Chauvet Professional Ovation E-260WW User manual

User Manual
*Lens tubes
sold separately

Edition Notes
Ovation E-260WW User Manual Rev. 9
Edition
Notes
The Ovation E-260WW User Manual includes a description, safety precautions, and installation,
programming, operation, and maintenance instructions for the Ovation E-260WW
as of the
release date of this edition.
Trademarks
CHAUVET, the Chauvet logo and Ovation E-260WW are registered trademarks or trademarks
of Chauvet & Sons LLC
. (d/b/a Chauvet and Chauvet Lighting) in the United States and other
countries. Other company and product names and logos referred to herein may be trademarks
of their respective companies.
Copyright Notice
The works of authorship contained in this manual, including, but not limited to, all design, text
and images are owned by Chauvet.
© Copyright 2020 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
Manual Use
Chauvet authorizes its customers to download and print this manual for professional information
purposes only. Chauvet expressly prohibits the u
sage, copy, storage, distribution, modification,
or printing of this manual or its content for an
y other purpose without written consent from
Chauvet.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing,
operating, or maintaining this product.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in all respects.
However, Chauvet assumes no responsibility and specifically disclaims any and all liability to
any party for any loss, damage or disruption caused
by any errors or omissions in this
document, whether such errors or omissions result from negligence, accident or any other
cause. Chauvet reserves the right to revise the content of this document without any obligation
to notify any person or company of such revision, however, Chauvet has no obligation to make,
and does not commit to make, any such revisions.
Document
Revision
Go to www.chauvetprofessional.com for the latest version.

Table of Contents
Ovation E-260WW User Manual Rev. 9 -i-
Table of Contents
1. Before You Begin ........................................................................................................................................ 1
What Is Included ........................................................................................................................................................... 1
Claims ..........................................................................................................................................................................................1
Manual Conventions ..................................................................................................................................................... 1
Symbols .......................................................................................................................................................................................1
FCC Compliance .......................................................................................................................................................... 1
Safety Notes ................................................................................................................................................................. 2
2. Introduction ................................................................................................................................................. 3
Description.................................................................................................................................................................... 3
Features........................................................................................................................................................................ 3
Lens Tube..................................................................................................................................................................... 3
Overview....................................................................................................................................................................... 4
Dimensions ................................................................................................................................................................... 5
3. Setup ............................................................................................................................................................ 6
AC Power...................................................................................................................................................................... 6
AC Plug........................................................................................................................................................................................6
Power Linking...............................................................................................................................................................................6
Fuse Replacement .......................................................................................................................................................................6
DMX Linking ................................................................................................................................................................. 7
DMX Personalities........................................................................................................................................................................ 7
Remote Device Management (RDM) ...........................................................................................................................................7
Master/Slave Connectivity............................................................................................................................................................7
Mounting ....................................................................................................................................................................... 8
Orientation ................................................................................................................................................................................... 8
Rigging.........................................................................................................................................................................................8
Procedure ....................................................................................................................................................................................8
Manual Beam Focus Control........................................................................................................................................................ 9
Rotating the Barrel Assembly....................................................................................................................................................... 9
Accessory Slot .............................................................................................................................................................................9
4. Operation ................................................................................................................................................... 10
Control Panel Description........................................................................................................................................... 10
Control Options........................................................................................................................................................... 10
Programming .............................................................................................................................................................. 10
Menu Map................................................................................................................................................................... 10
Menu Map (cont.)........................................................................................................................................................ 11
Configuration (Standalone)......................................................................................................................................... 12
Manual Static Mode ...................................................................................................................................................................12
Focus Mode ............................................................................................................................................................................... 12
Auto Programs ........................................................................................................................................................................... 12
Master/Slave ..............................................................................................................................................................................12
Dimmer Curve ............................................................................................................................................................................12
Dimmer Profiles.......................................................................................................................................................................... 12
LED Frequency ..........................................................................................................................................................................13
Fan Mode...................................................................................................................................................................................13
Back Light .................................................................................................................................................................................. 13
Run Time ................................................................................................................................................................................... 13
LED Time ................................................................................................................................................................................... 13
Software Information .................................................................................................................................................................. 13
RDM........................................................................................................................................................................................... 13

