Chattanooga Revolution Wireless User manual

1
Service Manual

TABLE OF CONTENTS
1
FOREWORD................................................................2
SAFETY INSTRUCTIONS ..........................................3
PRECAUTIONARY DEFINITIONS ...................................... 3
OVERVIEW ..................................................................... 9
DIAGRAM SYSTEM OVERVIEW .....................................11
WIRELESS COMMUNICATION ......................................12
GLOBAL SPECS..............................................................13
REMOTE CONTROL SPECS ............................................14
MODULE SPECS ............................................................15
DOCKING STATION SPECS ............................................ 15
COMPLETE SET 4CHANNELS PL15................................ 17
REMOTE CONTROL.......................................................19
MODULE.......................................................................20
DOCKING STATION 4CHANNELS ..................................21
EXPLODED VIEWS.........................................................22
GENERAL TROOBLESHOOTING PROCEDURE ................23
PREPARING TO TROUBLESHOOT THE DEVICE AND
ACCESSORIES ...............................................................24
HOW TO PAIR AMODULE.............................................26
CHARGING AND POWERING ON PROBLEMS ................26
ELECTROSTIMULATION ISSUES ....................................30
MECHANICAL AND CASING ISSUES...............................32
OTHERS ........................................................................33
MODULE LED INDICATION............................................ 34
DOCKING STATION LED INDICATION ............................36
FIRMWARE................................................................... 37
SERVICING THE DOCKING STATION.............................. 39
REMOTE CONTROL AND MODULE INTERACTION.........43
DOCKING STATION FUNCTIONALITIES ......................... 46
VISUAL INSPECTION .....................................................47
GENERAL USER MAINTENANCE.................................... 50
CARE............................................................................. 50
SAFETY INSPECTIONS ...................................................50
WARANTY ....................................................................51

FOREWORD
2
Read, understand and follow all safety precautions and information contained in the manual. This information is intended
to be used by technicians that have been trained and certified by DJO GLOBAL.
Specifications put forth in this manual were in effect at the time of publication. However, owing to DJO GLOBAL’s policy of
continual improvement, changes to these specifications may be made at any time without obligation on the part of DJO
GLOBAL.
DJO GLOBAL requires that all Field Technicians stay informed and trained on all changes pertaining to the Chattanooga®
Revolution Wireless.
Technicians repairing the Chattanooga® Revolution Wireless agree to assume all risk and liability associated with this
process.
The Chattanooga® Wireless Professional is to be used only under the prescription and supervision of a licensed
practitioner.
© 2016 DJO, LLC. Any use of editorial, pictorial or layout composition of this publication without express written consent from DJO
GLOBAL is strictly prohibited. This publication was written, illustrated, and prepared for distribution by DJO GLOBAL

SAFETY INSTRUCTIONS
3
PRECAUTIONARY DEFINITIONS
The precautionary instructions found in this section and
throughout this manual are indicated by specific symbols.
Understand these symbols and their definitions before
operating this equipment. The definitions of these
symbols are as follows:
CAUTION
Text with a “CAUTION” indicator will explain possible
safety infractions that could have the potential to cause
minor to moderate injury or damage to equipment.
WARNING
Text with a “WARNING” indicator will explain possible
safety infractions that will potentially cause serious injury
and equipment damage.
DANGER
Text with a “DANGER” indicator will explain possible
safety infractions that are imminently hazardous
situations that would result in death or serious injury.
Explosion Hazard
Text with an “Explosion Hazard”
indicator will explain possible safety
infractions if this equipment is used in
the presence of flammable anesthetics.
Dangerous Voltage
Text with a “Dangerous Voltage”
indicator serves to inform the user of
possible hazards resulting in the
electrical charge delivered in certain
program configurations of waveforms.
BioHazardous materials
Text with a “Biohazard” indicator
serves to inform the user of possible
hazards resulting in improper handling
of components and accessories that
have come in contact with bodily
fluids.
Non-ionizing electromagnetic
radiation
Text with a “Non-Ionizing
Electromagnetic Radiation” indicator
informs the user of possible hazards
resulting from elevated potentially
dangerous levels of non-ionizing
radiation.
NOTE: Throughout this manual, “NOTE” may be found.
These Notes are helpful information to aid in the
particular area or function being described.
DANGER
Stimulus delivered by the waveforms of this
device, in certain configurations, will deliver a
charge of 25 microcoulombs (µC) or greater per
pulse and may be sufficient to cause
electrocution. Electrical current of this
magnitude must not flow through the thorax
because it may cause a cardiac arrhythmia.
Users with an implanted neurostimulation
device must not be treated with or be in close
proximity to any shortwave diathermy,
therapeutic ultrasound diathermy, or laser
diathermy anywhere on their body. Energy from
diathermy (shortwave, microwave, ultrasound,
and laser) can be transferred through the
implanted neurostimulation system, can cause
tissue damage, or can result in severe injury or
death. Injury, damage, or death can occur during
diathermy therapy even if the implanted
neurostimulation system is turned off.
The solvents of adhesives and flammable
solutions used for cleaning and disinfecting
should be allowed to evaporate before the unit
is used.

