Chauvet COLORado 2-Quad Zoom IP User manual

User Manual

Edition Notes
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Edition
Notes
The COLORado™ 2-Quad Zoom Tour
User Manual Rev. 1 covers the description, safety
precautions, installation, programming, operation, and maintenance of the COLORado™
2-Quad Zoom Tour. CHAUVET® released this edition of the COLORado™ 2-Quad Zoom Tour
User Manual in April 2014.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name and the dotted
triangle, and all other trademarks in this manual pertaining to services, products, or marketing
statements (example: It’s Green Thinking™) are owned or licensed by CHAUVET®. Any other
product names, logos, brands, company names, and other trademarks featured or referred to
within this document are the property of their respective trademark holders.
Copyright Notice
CHAUVET® owns the content of this User Manual in its entirety, including but not limited to
pictures, logos, trademarks, and resources.
© Copyright 2014 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Use
CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the u
sage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose without
written consent from CHAUVET®.
Document
Printing
For better results, print this document in color, on letter size paper (8.5 x 11 in), double-
sided. If
using A4 paper (210 x 297 mm), configure your printer to scale the content accordingly.
Intended
Audience
Any person in charge of installing, operating, and/or maintaining this product should completely
read through the guide that shipped with the product, as well as this manual, before installing,
operating, or maintaining this product.
Disclaimer
CHAUVET® believes that the information contained in this manual is accurate in all respects.
However, CHAUVET® assumes no responsibility for any errors or omissions in this document.
CHAUVET® reserves the right to revise and make changes to the content of this document
without obligation that CHAUVET® notify any person or company of such revision or changes.
This does not in any way constitute a commitment by CHAUVET® to make such changes.
CHAUVET® may issue a revision of this manual or a new edition to incorporate such changes.
Document
Revision
The COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 is the first edition of this manual. Go
to www.chauvetprofessional.com for the latest version.
Author
Date
Editor
Date
D. Couppe
4/17/14
A. Leon
4/22/14

Table of Contents
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -i-
Table of Contents
1. Before You Begin......................................................................................................................................1
What Is Included...........................................................................................................................................................1
Claims..........................................................................................................................................................................................1
Manual Conventions ....................................................................................................................................................................1
Symbols.......................................................................................................................................................................................1
Product At A Glance .....................................................................................................................................................2
Safety Notes .................................................................................................................................................................2
Personal Safety............................................................................................................................................................................2
Mounting And Rigging..................................................................................................................................................................2
Power And Wiring ........................................................................................................................................................................2
Operation.....................................................................................................................................................................................2
Expected LED Lifespan................................................................................................................................................2
2. Introduction...............................................................................................................................................3
Description....................................................................................................................................................................3
Features........................................................................................................................................................................3
Overview.......................................................................................................................................................................4
Dimensions...................................................................................................................................................................5
3. Setup..........................................................................................................................................................6
AC Power......................................................................................................................................................................6
AC Plug........................................................................................................................................................................................6
Power Linking ...............................................................................................................................................................7
DMX Linking..................................................................................................................................................................7
DMX Personalities........................................................................................................................................................................7
Master/Slave Connectivity............................................................................................................................................................7
Mounting.......................................................................................................................................................................8
Orientation ...................................................................................................................................................................................8
Rigging.........................................................................................................................................................................................8
Procedure ....................................................................................................................................................................................8
4. Operation...................................................................................................................................................9
Control Panel Description.............................................................................................................................................9
Control Options.............................................................................................................................................................9
Programming ................................................................................................................................................................9
Menu Map...................................................................................................................................................................10
Menu Map (Cont.).......................................................................................................................................................11
Configuration (Standalone).........................................................................................................................................12
Auto Programs...........................................................................................................................................................................12
Edit Custom Programs..............................................................................................................................................................12
Master/Slave..............................................................................................................................................................................12
Color Settings.............................................................................................................................................................................12
Dimmer Curves..........................................................................................................................................................................13
Curve Settings............................................................................................................................................................................13
Control Panel Lock.....................................................................................................................................................................13
Passcode...................................................................................................................................................................................13
Program Upload.........................................................................................................................................................................13
Reset..........................................................................................................................................................................................14
Whites Setting............................................................................................................................................................................14
White Calibration........................................................................................................................................................................14
Static Color ................................................................................................................................................................................14
TOUR Notes ...............................................................................................................................................................15
Master Dimmer...........................................................................................................................................................................15
Red, Green, Blue, And White Color Selection............................................................................................................................15
Color Macros..............................................................................................................................................................................15
Strobe ........................................................................................................................................................................................15