Table of Contents
-ii- Ovation E-260WW User Manual Rev. 9
Configuration (DMX) ................................................................................................................................................... 13
DMX Personalities......................................................................................................................................................................13
DMX Control ..............................................................................................................................................................................13
DMX Values................................................................................................................................................................ 14
6Ch ............................................................................................................................................................................................14
3Ch ............................................................................................................................................................................................14
2Ch ............................................................................................................................................................................................14
1Ch ............................................................................................................................................................................................14
5. Technical Information ............................................................................................................................... 15
Product Maintenance.................................................................................................................................................. 15
Technical Specifications .............................................................................................................................. 16
Returns........................................................................................................................................................... 17
Contact Us ..................................................................................................................................................... 18

Before You Begin
Ovation E-260WW User Manual Rev. 9 -1-
1. Before You Begin
What Is
Included
•Ovation E-260WW
•Neutrik powerCON power cord
•Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make sure all the parts are in
the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not Chauvet
. Failure to
report damage to the ca
rrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery.
Manual
Conventions
Convention Meaning
1–512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1–10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols
Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.
FCC
Compliance
This device complies with Part 15 Part B of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including inte
rference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

Before You Begin
-2- Ovation E-260WW User Manual Rev. 9
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this User
Manual will only apply to properly trained Chauvet certified technicians. Do not open the
housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety
•The luminaire should be positioned so that prolonged staring into the luminaire at a
distance closer than 2.3 m is not expected.
•If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a
special cord or cord exclusively available from the manufacturer or his service agent.
•The light source contained in this luminaire shall only be replaced by the manufacturer or
his service agent or a similar qualified person.
•The luminaire is intended for professional use only.
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting and
Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture. (IP20)
•Do not allow the product to remain pointed straight down.
•CAUTION: When transferring product from extreme temperature environments, (e.g. cold
truck to warm humid ballroom) condensation may form on the internal electronics of the
product. To avoid causing a failure, allow product to fully acclimate to the surrounding
environment before connecting it to power.
•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable.
•Use caution when loosening the barrel rotation knobs. If these knobs become too loose,
the barrel assembly may inadvertently separate from the light engine.
Power and
Wiring
•Always make sure you are connecting this product to the proper voltage in accordance with
the specifications in this manual or on the product’s specification label.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have the
damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your Chauvet product requires service, contact Chauvet
Technical Support.
Expected LED
Lifespan
Over time, use and heat will gradually reduce LED brightness. Clustered LEDs produce more
heat than single LEDs,
contributing to shorter lifespans if always used at full intensity. The
average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper
ventilation around the product, and limit the overall intensity.

Introduction
Ovation E-260WW User Manual Rev. 9 -3-
2. Introduction
Description
The Ovation E-260WW delivers an excellent white light with a warm color temperature and a
beautiful flat field. It also features standard beam shaping shutters, a gobo/effect slot and lens
barrels that are interchangeable with other popular ERS fixtures. Selectable dimming cu
rves
ensure smooth fading cues that intermix well with the output of conventional theatre ellipsoidals.
Features
•Warm white LED ERS-style lighting product
•Operating modes:
•1-channel: dimmer control
•2-channel: dimmer and fine dimmer control
•3-channel: dimmer, fine dimmer, and strobe control
•6-channel: dimmer, fine dimmer, strobe control, auto programs, auto speed, and
control
•Warm white ERS style fixture with output exceeding a tungsten 750w source
•Ultra smooth 16-bit dimming, and 8-bit dimming curves to complement any lighting scheme.
•Flat, even field of light for superior gobo projection
•RDM (Remote Device Management) for added flexibility
•Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
•Virtually silent operation for use in studio and theatre applications
•Works perfectly with industry standard lens tubes and accessories
Lens Tube
The following lens tubes are available for purchase.
•14° w/ Gel frame (7.5 in/191 mm accessories)
•19° w/ Gel frame (6.25 in/159 mm accessories)
•26° w/ Gel frame (6.25 in/159 mm accessories)
•36° w/ Gel frame (6.25 in/159 mm accessories)
•50° w/ Gel frame (6.25 in/159 mm accessories)
•15°–30° w/ Gel frame (7.5 in/191 mm accessories)
•25°–50° w/ Gel frame (7.5 in/191 mm accessories)

Introduction
-4- Ovation E-260WW User Manual Rev. 9
Overview
Pattern Holder Slot
(A-size holder for 3-in patterns
B
-size holder for 2.5-in and 2.75-in
patterns,
sold separately)
Beam Focus Knobs
Rear View
Side View
powerCON®
Output
powerCON®
Input
Menu Buttons
3- and 5-pin DMX In
3- and 5-pin DMX Out
Fuse Holder
Gel Frame
Holder
Display
Handle
Framing Shutter
(x 4)
Lens Tube
(sold separately)
Barrel
Rotation
Knobs
Barrel
Assembly
Light
Engine
Accessory
Slot