SAFETY INSTRUCTIONS
4
DANGER
DO NOT connect the unit to an electrical
supply without first verifying that the power
supply is the correct voltage. Incorrect voltage
may cause unit damage, malfunction, electrical
shock, fire, or personal injury. Your unit was
constructed to operate only at the electrical
voltage specified on the Voltage Rating and
Serial Number plate. Contact your DJO dealer if
the unit is not properly rated.
WARNING
•U.S.A Federal Law restricts these devices to
sale by, or on the order of, a physician or
licensed practitioner. This device should be
used only under the continued supervision
of a physician or licensed practitioner.
•Be sure to read all instructions for operation
before treating a patient.
•Only authorized individuals are allowed to
operate the Revolution Wireless. Individuals
are authorized after receiving training in the
operation of the unit and reading this
operating on manual
•The long-term effects of chronic electrical
stimulation are unknown.
•TENS is not effective for pain of central
origin (including headache).
•TENS waveforms have no curative value.
•TENS is a symptomatic treatment, and as
such, suppresses the sensation of pain which
would otherwise serve as a protective
mechanism.
•Before using the therapy unit, the operator
must ascertain that it is in correct working
order and operating condition. The cables
and connectors, in particular, must be
checked for signs of damage. Damaged parts
must be replaced immediately, before use.
•Stop therapy immediately if you have doubts
about the device settings and/or the therapy
protocol.
•Patients must be fully conscious while being
instructed in the use of the therapy unit and
during therapy.
WARNING
•Do not treat through clothing.
•Stop treatment immediately if patient
experiences discomfort or pain.
•The choice of the therapy parameters to
program, of the therapy protocols and
electrode placement is restricted to the
responsible physician or therapist. It is the
physician’s or therapist’s decision whether
or not to use the unit on a specific patient.
•The patient must be familiar with the
functions of the Revolution Wireless remote
control with the modules and the remote
control must be within easy reach of the
patient, allowing them to stop therapy, if
needed. Patients unable to operate the
emergency stop function (either by stopping
on the remote control or by turning off the
modules), e.g. paralytic patients, must never
be left unattended during therapy.
•Use of accessories other than those
specified in this User Manual may increase
electrical emissions, decrease electrical
immunity or lead to unsafe conditions.
•The utmost caution is advised under the
following conditions. Depending on the
judgment of the responsible physician, the
unit may only be applied under supervision
and with the parameters defined by the
responsible physician. Otherwise the
exercise may be too strenuous for the
patients with:
1. Hypertension (> stage 2), ischemic heart
disease and cerebrovascular diseases
2. Cardiovascular diseases
3. Pregnancy. Safety of powered muscle
stimulators for use during pregnancy has not
been established.
4. Under 16 years of age
Never apply the electrodes as follows:
•Stimulation should not be applied
transcerebrally, or on the eyes.
• Stimulation should not be applied over the
anterior neck or mouth. Severe spasm of the
laryngeal and pharyngeal muscles may occur
and the contractions may be strong enough
to close the airway or cause difficulty in
breathing.

