Charder MS4910 User manual

1
USER MANUAL
MS4910
Stand-on Floor Scale
Please keep the instruction manual at hand all the time for future reference.

2
Explanation of Graphic Symbols on Label/Packaging
Caution, consult
accompanying documents
before use
Separate collection for
waste of electrical and
electronic equipment,
in accordance with
Directive 2002/96/EC
Manufacturer of medical
device
Manufacturing year of
medical device
Carefully read user manual
before installation and
usage, and follow
instructions for use.
Medical electrical
equipment with Type B
applied part
Device catalogue number
Authorized
representative in the
European Community
Manufacturer's batch or lot
number
Device is a medical
device
Serial number
Unique Device Identifier
Device conforms to 93/42/EEC as amended
by 2007/47/EC Medical Device Directive. Four
digit number refers to Notified Body.
Device complies with International
Organization of Legal Metrology (Class III)
requirements (verified models only)
Device complies with EC directives (verified
models only)
M: Conformity label in compliance with
Directive 2014/31/EU for non-automatic
weighing instruments
18: Year in which conformity verification was
performed and the CE label was applied. (ex:
18=2018)
0122: Refers to Notified Body for metrology

3
Copyright Notice
Charder Electronic Co., Ltd.
No.103, Guozhong Rd., Dali Dist., Taichung City 41262 Taiwan
Tel: [phone]
Fax: [phone]
Website: www.chardermedical.com E-mail: [e-mail]
Copyright© Charder Electronic Co., Ltd. All rights reserved.
This user manual is protected by international copyright law. All content
is licensed, and usage is subject to written authorization from Charder
Electronic Co., Ltd. (hereinafter Charder) Charder is not liable for any
damage caused by a failure to adhere to requirements stated in this
manual. Charder reserves the right to correct misprints in the manual
without prior notice, and modify the exterior of the device for quality
purposes without customer consent.
Charder Electronic Co., Ltd.
No. 103, Guozhong Rd., Dali Dist.,
Taichung City, 41262 Taiwan

4
CONTENTS
I. Safety Notes .......................................................................... 5
A. General Information............................................................ 5
B. EMC Guidance and Manufacturer's Declaration........................ 8
II. Installation..........................................................................12
A. Assembly..........................................................................12
B. Inserting Batteries .............................................................15
C. Using Adapter ...................................................................17
D. Attaching Height Rod to Column ..........................................18
E. Attaching Thermal Printer ...................................................21
III. Indicator............................................................................24
A. Indicator and Key Functions ................................................24
B. Display layout....................................................................25
IV. Using Device .......................................................................26
A. Basic Operation .................................................................26
B. Hold.................................................................................26
C. BMI..................................................................................26
D. Tare .................................................................................27
E. Pre-Tare............................................................................28
F. Print .................................................................................31
V. Device Setup ........................................................................32
A. Setting Time & Date...........................................................32
B. Device Setup.....................................................................33
VI. Setup USB Connection to PC ...............................................35
VII. Wireless Connection..........................................................38
VIII. Troubleshooting...............................................................39
IX. Product Specifications ........................................................41
X. Declaration of Conformity ....................................................44

5
I. Safety Notes
A. General Information
Thank you for choosing this Charder Medical device. It is designed to be
easy and straightforward to operate, but if you encounter any problems
not addressed in this manual, please contact your local Charder service
partner.
Before beginning operation of the device, please read this user manual
carefully, and keep it in a safe place for reference. It contains important
instructions regarding installation, proper usage, and maintenance.
Intended Use
This device is intended to measure the weight of subjects who can stand
unassisted, for diagnosis of weight-related issues by professionals.
General Handling
Device should be placed on stable, flat, solid, non-slippery surface.
Usage on soft surfaces (ex: carpet) may result in inaccurate results.
Ensure all parts are properly locked and tightened before operating
the device.
Device is intended to measure one subject at a time.
Safety Instructions
Batteries should be kept away from children. If swallowed, promptly
seek medical assistance.
Expected service life: 5 years.
Always comply with appropriate regulations when using electrical
components under increased safety requirements.
Ensure voltage marked on power supply matches mains power
supply.
The device is intended for indoor use only.
Observe permissible ambient temperatures for use
Environmental
All batteries contain toxic compounds; batteries should be disposed
of via designated competent organizations. Batteries should not be
incinerated.
Cleaning
Device surface should be cleaned using alcohol-based wipes.
Corrosive cleansing liquids should not be used. Pressure-washers
should not be used.

