Chattanooga Vectra Neo Clinical Therapy System Cart User manual

Neo Clinical
Therapy
System Cart
Manual
Installation
Instructions
DJO , LLC
A DJO Global Company
1430 Decision Street
Vista, CA 92081-8553
T: 1-800-592-7329 USA
T: 1-760-727-1280
F: 1-760-734-5608
DJOGlobal.com
© 2013 DJO, LLC. All rights reserved.
Neo Therapy System Cart Manual
13-7781 Rev C
For complete User Operating Instructions,
including Cautions, Warnings, Dangers,
Indications, and Contraindications, refer to the
User’s Manuals.
• Domestic Market, US only, refer toVectra Neo
Clinical Therapy System User Manual, Item
#13-7646 (CDVersion, item #13-7647).
• International Market, refer to Intelect Neo
Clinical Therapy System User Manual, Item
#13-7651 (CDVersion, item #13-7652).
• To obtain a copy, contact your local
representative or DJO Customer Care.

2
Neo Clinical Therapy System Cart Manual
Modules
• Stimulation Channel 1/2
• Stimulation Channel 1/2 + sEMG
• Stimulation Channel 3/4
• Laser
• Ultrasound
• Vacuum (International Only)
Throughout these instructions the terms “left” and “right”
referring to the machine sides are from the perspective of
a user standing in front of the unit.
The Neo Clinical Therapy System allows installation of
optional modality modules (except Vacuum module)
by the user. Specically designed for use with the Neo
Clinical Therapy System, these modules congure the
system to meet virtually every therapeutic need that a
clinician may have. The components of the Neo Clinical
Therapy System are shown below.
Items included with the Cart:
• Three removable drawers
• Left and Right side legs with casters
• Allen wrench (1), Allen bolts (6), and Washers (6)
NOTE: The Neo Clinical Therapy System, when ordered
as a Tabletop System, without cart, is assembled with
Base, as shown below. When ordered with the cart, the
assembly required is the installation of the cart.
Head
COMPONENTS
Base
Cart with Neo SystemCart

3
Neo Clinical Therapy System Cart Manual
HEAD TO CART ASSEMBLY
The optional Therapy System Cart is designed for use with
the Neo Therapy System only and allows the user to easily
transport the System from patient to patient within the
clinic as well as store accessories, supplies, and applicators
used for the various modalities of the System.
Tools required (not included): #2 Phillips screwdriver and
standard slotted screwdriver.
Remove the Neo Clinical Therapy System from the
shipping carton. Visually inspect for damage. Report any
damage to the carrier immediately.
To assemble the Neo Head to the Cart, follow these steps:
1. Power off device. Remove the power cord from the
rear of the device.
2. Remove the top drawer from the Cart. Pull the drawer
open. Press the plastic tabs on both drawer slides
simultaneously in opposite directions, as shown. Pull
the drawer completely out.
3. Remove the base from the head unit prior to placing
it on the cart. Do this by removing the four screws
from the underside of the base where they secure to
the Neo Head. Retain for use when attaching the Neo
Head to the Cart.
4. Place the Neo Head on the cart. Screen front should
be facing toward the drawers.
5. Fasten the Neo Head to the cart using four screws
removed in Step 3, as shown.
6. If desired, replace the closed Handles with the open
Handles. Each Handle is attached with four screws as
shown.
7. Reinstall the top drawer that was removed in Step 2.

4
Neo Clinical Therapy System Cart Manual
CART SPECIFICATIONS
Width Depth Height Weight
Head @ 45 degree with Base (Tabletop) 15.89”(40.3606 cm) 15.89”(40.3606 cm) 22.05”(56.007 cm) 20.7lb (9.389362 kg)
Cart Lowered (with casters) 23.94”(60.8076 cm) 26.19”(66.5226 cm) 27.41”(69.6214 cm) 29.4lb (13.33562 kg)
Cart Raised (with casters) 23.94”(60.8076 cm) 26.19”(66.5226 cm) 30.15”(76.581 cm)
Head and raised cart with screen @ 90deg 23.94”(60.8076 cm) 26.19”(66.5226 cm) 52.85”(134.239 cm) 48.9lb (22.18067 kg)
NEO LEG TO CART ASSEMBLY/ADJUSTMENT
The Neo Cart is shipped without the legs attached. To
install or adjust the leg assemblies onto the Neo Cart,
follow these steps:
Neo Leg to Cart assembly/Adjustment
Tools Required:
• 3/16” Allen Wrench (provided)
• Flat Washer ¼” Internal diameter, quantity 6,
(provided)
• Allen Bolts ¼-20 x 1-1/4”, quantity 6 (provided)
1. Remove the bottom drawer from the Cart. Pull the
drawer open. Press the plastic tabs on both drawer
slides simultaneously in opposite directions, as shown.
Completely pull the drawer out.
2. There are two Cart height adjustments. Standard
shown on the left and lowered, shown on the right.
For initial installation, determine the desired height.
3. Locate three Allen Bolts and washers for each leg,
left and right sides. Insert the bolts, by hand, in their
respective slots. Use the Allen wrench to secure the
legs.
NOTE: To Adjust Height at a later time, simply remove
the Allen Bolts, reposition the legs and insert the bolts.
4. Reinstall the Bottom Drawer.