SAFETY INSTRUCTIONS
5
WARNING
•Counter-laterally, i.e. do not use two poles
connected to the same channel on opposite
sides of the body.
• Stimulation should not be applied over
swollen, infected, or inflamed areas or skin
eruptions, e.g., phlebitis, thrombophlebitis,
varicose veins, etc.
•Stimulation should not be applied
transthoracically in that the introduction of
electrical current into the heart may cause
cardiac arrhythmia.
• Stimulation should not be applied over the
carotid sinus nerve particularly in patients
with a known sensitivity to the carotid sinus
reflex.
• Stimulation should not be applied over, or in
proximity to, cancerous lesions.
• If the person is pregnant or menstruating do
not place electrodes directly on the uterus
area or connect pairs of electrodes on either
side of the abdomen to avoid any risk for the
mother and/or the baby.
• Keep electrodes separated during treatment.
Electrodes in contact with each other could
result in improper stimulation or skin burns
•Extreme caution should be taken when in
use around small children and babies!
Sufficient distance to the device and its
accessories is mandatory for their safety!
•Never leave the device unattended when it
is switched on! Switch the device off and
disconnect the electrodes from the modules!
•After use, store the device in a safe place to
avoid other people not informed to use the
device!
•This device is not a toy but a medical device
that misunderstanding use can cause
damages!
WARNING
Shock hazard — strictly observe the following
warnings. Failure to do so could endanger:
•Before use allow the Revolution Wireless to
reach room temperature. If the unit has
been transported at temperatures below 0
°C (32°F), leave it to reach at room
temperature for about 2 hours, until any
condensation has disappeared.
•Electrosurgical equipment or defibrillators.
Disconnect the electrodes from the device
before using electrosurgical equipment, or a
defibrillator, to avoid cutaneous burns from
the electrodes and destroying the device.
•Electronic surveillance equipment. Do not
apply stimulation near electronic
surveillance equipment (e.g. cardiac
monitors, ECG alarms), as there is a risk they
may not work properly whilst the electrical
stimulation device is being used.
•Electromagnetic radiation. Do not use the
stimulator in areas in which unprotected
devices are used to emit electromagnetic
radiation. Portable communications
equipment can interfere with the device.
•Cancer. Do not apply stimulation if you have
progressive cancer or near any cancerous
tumor. The increased metabolism, caused by
certain modes of stimulation, is likely to
encourage cancer cells to spread
•Muscle shortening. During the muscular
contraction phase it is recommended to hold
the extremities of the stimulated limbs to
avoid any shortening of the muscle during
contraction, which could cause cramps.
•Contralateral stimulation. Do not use two
terminals connected to the same channel on
opposite segments of the body (for example,
a positive terminal on the left arm and a
negative terminal on the right arm).
•Loss of sensation. Proceed with caution if
stimulation is applied to areas of the skin
whose level of sensation is lower than
normal. Do not apply stimulation to a person
who cannot express themselves.
•Battery leakage. If there is leak from a
component, take steps to ensure the liquid
does not come into contact with skin or
eyes. Should this occur, wash the affected
area with water and consult a doctor.
•Strangulation. Do not wind cables around
the neck. Tangled cables can cause
strangulation.
•Post-surgery. Proceed with caution after
recent surgery.