Introduction
Ovation E-260WW User Manual Rev. 9 -5-
Dimensions
6.7 in
171 mm
6.25 in
159 mm
Side View
Top View
6.9 in
174 mm
15 in
380 mm
7.1 in
180 mm
20.9 in
530 mm
8.7 in
222 mm
25.4 in
645 mm
12 in
305 mm

Setup
-6- Ovation E-260WW User Manual Rev. 9
3. Setup
AC Power
Each Ovation E-260WW has an auto-ranging power supply that works with an input voltage
range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each Ovation E-
260WW, refer to the label affixed to the product. You can also refer to the
Technical
Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, you may download Sizing Circuit Breakers from the Chauvet website
:
www.chauvetprofessional.com.
•Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The Ovation E-260WW comes with a power input cord terminated with a Neutrik powerCON A
connector on one end and an Edison plug on the other end (U.S. market). If the power input
cord that came with your product has no plug, or if yo
u need to change the Edison plug, use the
table below to wire the new plug.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Power Linking
The Ovation E-260WW supports power linking. You can power link up to 8 products at
120 V; up to 13 at 208 V; or up to 14 at 230 V.
This product comes with a power input cord. Power linking cables are available from Chauvet
for purchase.
Fuse
Replacement
1. Disconnect this product from the power outlet.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating
(T 3.15 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
Make sure to disconnect the product’s power cord before replacing a blown fuse. Always
replace the blown fuse with another of the same type and rating.

Setup
Ovation E-260WW User Manual Rev. 9 -7-
DMX Linking
You can link the Ovation E-260WW to a DMX controller using a 3- or 5-pin DMX connection. If
using other DMX-compatible products with the Ovation E-260WW
, you can control each
individually with a single DMX controller.
DMX
Personalities
The Ovation E-260WW uses the standard DMX data connection for the 1-, 2-, 3- and 6- channel
DMX modes.
•Refer to the Introduction chapter for a brief description of each DMX personality.
•Refer to the Operation chapter to learn how to configure the Ovation E-260WW to work in
these personalities.
•The DMX Values section provides you with detailed information regarding the DMX
personalities.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.
Remote Device
Management
(RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to
communicate bi-
directionally along existing DMX cabling. Check the DMX controller’s User
Manual or with the manufacturer as not all DMX
controllers have this capability. The
Ovation E-
260WW supports RDM protocol that allows feedback to make changes to
menu map options.
Master/Slave
Connectivity
The Master/Slave mode allows a single Ovation E-260WW (the “master”) to control the actions
of one or more Ovation E-260WW
products (the “slaves”) without the need of a DMX controller
to control the slaves. Once set and connected, the slaves will operate in unison with the master.
For instructions on connecting and configuring this product, see Master/Slave Mode.
DO NOT connect a DMX controller to products operating in Master/Slave mode. The DMX
controller signals may interfere with the signals from the master.
•The Operation section of this manual provides detailed instructions on how to
configure the master and slaves.
•If you are not familiar with or need more information about DMX standards, or the
DMX cables needed to link this product to a DMX controller, download the DMX
Primer from the Chauvet website: www.chauvetprofessional.com.

Setup
-8- Ovation E-260WW User Manual Rev. 9
Mounting
Before mounting this product, read and follow the Safety Notes. For our CHAUVET
Professional line of mounting clamps, go to http://trusst.com/products/.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
Chauvet recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for operation,
programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the product’s
weight. See the Technical Specifications for the weight-bearing requirements of this
product.
•When hanging this product, always secure to a fastening device using a safety cable. For
our CHAUVET Professional line of safety cables, go to http://trusst.com/products/.
Procedure
The Ovation E-260WW comes with a hanging/mounting bracket to which you can attach
mounting clamps. The bracket has 13-
mm holes, which are appropriate for this purpose. You
must supply your own mounting clamps, so be sure the clamps are capable of supportin
g the
weight of this product. Use at least one mounting point per product where necessary..
Mounting Diagram
Mounting Clamp
Overhead Mounting
Bracket
Adjustment
Hand Shank
Hanging/Mounting
Bracket
Safety Cable
Secure the safety
cable using the
passageway on the
top of the product
Alternative Yoke
Attachment
Alternate Short Mounting