Table of Contents
-ii- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Auto/Custom..............................................................................................................................................................................15
Dimmer Speed...........................................................................................................................................................................15
Configuration (DMX)...................................................................................................................................................16
DMX Personalities......................................................................................................................................................................16
DMX Control...............................................................................................................................................................................16
Loss Of Signal Setting................................................................................................................................................................16
Zoom Limit Settings ...................................................................................................................................................................16
DMX Values................................................................................................................................................................17
DMX Values (Cont.)....................................................................................................................................................18
DMX Values (Cont.)....................................................................................................................................................19
DMX Values (Cont.)....................................................................................................................................................20
DMX Values (Cont.)....................................................................................................................................................21
DMX Values (Cont.)....................................................................................................................................................22
DMX Values (Cont.)....................................................................................................................................................23
5. Technical Information.............................................................................................................................24
Product Maintenance..................................................................................................................................................24
6. Technical Specifications.........................................................................................................................25
Returns .......................................................................................................................................................................26
Contact Us..................................................................................................................................................26

Before You Begin
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -1-
1. BEFORE YOU BEGIN
What Is
Included
•COLORado™ 2-Quad Zoom Tour
•Neutrik® powerCON® power cord
•Gel frame holder (9 in/229 mm accessories)
•Gel frame
•Safety cable
•Warranty card
•
Quick Reference Guide
Claims
Carefully unpack the product immediately and check the box to make
sure all the parts are in
the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not CHAUVET®. Failure
to report damage to the carrier immediately may invalidate your claim. In addition, keep the box
and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Manual
Conventions
Convention
Meaning
1–512
A range of values in the text
50/60
A set of mutually exclusive values in the text
<SET>
A button on the product’s control panel
Settings
A product function or a menu option
MENU>Settings
A sequence of menu options
1–10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to be entered or selected in a menu
Symbols
Symbols Meaning
Critical installation, configuration, or operation information. Failure to
comply with this information may cause the product not to work,
damage third-party equipment, or cause harm to the operator.
Important installation or configuration information. Failure to comply
with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-
A digital data
transmission protocol.

Before You Begin
-2- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Product At A
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-Ranging Power
Supply
P
Sound-Activated
x
Replaceable Fuse
x
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Read all the following Safety Notes before working with this product. These notes include
important information about the installation, usage, and maintenance of this product.
This product contains no user-serviceable parts. Any reference to servicing in this
User Manual will only apply to properly trained CHAUVET® certified technicians. Do
not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this product.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
•Do not touch this product’s housing during operation because it may be very hot.
Mounting And
Rigging
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture. (IP20)
•Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from
adjacent surfaces.
•Make sure there are no flammable materials close to this product while it is operating.
•When hanging this product, always secure to a fastening device using a safety cable
(included).
Power And
Wiring
•Always make sure you are connecting this product to the proper voltage in accordance
with the specifications in this manual or on the product’s specification label.
•Never connect this product to a dimmer pack or rheostat.
•Never disconnect this product by pulling or tugging on the power cable.
Operation
•Do not operate this product if you see damage on the housing, lenses, or cables. Have
the damaged parts replaced by an authorized technician at once.
•Do not cover the ventilation slots when operating to avoid internal overheating.
•The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a
higher temperature.
•In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan LEDs gradually decline in brightness over time, mostly because of heat. Packaged in clusters,
LEDs exhibit higher operating temperatures than in ideal, single-LED conditions. For this
reason, using clustered LEDs at their fullest intensity significantly reduces the LEDs’ lifespan.
Under normal conditions, this lifespan can be 40,000 to 50,000 hours. If extending this
lifespan is vital, lower the operating temperature by improving the ventilation around the
product and reducing the ambient temperature to an optimal operating range. In addition,
limiting the overall projection intensity may also help to extend the LEDs’ lifespan.