SAFETY INSTRUCTIONS
6
•Accessibility of the power adaptor. The plug
socket must be close to the power adaptor
and be easily accessible.
•Internal bleeding. Proceed with caution if
you are prone to internal bleeding; for
example, after an injury or a fracture
WARNING
The Revolution Wireless must only be operated
in dry rooms.
•Do not use the Revolution Wireless in water
or in a humid atmosphere (sauna, Bath,
Shower etc.) that would cause electronic
failure.
•Water protection. The unit is not protected
from the ingress of water
•When connecting the unit to other
equipment or when creating a medical
system, check that the sum of leakage
currents will not cause any hazard. Please
contact DJO GLOBAL if you have questions
regarding this matter.
•No modification of this equipment is
allowed.
•Do not open the product and its accessories
as there is risk of electrocution
•Before cleaning and service interventions,
turn the remote control and the modules off
and disconnect the tablet from the power
line by removing the power cord from the
wall outlet.
•Liquids and foreign material (such as dust,
metal etc.) must not be allowed to enter
the remote control, the modules, the
charging tablet or the power supply. If such
material has entered into the units, it must
be immediately checked by a service
technician, before it can be reused.
•Electricity supply. Never connect the
stimulation cables to an external power
supply, as there is a risk of electrocution.
•Do not apply stimulation near the area of an
implant, such as cochlear implants,
pacemakers, skeletal anchorage or electric
implants. This could cause an electrical
shock, burns, electrical interference or
death.
•Never use the Revolution Wireless or the AC
adaptor if it is damaged or open. There is a
risk of electric shock.
•Disconnect the AC adaptor immediately if
there is abnormal heating or smell, or if
smoke comes from the AC adaptor or the
device.
•Do not place the docking station in a
confined space (carrying case, drawer etc.)
when charging the device. There is a risk of
electrocution.
WARNING
Equipment malfunction —these warnings refer
to potential equipment mailfunctions that could
result in patient hazards
•Magnetic and electrical fields are capable of
interfering with the proper performance of
the unit. For this reason make sure that all
external devices operated in the vicinity of
the unit comply with the relevant EMC
requirements. ¬ Devices that intentionally
radiate electromagnetic energy, such as X-
ray equipment, MRI devices, ¬radio systems
and cell phones are possible sources of
interference, as well as RFID equipment (e.g.
electromagnetic security systems).Keep the
unit away from such equipment and verify
its performance before use. Foradditional
information, refer to the EMC section of this
Manual.
•Do not use the Revolution Wireless within 3
feet of short wave or microwave devices as
this could alter the currents generated by
the stimulator. If you are in any doubt as to
the use of the stimulator in close proximity
to another medical device, seek advice from
the manufacturer of the latter or from your
doctor.
WARNING
•Exercise caution when using electrotherapy
while the patient is connected to monitoring
equipment with electrodes attached to the
body. Stimulation could disrupt the signals
sent to the monitoring equipment.

SAFETY INSTRUCTIONS
7
•Refer repair and maintenance to authorized
persons. Persons are authorized after
training by a specialist trained and
commissioned by the manufacturer.
•Do not disassemble or modify the Revolution
Wireless or its accessories. This may cause
damage, malfunction, electrical shock, fire,
or personal injury.
•Inspect the revolution Wireless and it’s
accessories for damage and loose
connections at least once a year. Damaged
and worn parts must be immediately replaced
with original spare parts by authorized staff.
•Do not use the device if you are connected to
a high-frequency surgical instrument as this
could cause skin irritation or burns under the
electrodes
CAUTION
•Read, understand, and practice the
precautionary and operating instructions
found in this manual. Know the limitations
and hazards associated with using electrical
stimulation. Observe any precautionary and
operational decals placed on the unit.
Patient hazard — these cautions need to be
observed to avoid the risk of electrical shock
or other negative effects to the patient.
•The device is designed to comply with
electromagnetic safety standards. This
equipment generates, uses, and can radiate
radiofrequency energy and, if not installed
and used in accordance with instructions,
may cause harmful interference to other
devices in the vicinity. However, there is no
guarantee that interference will not occur in
a particular installation. Harmful
interference to other devices can be
determined by turning this equipment on
and off. Try to correct the interference by
using one or more of the following:
-Reorient or relocate the receiving device
-Increase the separation between the
equipment (refer to the EMC section in this
manual for recommended separation
distances)
-Connect the equipment to an outlet on a
different circuit.
-Consult your DJO dealer for assistance.
-Do not apply stimulation close to metal.
Remove jewelry, piercings, belt buckles or
any other metallic product or device in the
area of stimulation.
-Be careful if the patient has sensitivity
problems or is not able to communicate that
he or she feels discomfort, however light.
-Never begin an initial stimulation session on
a person who is standing. The first five
minutes of stimulation must always be
performed on a person who is sitting or lying
down. In rare instances, people of a nervous
disposition may experience a vasovagal
reaction. This is of psychological origin and
is connected with a fear of the muscle
stimulation as well as surprise at seeing one
of their muscles contract without having
intentionally contracted it themselves. A
vasovagal reaction causes heart to slow
down and blood pressure to drop, which
produces a feeling weakness and a tendency
towards fainting. If this does occur, all that
is required is to stop the stimulation and for
the person to lie down with the legs raised
until the feeling of weakness disappears (5
to 10 minutes)
-Never allow muscular contraction during a
stimulation session to result in movement.
You should always stimulate isometrically;
this means that the extremities of the limb
in which a muscle is being stimulated must
be firmly fixed, so as to prevent any
movement that results from contraction.
-Do not disconnect any module that is
switched on during the stimulation session.
They must be switched off first.
-Do not use the stimulator while driving,
operating machinery, or during any activity
in which involuntary muscle contractions
may put the user at undue risk of injury. Do
not apply stimulation during sleep.
-Do not use the stimulator at altitudes of
over 9,800 feet.