Setup
Ovation E-260WW User Manual Rev. 9 -9-
Manual Beam Focus
Control
The Ovation E-260WW has a manual focus, which is adjusted as follows.
1. Locate the beam focus knobs at the top and bottom of the barrel assembly.
2. Loosen the knobs by turning them counter-clockwise.
3. Slide the lens tube forward or backward until you achieve the desired focus or beam
edge.
4. Tighten the knobs by turning them clockwise, which lock the lens tube’s position.
To avoid changing menu settings while focusing the Ovation E-260WW, press and
hold the <ENTER> button for 3 seconds. This will put the product in “Focus Mode”
by increasing the intensity to 100%. To exit out of focus mode, press <MENU>.
Rotating the Barrel
Assembly
The Ovation E-260WW allows manual rotation of the barrel assembly, as follows.
1. Locate the barrel rotation knobs at the top and bottom of the light engine.
2. Loosen the knobs by turning them counter-clockwise.
•Note: Do not remove the knobs.
3.
Rotate the barrel to the desired position, up to 25° in either direction from the centered
position.
4. Tighten the knobs by turning them clockwise, which lock the barrel’s position.
Make sure the barrel assembly is oriented with the pattern holder and a
ccessory
slots at the top of the product.
Accessory Slot
The Ovation E-260WW has an accessory slot, which holds a drop-in iris, a motorized
pattern device, or various other optional accessories (sold separately).
1. Loosen the thumbscrews on the slot cover.
•Note: Do not remove the thumbscrews.
2. Slide to cover forward.
3. Insert an accessory.
•Note: Make sure to insert the accessory correctly. For example, make sure the
iris handle extends upward from the slot.
4. Slide the cover back. Make sure any handles or adjustment tools that stick out the top
are able to function correctly.
5. Tighten the thumbscrews to secure the cover.
•When not using the accessory slot, replace and secure the slot cover to prevent
light leakage during operation.
•When obtaining any
optional accessories, be sure the items are compatible with
the Ovation E-260WW.
Thumbscrews
Accessory
Slot Cover
Sample
Drop-in Iris
Iris Handle

Operation
-10- Ovation E-260WW User Manual Rev. 9
4. Operation
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value in to the current function
<UP>
Navigates upward through the menu list or increases the numeric
value when in a function
<DOWN>
Navigates downward through the menu list or decreases the numeric
value when in a function
Control
Options
Set the Ovation E-260WW starting address in the 001–512
DMX range. This enables control of
up to 85 products in the 6-channel 6CH personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main level
and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on the
display. Press <ENTER> to select. This will take you to the first programming level for that
option.
•To select an option or value within the current programming level, press <UP> or <DOWN>
until the option shows on the display. Press <ENTER> to select. In this case, if there is
another programming level, you will see that first option, or you will see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.
Menu Map
Main Level
Programming Levels
Description
DMX Address <001–512>
Selects DMX address (highest channel
restricted to personality chosen)
DMX Channel
1Ch
1-channel: dimmer
2Ch
2-channel: 16-bit dimmer
3Ch
3-channel: 16-bit dimmer, strobe
6Ch
6-channel: 16-bit dimmer, strobe, auto
programs, auto speed, control
Static
Dimmer
0–255
Controls intensity
Strobe
Controls strobe rate
Auto Show
Auto 1
<1–100> Selects automatic programs and auto
program speed
Auto 2
Auto 3
Auto 4
Master/Slave
Master
DMX mode (Master)
Slave
Slave mode
Dimmer Curve
SCurve
Sets the dimmer curve
Linear
Square
Inverse Square
Dimmer Mode
Off
No dimmer
Dimmer 1–3
Dimming curves Dimmer 1 (fast) to
Dimmer 3 (slow)

Operation
Ovation E-260WW User Manual Rev. 9 -11-
Menu Map (cont.)
Main Level
Programming Levels
Description
LED Frequency
600Hz
Selects the PWM output frequency
1200Hz
2000Hz
4000Hz
6000Hz
25KHz
Fan Mode
Auto
Sets the fan to auto mode
On
Sets the fan to always on
Off
Sets the fan to always off
Silent
Sets the fan to silent
Back Light
10S
Turns off display backlight after 10 sec of
inactivity
30S
Turns off display backlight after 30 sec of
inactivity
2Min
Turns off display backlight after 2 mins of
inactivity
Always On
Display backlight always on
Information
Fixture Hours _ _ _ _H
Shows total hours the product has been
powered on
LED Hours _ _ _ _H
Shows total hours the LED has been
powered on
Version
V_._
Shows installed software version
UID:
_ _ _ _ _ _ _ _ _ _ _ _
Shows product UID