Introduction
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -3-
2. INTRODUCTION
Description
The COLORado™ 2-Quad Zoom Tour is a high-power quad-color (RGBW)
LED wash product
with color mixing and zoom control. This product consists of a single module that
houses the
internal power supply, the control panel, the LED drivers, the LED boards, and motorized moving
lenses, as well as the power and signal connectors. The COLORado™ 2-
Quad Zoom Tour
features a variable zoom, which enables the user to change the bea
m angle of the unit via DMX
or control panel, and one double-bracketed
yoke that can serve as a floor mount or hanging
support bracket.
Features
•3-, 4-, 5-, 6-, 7-, 12-, or 17-channel quad-color LED wash product
•Operating modes:
•3-channel: RGB control
•3-channel: HSV control
•4-channel: RGB, dimmer
•4-channel: RGBW
•5-channel: RGBW, dimmer
•6-channel: RGBW, dimmer, strobe
•7-channel: RGBW, dimmer, zoom, zoom reset
•12-channel: RGBW, dimmer, strobe, color macro, auto/custom, dimmer speed, auto
speed, zoom, zoom reset
•17-channel: 16-bit RGBW and dimmer; strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
•17-channel: 16-bit RGBW and dimmer; strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
•RGBW color mixing via DMX or manually
•Zoom control via DMX or manually
•Color temperature presets 3200 to 10000 K
•Built-in auto and custom programs recalled via DMX and Master/Slave
•16-bit dimming of individual colors as well as master dimmer
•Five distinct dimming curves for programming versatility
•Color macros with included speed adjustment
•Double-bracketed yoke doubles as a floor stand
•Neutrik® powerCON® power input/output connections
•3-pin and 5-pin DMX input/output connections
•LED display with passcode protection

Introduction
-4- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Overview
Power Out
DMX Out
DMX In
Control Panel
Front View
Rear View
Side View
Bracket Adjustment
Knob
Double-
Bracketed Yoke
Safety Cable Loop
Power In
DMX In
DMX Out
Top View

Introduction
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -5-
Dimensions
11.1 in
283 mm
11.1 in
283 mm
9.3 in
236 mm
13.8 in
348 mm

Setup
-6- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
3. SETUP
AC Power
Each COLORado™ 2-Quad Zoom Tour has an auto-ranging power supply that works with an
input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for
each COLORado™ 2-Quad Zoom Tour, refer to the label affixed to the product. You can also
refer to the Technical Specifications chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, you may download Sizing Circuit Breakers from the CHAUVET® website
:
www.chauvetlighting.com/download/pro.
Always connect this product to a protected circuit with an appropriate electrical ground
to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
The COLORado™ 2-Quad Zoom Tour comes with a
power input cord terminated with a
Neutrik® power
CON® connector on one end and an Edison plug on the other end
(U.S. market). If the power input cord that came with your product has no plug, or if you need to
change the Edison plug, use the table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green

Setup
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -7-
Power Linking
The COLORado™ 2-Quad Zoom Tour supports power linking. You can power link up to
5 products at 120 V; up to 10 at 208 V; or up to 10 at 230 V.
This product comes with a power input cord. Power linking cables are available from
CHAUVET® for purchase.
DMX Linking
You can link the COLORado™ 2-Quad Zoom Tour to a DMX controller using a 3- or 5-pin
DMX connection. If using other DMX-compatible products with the COLORado™ 2-
Quad
Zoom Tour, you can control each individually with a single DMX controller.
DMX Personalities
The COLORado™ 2-Quad Zoom Tour uses the standard DMX data connection for the
TOUR, TR16, STD.Y, ARC.1, AR1.D, ARC.2, AR2.D, AR2.S, AR2.Z, and HSV DMX
modes.
•Refer to the Introduction chapter for a brief description of each DMX personality.
•Refer to the Operation chapter to learn how to configure the COLORado™ 2-Quad
Zoom Tour to work in these personalities.
•The DMX Values section provides you with detailed information regarding the DMX
personalities.
Master/Slave
Connectivity
The Master/Slave mode allows a COLORado™ 2-Quad Zoom Tour
(the master) to
control one or more COLORado™ 2-Quad Zoom Tours (the slaves
) without a DMX
controller. One COLORado™ 2-Quad Zoom Tour becomes the master when running an
Auto or Custom program, or by being in a Static mode.
You must configure each slave’s control panel to operate in Slave
mode. During
Master/Slave operation, the slaves will operate in unison with the master.
DO NOT connect a DMX controller to products operating in Master/Slave mode.
The DMX controller signals may interfere with the signals from the master.
The Operation section of this manual provides detailed instru
ctions on how to configure
the master and slaves.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the CHAUVET® website:
www.chauvetlighting.com/download/pro.