SAFETY INSTRUCTIONS
8
CAUTION
-Always turn off the stimulator before moving
or removing any electrodes during a session,
to avoid electrical shock to the patient.
-Do not try to place electrodes on a body part
not directly visible without assistance.
-Attach the electrodes in such a way that
their entire surface is in contact with the
skin.
-For reasons of hygiene, each patient must
have their own set of electrodes. Do not use
the same electrodes on different patients.
-Contaminated electrodes or gel can lead to
infection.
-Use of electrodes with degraded hydrogel
can result in burns to the skin.
-Size of electrodes. Do not use electrodes
with an active area of less than 16 cm² due
to the risk of associated burning. Proceed
systematically with caution when the density
of the current is over 2 mA/cm².
-Do not place the electrodes in water.
-Do not apply solvents of any kind to the
electrodes.
-Skin irritation. Some patients may
experience skin irritation or hypersensitivity
due to the electrical stimulation or electrical
conductive medium. The irritation can
usually be reduced by using an alternate
conductive medium, or alternate electrode
placement. If redness of the skin is observed
under the electrode, do not start another
stimulation session on the same area if the
redness is still visible.
-Instructions for electrodes. See the usage
and storage instructions displayed on the
bag of electrodes.
CAUTION
-Equipment damage
-Do not let the modules get in contact with
massage oils or any other products of the
same type that could damage the device or
its accessories.
-Check that the voltage and frequency ratings
of your local power line are those indicated
on the type plate of the power supply.
-Do not expose the revolution Wireless to
direct sunlight, because some of the
components may reach unacceptably high
temperatures.
-The unit is not protected from the ingress of
water droplets from rain if used outside the
carrying case
-The presence of children, pets and vermin
does not normally affect the proper
functioning. However, make sure that these
sources do not contaminate the
physiotherapy unit and keep them away
from it. Also, keep the unit clean and protect
it from dust and lint. The safety rules and
regulations set forth apply in any case.
-It is recommended to use the transport bag
that comes with the unit, for transport of
the device, and to use a proper transport
box to ship it.
-Always use the AC adaptor (power supply)
provided by the manufacturer to recharge
the unit.
-Do not store the modules and remote
control for a long time with uncharged
batteries.
-Only use electrodes supplied by the
manufacturer. Other electrodes may have
electrical properties that are unsuitable for
or may damage the Revolution Wireless.