6
Do not use large amounts of water when cleaning the device, as it
may cause damage to the internal electronics.
Always disconnect device from mains power before cleaning.
Maintenance
Device does not require routine maintenance. However, regular
checking of accuracy is recommended; frequency to be determined
by level of use and state of device. If results are inaccurate, please
contact local distributor.
Warranty/Liability
The period of warranty shall be eighteen (18) months, beginning on
the date of purchase. Please retain your receipt as proof of purchase.
No responsibility shall be accepted for damage caused through any
of the following reasons: unsuitable or improper storage or use,
incorrect installation or commissioning by the owner or third parties,
natural wear and tear, changes or modifications, incorrect or
negligent handling, chemical, electrochemical, or electrical
interference.
All maintenance, technical inspections, and repairs should be
conducted by an authorized Charder service partner, using original
Charder accessories and spare parts. Charder is not liable for any
damages arising from improper maintenance or usage.
Disposal
This product is not to be treated as regular household waste, but
should be taken to a designated collection points for electronics.
Further information should be provided by local waste disposal
authorities.
Warning
Only the original adapter should be used with the device. Using an
adapter other than the one provided by Charder may cause
malfunction.
Do not touch the power supply with wet hands.
Do not crimp the power cable, and avoid sharp edges.
Do not overload extension cables connected to the device.
Route cables carefully, to avoid tripping.
Keep device away from liquids.
Do not remove the plug by yanking on the cable.
Use only a correctly wired (100-240VAC) outlet, and do not use a
multiple outlet extension cable.

7
Do not under any circumstances dismantle or alter the device, as this
could result in electric shock or injury as well as adversely affect the
precision of measurements.
Do not place the device in direct sunlight, or in close proximity to an
intense heat source. Excessively high temperatures may damage the
internal electronics.
Incident Reporting
Any serious incident that has occurred in relation to the device
should be reported to the manufacturer, EU representative (if device
is used in EU member state), and competent authority of
user/subject's member state.

8
B. EMC Guidance and Manufacturer's Declaration
Guidance and manufacturer’s declaration-electromagnetic emissions
The MS4910 Stand-on Floor Scale is intended for use in the electromagnetic environment
specified below. The customer or the user of the device should assure that it is used in such
an environment.
Emission test
Compliance
Electromagnetic
environment-guidance
RF emissions CISPR 11
Group 1
The device uses RF energy only for
its internal function. Therefore, its
RF emissions are very low and are
not likely to cause any interference
in nearby electronic equipment.
RF emissions CISPR 11
Class B
The device is suitable for use in all
establishments, including domestic
establishments and those directly
connected to the public low-voltage
power supply network that supplies
buildings used for domestic
purposes.
Harmonic emissions IEC
61000-3-2
Class A
Voltage fluctuations /flicker
emissions IEC 61000-3-3
Compliance
Guidance and manufacturer’s declaration-electromagnetic immunity
The MS4910 Stand-on Floor Scale is intended for use in the electromagnetic environment
specified below. The customer or the user of the device should assure that it is used in such
an environment.
Immunity test
IEC 60601
test level
Compliance
level
Electromagnetic
environment-guidance
Electrostatic
discharge(ESD)
IEC 61000-4-2
±8 kV contact
±2 kV, ± 4 kV,
± 8 kV, ± 15 kV
air
±8 kV contact
±2 kV, ± 4 kV,
± 8 kV, ± 15 kV
air
Floors should be wood, concrete
or ceramic tile. If floors are
covered with synthetic material,
the relative humidity should be
at least 30%

9
Electrical fast
transient/burst
IEC 61000-4-4
± 2kV for
power supply
lines
+ 1kV for
input/output
lines
+ 2kV for power
supply lines
+ 1kV for
input/output
lines
Mains power quality should be
that of a typical commercial or
hospital environment.
Surge IEC
61000-4-5
± 1kV line(s) to
line(s)
± 2kV line(s) to
earth
+ 1kV line(s) to
line(s)
+ 2kV line(s) to
earth
Mains power quality should be
that of a typical commercial or
hospital environment.
Voltage Dips,
short interruptions
and voltage
variations on
power supply
input lines IEC
61000-4-11
0% UT for 0,5
cycle
0% UT for 1
cycle
70% UT(30%
dip in UT) for
25 cycles
0% UT for 5 s
0% UT for 0,5
cycle
0% UT for 1
cycle
70% UT(30%
dip in UT) for 25
cycles
0% UT for 5 s
Mains power quality should be
that of a typical commercial or
hospital environment. If the
user of the device requires
continued operation during
power mains interruptions, it is
recommended that the device
be powered from an
uninterruptible power supply or
a battery.
Power
frequency(50/60
Hz) magnetic field
IEC 61000-4-8
30 A/m
30 A/m
The device power frequency
magnetic fields should be at
levels characteristic of a typical
location in a typical commercial
or hospital environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
Guidance and manufacturer’s declaration-electromagnetic immunity
The MS4910 Stand-on Floor Scale is intended for use in the electromagnetic environment
specified below. The customer or the user of the device should assure that is used in such an
environment.
Immunity test
IEC 60601 test
level
Compliance
level
Electromagnetic
environment-guidance
Conducted RF
IEC 61000-4-6
Radiated RF IEC
61000-4-3
3 Vrms
150 KHz to 80 MHz
6 V in ISM bands
between 0,15 MHz
and 80 MHz
80 % AM at 1 kHz
3 V/m
3 Vrms
150 KHz to 80
MHz
6 V in ISM
bands between
0,15 MHz and
80 MHz
80 % AM at 1
Portable and mobile RF
communications equipment
should be used no closer to any
part of the device including
cables, than the recommended
separation distance calculated
from the equation applicable to