Setup
-8- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Mounting
Before mounting this product, read and follow the Safety Notes.
For our CHAUVET® line of
mounting clamps, go to http://trusst.com/productcategory/base-plates-accessories-clamps/.
Orientation
Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging
CHAUVET® recommends using the following general guidelines when mounting this product.
•When selecting an installation location, consider easy access to this product for operation,
programming adjustments, and routine maintenance.
•Make sure to mount this product away from any flammable material as indicated in the
Safety Notes.
•Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
•If hanging this product, make sure that the mounting location can support the product’s
weight. See the Technical Specifications for the weight-bearing requirements of this
product.
•When hanging this product, always secure to a fastening device using a safety cable
(such as CH-05 from CHAUVET®).
Procedure
The COLORado™ 2-Quad Zoom Tour comes with a double-bracketed yoke
to which you can
either attach mounting clamps for hanging or simply use as a floor stand. You must supply your
own mounting clamps. Make sure the clamps (such as CLP-15 from CHAUVET®)
are capable
of supporting the weight of this product. Use at least one mounting point per product.
Mounting Diagram
Floor Mounting
Overhead Mounting
Mounting Clamp
Safety Cable

Operation
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -9-
4. OPERATION
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently
selected value in to the current function
<UP>
Navigates upward through the menu list or increases the numeric
value when in a function
<DOWN>
Navigates downward through the menu list or decreases the
numeric value when in a function
Control Options
You can set the COLORado™ 2-Quad Zoom Tour starting address in the 001–512
DMX
range. This enables control of up to 30 products in the 17-channel TR16 or STD.Y
personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main
level and a variable number of programming levels for each option.
•To go to the desired main level, press <MENU> repeatedly until the option shows on
the display. Press <ENTER> to select. This will take you to the first programming
level for that option.
•To select an option or value within the current programming level, press <UP> or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option, or you will
see the selected value.
•Press <MENU> repeatedly to exit to the previous main level.

Operation
-10- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Menu Map
Main Level Programming Levels Description
STAT
R.
000–255 Combines red, green, blue, and white to
make a custom color (0–100%)
G.
B.
W.
Z.
Changes the beam angle (zoom)
S. 00–20
Selects the strobe frequency
(0–20 Hz)
AUTO
AT.
01–10
10 automatic programs
PR.
C1–10
10 customizable programs
RUN
DMX
DMX mode
SLAV
Master/Slave mode
DMX
D.
001–512
Selects the DMX starting address
PERS
TOUR
12-channel: RGBW, dimmer, strobe, color
macro, auto/custom, dimmer speed, auto
speed, zoom, zoom reset
TR16
17-channel: 16-bit RGBW and dimmer;
strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
STD.Y
17-channel: 16-bit RGBW and dimmer;
strobe, color macro, auto/custom, dimmer
speed, auto speed, zoom, zoom reset
ARC.1
3-channel: RGB control
AR1.D
4-channel: RGB, dimmer
ARC.2
4-channel: RGBW
AR2.D
5-channel: RGBW, dimmer
AR2.S
6-channel: RGBW, dimmer, strobe
AR2.Z
7-channel: RGBW, dimmer, zoom, zoom
reset
HSV.
3-channel: HSV control
EDIT PR. 01–10 SC. 01–30
R.
000–255 Combines red, green, blue, and white to
generate a custom color (0–100%)
G.
B.
W.
Z.
Selects beam angle (zoom)
S. 00–20
Selects the strobe frequency
(0–20 Hz)
T. 000–255
Defines the step duration
(slow to fast)
F.
Defines the fade duration
(slow to fast)