THEORY OF OPERATION
9
OVERVIEW
Wireless modules
In addition to a remote control and a docking station, the Chattanooga® Revolution Wireless device is provided with
wireless modules. A stimulation module consists of two pods, each of them will be clipped to the electrodes to make a
connection to the user’s skin. The first pod contains the following parts:
•Battery
•Charging system
The second pod contains:
•Stimulation electronic, incl. main processor.
•User interface (button & LED)
•Radio Frequency communication (RF) part
The RF part implements a proprietary communication protocol operating on the 2.4 [GHz] band. The network protocol
handles communication from and to the remote control, and support a time synchronization mechanism allowing several
stimulation modules to operate simultaneously without creating pulse overlap (patented technology).
Intended use
The Chattanooga Revolution Wireless is a clinical electrotherapy device intended for use under the supervision of a
Healthcare Professional.
Indications for Use:
As an NMES device, indications are for the following conditions:
- Retarding or preventing disuse atrophy
- Maintaining or increasing range of motion
- Re-educating muscles
- Relaxation of muscle spasms
- Increasing local blood circulation
- Prevention of venous thrombosis of the calf muscles immediately after surgery
As a TENS device, indications are for the following conditions:
- Symptomatic relief and management of chronic, intractable pain
- Post-surgical and post-trauma acute pain
As a pulsed-current device, indications are for the following conditions:
- Relaxation of muscle spasm
-Increasing local blood circulation
-Retardation or prevention of disuse atrophy
-Maintenance or increase of range of motion

THEORY OF OPERATION
10
Figure 1 : Remote control, module and docking station 4 channels

THEORY OF OPERATION
11
DIAGRAM SYSTEM OVERVIEW
The figure below shows the interaction between the systems and subsystems during an electrostimulation session. The
modules transmit the electrical signal via the electrodes placed on the skin. The electrical signal is controlled by the remote
(wireless connection).
Battery
Electrostimulation Commands
Interface Subsystem Stimulation
Pod
Battery Pod Electrode
Electrode
Human
Skin
Figure 2 : Electrostimulation session diagram

THEORY OF OPERATION
12
WIRELESS COMMUNICATION
The wireless communication between the remote control and the module is made through a radio frequency node. A RF
node is a hardware structure containing a MCU. It operates according to a defined protocol and drives the wireless
transceiver (transmitter + receiver) which allows RF-communications.
The Chattanooga® Revolution Wireless communications are made with a star network where the modules (M) are the
slaves and the remote control (RC) is the single master. Every module communicates only with the master through a RF
node, they do not communicate between each other, even in case of emergency. A network composed with one master
and one or several slaves is called a piconet (P). The diagram below shows two piconets. P1 controls 3 modules and P2 only
1 module.
For the remote, the SPI serial communication interface shall be used to connect the main processing unit that needs to send
and receive information to the RF part which will forward them to the modules.
Figure 4 : Communication protocol diagram
Figure 3 : Network communication diagram

SPECIFICATION
13
GLOBAL SPECS
Operating conditions
-Temperature: 0° C to 40° C (32 °F to 104 °F)
-Relative Humidity: 30% to 75%
-Atmospheric Pressure: 700hPa to 1060hPa
Storage and transportation conditions:
-Temperature: - 20° C to +45°C (-4 °F to 113 °F)
-Relative Humidity: max 75%
-Atmospheric Pressure: 700hPa to 1060hPa
The remote control has a LCD TFT 320X240 pixels display of 2.4’’ to 2.6’’. Elements can be displayed using any colors
comprised in a color space of 65K colors (R:5-bit, G:6-bit, B:5-bit).
Battery
Remote control battery: Lithium Polymer (LiPo) rechargeable 3.7[V] / ≥ 1500[mAh].
Module battery: Lithium Polymer (LiPo) rechargeable 3.7[V] / ≥ 450[mAh].
AC adaptor: Only AC adaptor 5[V] / 3.5[A] bearing the part number 649028 can be used to recharge the Wireless
Professional device.
The device is made to be recharged whatever is the state of the battery. There’s no need to empty the batteries (of the
remote or the modules) to charge them back.
NOTE: For the remote control and the modules battery maintenance, refer to the MAINTENANCE chapter of this document.
RF data
Frequency band of emission and reception: 2.4 [GHz] ISM (2.4-2.4835 [GHz])
Modulation type and frequency characteristics: GFSK, +/- 320 [kHz] deviation
Effective radiated power: 4.4 [dBm]
Chattanooga® Revolution Wireless may be interfered by other equipment, even if that other equipment complies with
CISPR EMISSION requirements.
Electrical characteristics
Without specific information, all electrical specifications are given for an impedance of 500-1000 [Ω] per channel.
Channels: Four independent and individually adjustable channels electrically insulated from each other.
For the Chattanooga® Revolution Wireless, the waveform is limited to “Square Biphasic Symmetric – 1 pulse with a 100usec
interval”. The output waveforms are constant current, square shape and zero net DC.