Operation
-12- Ovation E-260WW User Manual Rev. 9
Configuration
(Standalone)
Use standalone configuration to operate the product without a DMX controller.
Manual Static
Mode
The Manual Static mode allows for manual control of intensity and strobe rate without a DMX
controller.
1. Go to the Static main level.
2. Select the Dimmer programming level.
3. Select the desired intensity value 0–255 (0–100%).
4. Go to the Strobe programming option.
5. Select the desired Strobe rate value 0–255 (0–25 Hz).
Focus Mode
Focus mode allows for focusing of the Ovation E-260WW without changing any menu settings.
1. Press and hold <ENTER> for 3 seconds. The intensity will increase to 100%.
2. Press <MENU> to exit to previous settings.
Auto Programs
Auto programs allow for standalone dynamic mixing without a DMX controller.
1. Go to the Auto Show main level.
2. Select the desired auto (Auto 1–4)
3. Select the desired auto program speed (1–100)
You cannot edit any of the auto programs (Auto 1–4).
Master/Slave
The Master/Slave mode allows a group of Ovation E-260WWs (the slaves) to simultaneously
duplicate the output of another Ovation E-260WW (the master) without a DMX controller.
1. Set each of the slaves:
a. Go to the Master/Slave main level.
b. Select Slave.
2. Set the master:
a. Go to the Master/Slave main level.
b. Select Master.
•The master is the one that runs a program whether in Auto Show or Static modes.
•Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
•The master should be the first product in the daisy chain.
Dimmer Curve
To set the dimmer curve, follow the instructions below:
Go to the Dimmer Curve main level.
Select the desired option (SCurve, Linear, Square, or Inverse Square).
Dimmer Profiles
This setting determines how fast the output of the Ovation E-260WW changes when you modify
the values of the white, and dimmer faders. This setting provides four different options to
simulate the dimming curve of an incandescent lighting product.
1. Go to the Dimmer Mode main level.
2. Select a dimmer curve (Off, Dimmer 1, Dimmer 2, or Dimmer 3).
Off:
The output is proportional (linear) to the dimmer and white channel values.
Dimmer 1–3:
The output follows the dimmer and White channel values based on the
corresponding dimmer curve, Dimmer 1 being the fastest and Dimmer 3 the
slowest.
For optimum control of the 16-bit dimming channels in the 3Ch, and 6Ch personalities,
be sure that the dimming curves in Dimmer Mode are set to Off.

Operation
Ovation E-260WW User Manual Rev. 9 -13-
LED Frequency
This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the
Ovation E-260WW.
1. Go to the LED Frequency main level.
2. Choose an output frequency. (600Hz, 1200Hz,2000Hz,4000Hz, 6000Hz, or 25KHz)
Fan Mode
This option toggles the fan speed from being always on and auto control based on the product’s
temperature.
1. Go to the Fan Mode main level.
2. Select a fan mode (Auto, On, Off, or Silent).
Back Light
This setting allows you to set the amount of time the backlight on the Ovation E-260WW’s
display stays on after the last button is pressed on the control panel.
1. Go to the Back Light main level.
2. Select Always On (remains on), 10S (10 seconds), 30S (30 seconds), or 2Min (2 minutes).
Run Time
This option show how many total hours the product has been on.
1. Go to the Information main level.
2. Select Fixture Hours and the amount of hours will show on the screen.
LED Time
This option show how many total hours the LED has been powered on.
3. Go to the Information main level.
Select LED Hours and the amount of hours will show on the screen.
Software
Information
This option shows what version of software the Ovation E-260WW is running.
1. Go to the Information main level.
2. Select Version and the version number will show on the screen.
RDM
This option shows the product’s UID #. The UID # is used when using the RDM functionality of
this product.
1. Go to the Information main level.
2. Select UID: and the number will show on the screen.
Configuration
(DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX
Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the DMX Channel main level.
2. Select the desired personality (1Ch, 2Ch, 3Ch, or 6Ch).
•See the DMX Values section for the highest starting address you can select for each
personality.
•Make sure that the starting addresses on the various products do not overlap due to
the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All
products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the running mode:
a. Go to the Master/Slave main level.
b. Select the Master programming level.
3. Set the starting address:
a. Go to DMX Address main level.
b. Select the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX Personality
DMX Address
DMX Personality
DMX Address
1Ch
508
2Ch
503
6Ch
506
3Ch
500