Operation
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -11-
Menu Map (Cont.)
Main Level Programming Levels Description
SET
UPLd
****
(Enter Passcode)
Uploads custom programs to other
COLORado™ 2-Quad Zoom Tours
REST
****
(Enter Passcode)
Defaults product to factory settings
DERR
BLAC
Blacks out fixture upon loss of DMX
SAVE
Continues with last command upon loss of
DMX control
COLR
OFF
RGB set to 255 = max. output
RGBW
RGB set to 255 = balanced white
UC
Universal color balance
CURV
OFF
No dimmer
CV1
CV1(fast) to CV3 (slow) dimmer curves
CV2
CV3
DIM
OFF
No dimmer
dIM1.
Dimmer curves
dIM2.
dIM3.
dIM4.
ZOOM BASE
Sets default zoom position
(full movement)
POS.1
Sets position 1 setting for zoom limit
POS.2
Sets position 2 setting for zoom limit
CAL PASS
(Enter
Passcode) CAL
WT WH
1–11
R.
000–
255 Modifies the color macros used in the TOUR, TR16, and STD.Y personalities
G.
B.
W.
RGBW RGB.W
R.
000–
255 Defines the color temperature used when COLR is set to RGBW
G.
B.
ZOOM
POS.1
000–
255 Sets min/max position of zoom
POS.2
KEY
ON
Turns the passcode on or off
OFF

Operation
-12- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Configuration
(Standalone)
Use standalone configuration to operate the product without a DMX controller.
Auto Programs
Auto programs allow for dynamic RGBW color mixing without a DMX controller.
1. Go to the AUTO main level.
2. Select the desired auto (AT. 01–10)or custom program (PR. C1–10).
You cannot edit any of the auto programs (AT. 01–10). However, you
can edit the
custom programs (PR. C1–10). See Edit Custom Programs for details.
Edit Custom
Programs
This setting allows the programming of up to 30 scenes for each of the 10 customizable
programs, including colors and effects.
1. Go to the EDIT main level.
2. Select the desired auto program (PR. 01–10).
3. Select the desired scene (SC. 01–30).
4. Select the desired color or effect (R., G., B., W., S., Z., T., or F.).
5. Select the color or effect value (000–255 for colors and timers, or 00–20 for strobe).
6. Repeat for the other colors or effects.
7. Return to the scene (SC. 01–30) level.
8. Repeat the settings of colors and effects for the other scenes.
Master/Slave
The Master/Slave mode allows a group of COLORado™ 2-Quad Zoom Tour
s (the
slaves) to simultaneously duplicate the output of another COLORado™ 2-
Quad Zoom
Tour (the master) without a DMX controller.
1. Set each of the slaves:
a. Go to the RUN main level.
b. Select SLAV.
2. Set the master:
a. Set the running mode to DMX as explained in DMX Control.
b. Select an auto or custom program as explained in Auto Programs, or a static mix
of colors.
•The master is the one that runs a program whether in Auto, Custom or Static
Color mode.
•Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
•
The master should be the first product in the daisy chain.
Color Settings
The COLOR setting determines how the COLORado™ 2-Quad Zoom Tour generates the
white color based on various RGB settings.
1. Go to the SET main level.
2. Select COLR.
3. Select OFF, RGBW, or UC.
OFF
When all the RGB faders are set to 255, the output is maximum, although
the resulting white color may not be balanced.
RGBW
When all the RGB faders are set to 255, the resulting output is defined by
the configured White color (see White Calibration).
UC
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).

Operation
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -13-
Dimmer Curves
This setting determines how fast the output of the COLORado™ 2-Quad Zoom Tour changes
when you modify the values of the red, green, blue, white,
and dimmer faders. This setting
provides four different options to simulate the dimming curve of an incandescent lighting
product.
1. Go to the SET main level.
2. Select DIM.
3. Select a dimmer curve (OFF, dIM1., dIM2., dIM3., or dIM4.).
OFF:
The output is proportional (linear) to the dimmer and RGBW channel values.
dIM1.–4.:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, dIM1.being the fastest and dIM4.the slowest.
Curve Settings
This setting allows you to select the dimmer curve shape using the red, green, blue, white, and
dimmer faders.
1. Go to the SET main level.
2. Select CURV.
3. Select a dimmer curve (OFF, CV1, CV2, or CV3).
OFF:
The output is proportional (linear) to the dimmer and RGBW channel values.
CV1–3:
The output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, CV1 being the fastest and CV3 the slowest.
For optimum control of the 16-bit dimming channels in the TR16 and STD.Y personalities,
be sure that both dimming curves in SET > DIM and SET > CURV are set to OFF.
Control Panel
Lock
This setting enables you to activate or disable the control panel lock, which keeps non-
authorized personnel from changing the product’s settings.
1. Go to the KEY main level.
2. Select ON or OFF.
When the control panel lock is active, the product will prompt you to enter the passcode
after 30 seconds of control panel inactivity or after turning on the product.
Passcode
After being prompted to enter the passcode:
Press <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>.
Program Upload
This option allows you to copy the custom programs of one COLORado™ 2-Quad Zoom Tour
onto other COLORado™ 2-Quad Zoom Tours by using the Master/Slave mode.
1. Configure and connect the products in a Master/Slave arrangement, where the master has
the custom programs you want to transfer to the slaves.
2. From the master, go to the SET main level.
3. Select UPLD, press <ENTER>.
4. Enter the master access passcode as shown in Passcode.
5. When SEND shows, press <ENTER> to start the upload.
6. Wait for the upload process to finish (the display will show END) before continuing or
turning the products off.
The master and slaves will provide the status of the process by lighting up as follows:
•Yellow indicates that the upload process is running.
•Green indicates that the upload process completed successfully.
•Red indicates that the upload process failed due to an error. Recheck all cable
connections and restart the process. If the issue persists, contact CHAUVET®
Technical Support.
DO NOT upload the data from a COLORado™ 2-Quad Zoom Tour
to a different product.
The other product may become inoperative.