SPECIFICATION
14
Parameters Min Typ Max Units Conditions
Output Voltage 189 195 [V] Body load, Iout = 120 [mA]
Output Current Impulse 0 120 [mA] Body load = 180 [Ω] + (1 [k Ω] // 47 [nF])
Output Current Resolution 0.25 [mA]
Output Current Precision -3 3 [%] 0 < Iout < 120 [mA]
Impulse Width 30 400 [µs]
Impulse Width Precision -5 5 [%]
Impulse Frequency 1 150 [Hz]
Impulse Frequency Precision -10 10 [%]
Output Power Dissipation 1.5 [W]
REMOTE CONTROL SPECS
Parameters Min Typ Max Units Conditions
Height 9 11 [cm]
Width 4.5 7 [cm]
Depth 0.7 2 [cm]
Weight 70 120 [g] With Battery
Continuous Voltage Input 3.7 [V]
Continuous Current Input 0.22 [A]
Battery autonomy
The battery has enough capacity for 6 hours of intensive usage during the first year of usage of the device. During these 6
hours, the backlight is on at 100% intensity for 3 hours and reduced intensity for the remaining 3 hours. These
performances are reachable after 90 minutes of charge on the docking (i.e. at full charge current).

SPECIFICATION
15
MODULE SPECS
Parameters Min Typ Max Units Conditions
External Diameter per Pod 5.3 6 [cm]
Height per Pod 2 [cm]
Weight ; Battery Pod 30 [g]
Weight ; Stimulation Pod 30 [g]
Weight per Module ( 2 pods : batpod
+ stimpod)
65 [g]
Resistance per Wire 50 75 [mΩ]
Inductance per Wire 1 [µH]
Frequency = 500 [kHz] / Impedance with
cable arranged to make 2 loops
Cable (3x wire) Outer Diameter 3 [mm]
Continuous Voltage Input 3.08 3.7 4.25 [V]
Continuous Current Input 0.45 [A] Output power of 0.7 [W]
Battery autonomy
When it’s fully charged, the battery of the module has an autonomy of 430 [mA*h]. With it it’s possible to make 8x VMS-
Muscle Atrophy at 20mA intensity.
DOCKING STATION SPECS
Parameters Min Typ Max Units Conditions
Height 20 22 [cm] Docking station tablet + subassembly
Width 26.5 27.5 [cm] Docking station tablet + subassembly
Depth 24 27 [cm] Docking station tablet + subassembly
Weight 2400 [g] Docking station tablet + subassembly
Charging Current 3.5 [A] 1 remote + 4 modules in charge
Stand-by Current 40 80 [mA]
Charging Total Voltage 4.75 5 5.25 [V] Charging current = 3.5 [A]
Remote Charging Voltage 4.6 [V] Charging only the remote, Ich = 1.5 [A]
Module Charging Voltage 4.6 [V] Charging only one module, Ich = 0.5 [A]