10
80MHz to 2,7 GHz
kHz
3 V/m
80MHz to 2,7
GHz
the frequency of the
transmitter.
Recommended separation
distance:
d = 1,2 √P
d = 1,2 √P 80MHz to 800 MHz
d = 2,3 √P 800MHz to 2,5 GHz
Where P is the maximum output
power rating of the transmitter
in watts (W) according to the
transmitter manufacturer and d
is the recommended separation
distance in metres (m).
Field strengths from fixed RF
transmitters, as determined by
an electromagnetic site surveya,
should be less than the
compliance level in each
frequency rangeb.
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the device is used
exceeds the applicable RF compliance level above, the device should be observed to
verify normal operation. If abnormal performance is observed, additional measures may
be necessary, such as re-orienting or relocating the device.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

11
Recommended separation distance between portable and mobile RF
communications equipment and the MS4910 Stand-on Floor Scale
The device is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the device can help prevent
electromagnetic interference by maintaining a minimum distance between portable and
mobile RF communications equipment (transmitters) and the device as recommended
below, according to the maximum output power of the communications equipment.
Rated maximum
output power of
transmitter
W
Separation distance according to frequency of
transmitter m
150 kHz to 80
MHz
d =1,2√P
80 MHz to 800
MHz
d =1,2√P
800 MHz to 2,5
GHz
d =2,3√P
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended
separation distance d in metres (m) can be estimated using the equation applicable to the
frequency of the transmitter, where p is the maximum output power rating of the
transmitter in watts (W) according to the transmitter manufacturer.
NOTE1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range
applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.

12
II. Installation
A. Assembly
Standard Column
1. Fasten and tighten four screws at the bottom of the base. Ensure four
adjustable feet and stability foot are at same level before using device.
Castor wheel column
1. Fasten and tighten four screws at the bottom of the base
Four screws

13
2. Ensure four adjustable feet and stability foot are at the same level
before using the device. Rotate counter-clockwise to extend, clockwise to
retract
Stability foot
Adjustable feet

14
3. Retract stability foot before moving device using castor wheels
Note: rotate counter-clockwise to extend, clockwise to retract
Ensure stability foot is retracted before using castor wheels

15
B. Inserting Batteries
1. Open battery housing cover
2. Accessing batteries
3. Use either rechargeable battery pack, or AA batteries
4. Ensure batteries are installed into the housing correctly
Take out the battery
housing

16
5. Install the battery housing into the compartment, and make sure the
right side of housing pin is facing towards inside of the connecting
position
Rechargeable
Battery Housing
AA-size Battery Housing

17
6. Slide back the cover to close the battery housing compartment. Turn
on power to confirm that battery is correctly installed.
Using Rechargeable Battery (optional)
The rechargeable battery should be recharged at least once every 3
months, regardless of if the device has been used. Battery can be
charged by plugging device's exclusive adapter into AC Connector Port.
After a long period in storage (e.g. >3 months), the battery should run a
full cycle (charge/discharge) to allow it to restore full capacity.
Ensure rechargeable battery housing is installed and inserted properly
into the compartment.
If prompt displays on the LCD, please charge battery
promptly to avoid battery damage.
C. Using Adapter
1. Connect adapter to indicator before connecting to mains power supply
2. Disconnect adapter from mains power supply before unplugging
adapter pin from indicator.
AC Connector Port

18
D. Attaching Height Rod to Column
Standard (Narrow) Column
Step 1. Attach two fixing blocks to
column using four flat-head
screws
Step 2. Attach height rod to blocks
using two flat-head screws
Item
Name
Quantity
1
Fixing block screws
4
2
Fixing blocks
2
3
Height Rod to fixing block screws
2

19
Castor Wheel Column
1. Attach brackets to column with
round-head screws
2. Attach height rod to brackets
using flat-head screws
Item
Name
Quantity
1
M5x0.8x11 round head screw
4
2
Relief Bushing
2
3
Bracket for HM200D/HM201D/HM201M
2
4
Height Rod (Compatible with:
HM200D/HM201D/HM201M)
1
5
M5x10L flat head screw
2
6
Fixing block
2
7
M5x0.8x11
4
1
1
2
3
3
4
5
7
6

20
Connecting height rod to indicator (HM200D/HM201D)
Digital height rod data
transmission port on indicator
Secure excess cable
to column