Operation
-14- Ovation E-260WW User Manual Rev. 9
DMX Values
6Ch
Channel Function Value Percent/Setting
1
Dimmer
000 255
0–100%
2
Dimmer Fine
000 255
0–100%
3 Strobe
000010
011255
No function
Strobe (slow to fast)
4 Auto Programs
000

010
011070
071130
131190
191255
No function
Auto 1
Auto 2
Auto 3
Auto 4
5
Auto Speed
000255
Slow to fast
6 Control
(hold for 3 seconds)
000

007
008015
016023
024031
032039
040047
048055
056063
064071
072079
080087
088095
096103
104111
112255
No function
Dimmer reset
S-curve dimmer
Linear dimmer
Square dimmer curve
Inverse square dimmer curve
Dimmer speed mode off
Dimmer speed mode 1 (fastest)
Dimmer speed mode 2
Dimmer speed mode 3 (slowest)
Fan auto
Fan on
Fan off
Fan silent
Reserved for future use
3Ch
Channel
Function
Value
Percent/Setting
1
Dimmer
000 255
0–100%
2
Dimmer Fine
000 255
0–100%
3 Strobe
000

010
011255
No function
Strobe (slow to fast)
2Ch
Channel
Function
Value
Percent/Setting
1
Dimmer
000 255
0–100%
2
Dimmer Fine
000 255
0–100%
1Ch
Channel
Function
Value
Percent/Setting
1
Dimmer
000 255
0–100%

Technical Information
Ovation E-260WW User Manual Rev. 9 -15-
5. Technical Information
Product
Maintenance
To maintain optimum performance and minimize wear, clean this product frequently. Usage and
environment are contributing factors in determining the cleaning frequency.
Clean this product at least twice a month. Dust build-up reduces light output
performance and
can cause overheating. This can lead to reduced light source life and increased mechanical
wear.
To clean your product:
1. Unplug the product from power.
2. Wait until the product is at room temperature.
3. Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the
external vents.
4. Clean all external surfaces with a mild solution of non-ammonia glass cleaner or isopropyl
alcohol.
5. Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
6. Wipe any dirt or grime to the outside edges of the lens surface.
7. Gently polish the lens surfaces until they are free of haze and lint.
Always dry the external surfaces thoroughly and carefully after cleaning them.
Do not spin the cooling fans while blowing compressed air into them.

Technical Specifications
-16- Ovation E-260WW User Manual Rev. 9
Technical Specifications
Dimensions
and Weight
Length Width Height Weight
19.49 in (495 mm)
11.22 in (285 mm)
19.17 in (487 mm)
15.4 lb (7.1 kg)
Note: Dimensions in inches are rounded.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100–240 VAC, 50/60 Hz
Auto-ranging
Parameter 120 VAC, 60 Hz 208 V, 60 Hz 230 VAC, 50 Hz
Consumption
209 W
206 W
204 W
Current
1.7 A
1.0 A
1.0 A
Power linking current
(products)
13.6 A (8 products)
13.6 A (13 products)
13.6 A (14 products)
Fuse/Breaker
T 3.15 A, 250 V
T 3.15 A, 250 V
T 3.15 A, 250 V
Power I/O
U.S./Canada
Worldwide
Power input connector
Neutrik powerCON A
Neutrik powerCON A
Power output connector
Neutrik powerCON B
Neutrik powerCON B
Power cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
230 W
50,000 hours
Color Quantity Current
Warm White
1
3.6 A
Photometrics
Parameter
14° Lens
19° Lens
26° Lens
36° Lens
50° Lens
15°–30° Lens
25°–50° Lens
Illuminance @ 5 m
13,439 lx
9,256 lx
6,910 lx
4,053 lx
1,703 lx
16,827 lx
10,626 lx
7,210 lx
3,295 lx
Lumens
N/A
7,587
10,284
10,121
9,655
N/A
N/A
N/A
N/A
Beam angle
11°
13°
16°
20°
28°
12°
14°
21°
22°
Field angle
14°
18°
25°
34°
50°
15°
29°
26°
46°
Thermal
Max. External Temperature Cooling System
113 °F (45 °C)
Fan-Assisted Convection
DMX
I/O Connectors
Connector Type
Channel Range
3- and 5-pin XLR
Sockets
1, 2, 3, 6
Ordering
Product Name
Item Name
Item Code
UPC Number
Ovation E-260WW
OVATIONE260WW
03121186
781462215347