SPECIFICATION
16
Safety
To guarantee your safety, the Revolution Wireless has been designed, manufactured, and distributed in compliance with
the requirements of IEC 60601-1, IEC 60601-1-2, IEC 60601-1-4, IEC 60601-2-10, IEC 60950-1, IEC 61000-3-2, IEC 61000-3-3,
CISPR 22 and CISPR 24.
The Revolution Wireless also complies with the IEC 60601-1 standard on general safety requirements for electro-medical
devices, the IEC 60601-1-2 standard on electromagnetic compatibility, and the IEC 60601-2-10 standard on particular safety
requirements for nerve and muscle stimulators.
The markings on the unit are your assurance of its conformity to the highest applicable standards of medical equipment
safety and electromagnetic compatibility. One or more of the following markings may appear on the device.
Meets Directive 93/42/EEC, Complies with IEC
60601-1, IEC 60601-1-2, IEC 60601-2-10.
Non-ionizing radiation.
Electro Magnetic Compatibility. Keep away from sunlight.
Meets Restriction of Hazardous Substances
Directive 2002/95/EC.
Keep dry.
UL94 Standards: Inflammability of plastic parts. All units are latex-free.
The Wireless Professional unit is a class IIa
device with internal electric power and type BF
applied parts.
Council Directive 2002/96/EC concerning
Waste Electrical and Electronic Equipment
(WEEE). Indicates a requirement not to
dispose of WEEE as municipal waste.
Name and address of the authorized
representative in the European Community.
Name and address of the manufacturer
and manufacturing date.
The On/Off button is a multi-function button.
Caution / Follow the user manual or
operating instructions.

NOMENCLATURE & PARTS
17
This section offers a global view of the manufacturing of the product (internal and external views). It contains information
about every part of the Chattanooga® Revolution Wireless device (nomenclature and article code).
WARNING: The information and the figures of this chapter are only here to give a global knowledge of the product. Keep in
mind that it is not allowed, in any case, to open the remote or the modules of the Chattanooga® Revolution Wireless
device.
COMPLETE SET 4 CHANNELS REVOLUTION WIRELESS
The nomenclature below indicates the general locations of the components of the complete Chattanooga Revolution
Wireless set.
1
2
3
4
5
6/7/8
9
10
11
12
13
14
1
Note: Final accessories may differ from the picture

NOMENCLATURE & PARTS
18
N°
Article code
Item
Qty
1 101230
CHATT REVOLUTION WIRELESS REMOTE
CONTROL
1
2 984364
CHATT REVOLUTION WIRELESS
STIMULATION MODULE
4
3 683164
DOCKING STATION CHATT REVOLUTION
WIRELESS
1
4
649028
Adapter 5V 3,5A US PLUG
1
5
601163
USB CABLE
1
6 42204
BAGS OF SMALL ELECTRODES
2
7
42203
BAGS OF LARGES ELECTRODES (2 snaps)
2
8
42223
BAGS OF LARGES ELECTRODES (1 snap)
2
9 885882
CHATT REVOLUTION WIRELESS QUICK
START GUIDE & WARNINGS EN-SP
1
10 680050
CHATT REVOLUTION WIRELESS
TRANSPORTATION CASE
1
11 5529050
CHATTANOOGA LANYARD FOR
PROTECTION SLEEVE
1
12
5529024
WPRO RC PROTECTION SLEEVE WHITE
1
13 13-8890
CHATT REVOLUTION WIRELESS USB STICK
ASSEMBLY
1
14 5529220 COLOR PLASTIC RINGS 1

NOMENCLATURE & PARTS
19
REMOTE CONTROL
The nomenclature below indicates the general locations of the components of the remote. Know the components and their
functions before performing any operation of service to the units.
External components
N°
Article code
Item
Qty
1 101230 CHATT REVOLUTION WIRELESS REMOTE CONTROL 1
2
-
WS REMOTE ON/OFF KEY
1
3
-
WS USB PORT
1
4
-
WS REMOTE CHANNEL KEYS
1
5
-
WS 4 DIR .NAV. KEY
1
6 -
WS ENTER BUTTON
1
1
2
3
4
5
6