-/--
ChVol
LearnError
AllOff
Off
Select
Tuner CDSat
VCRDVDTV
ChannelVision
TM
CVHANNEL ISIONTM
Input
IR-4000
IR coax engine
ToIR coax
adaptor
IR emitter Pwr
VCR
IR-4101
IR-4000
Ch. 3 output
IR Emitter
IR Emitter
TV set
DVD player CHANNELVISION
TM
E 200IR2AB
ESeries
Part No. HS-4
-WAYSPLITTER/COMBINER4
5MHz-1GHzAll Port DC passing
CVHANNEL ISIONTM
IN/outOUT/in OUT/in
OUT/inOUT/in
DC Block
DC Block and
75 ohm terminator
HS-4
DC Passing
splitter
AB-500
TxBatt
Rew<<Play>FF>>
LearnStopPause
123
456
789
0
Power-/--
ChVol
LearnError
AllOff
Off
Select
TunerCDSat
VCRDVDTV
ChannelVisionTM
AB-500
TxBatt
Rew<<P
lay>FF>>
LearnStopPause
123
456
789
0
Power-/--
Ch Vol
LearnError
AllOff
Off
Select
TunerCDSat
VCRDVDTV
ChannelVisionTM
IR-4101
IR-4101
A basic IR system, like the one shown below, is often used when an
audio/video signal is distributed to a remote TV location using the RF
output of the device. The IR-4101 is located near the TV, allowing IR
signals to be detected, and the IR-4000 is located near the audio/video
source, providing an IR emitter output.
Basic IR-on-coax Setup Using the IR-4101 with an E-series IR modulator