Operation
-14- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Reset
This setting allows you to reset the COLORado™ 2-Quad Zoom Tour
to the default values,
including the custom programs.
1. Go to the SET main level.
2. Select REST, press <ENTER>.
3. Enter the master access passcode as described in Passcode.
4. Wait for the reset process to finish.
Whites Setting
This setting allows you to select and edit the temperature of the white colors used in channel 6
(Macros) when in the TOUR mode, or channel 11 (Macros) when in the TR16 or STD.Y modes.
1. Go to the CAL main level.
2. When PASS shows, press <ENTER>.
3. Enter the master access passcode as described in Passcode.
4. Go to CAL.
5. Go to WT and select a white color (WH.1–11).
6. Select a color (R., G., B., or W.).
7. Select a color value (000–255).
8. Repeat for the other colors.
White Calibration
This setting allows you to select the white color shown by the COLORado™ 2-Quad Zoom Tour
when the color setting is RGBW and the DMX controller’s red, green, and blue faders are set to
255.
1. Go to the CAL main level.
2. When PASS shows, press <ENTER>.
3. Enter the master access passcode as described in Passcode.
4. Go to CAL > RGBW > RGB.W.
5. Select a color (R., G., or B.).
6. Select a color value (000–255).
7. Repeat for the other colors.
When selecting CAL > PASS > CAL> RGBW >
RGB.W, you will only be able to define the
values of R. (red), G. (green), and B. (blue).
The values of R. (red), G. (green), and B. (blue) configured from
CAL > PASS > CAL>
RGBW > RGB.W will define the color temperature shown when the RGB faders are set to
255 if SET > COLR > RGB.W is active.
Static Color
The Static Color mode allows for permanent RGBW color mixing without a DMX controller.
1. Go to the STAT main level.
2. Select the desired color (R., G., B., or W.).
3. Select the desired color value (000–255).
4. Repeat for the other colors.
5. Select Z..
6. Select the beam angle value (000–255).
7. Select S..
8. Select the desired strobe frequency (00–20).

Operation
COLORado™ 2-Quad Zoom Tour User Manual Rev. 1 -15-
TOUR Notes
These notes clarify the way the TOUR DMX personality works.
Master Dimmer
•Channel 1 controls the intensity of the currently projected color.
•When the slider is at the highest position (100%), the intensity of the output is at maximum.
Red, Green, Blue,
And White Color
Selection
•Channels 2 through 5 control the intensity ratio of each of the red, green, blue, and white
LEDs.
•When these channels are at the highest position (100%), the intensity of each color is at
maximum if SET > COLRis OFF.
•You can combine channels 2 through 5 to create over one trillion colors.
Color Macros
•Channel 6 selects the required color macro.
•Channel 6 has priority over channels 2 through 5.
•Channel 1 controls the intensity of the color macro.
Strobe
•Channel 7 controls the strobe frequency (not the intensity) of channels 2 through 6.
•Channel 7 can strobe channels 2 through 5 when not running macros, allowing the
individual faders (R, G, B, and W), as well as channel 1 (Master Dimmer), to control the
output intensity.
•Channel 7 can strobe channel 6 when running macros, allowing channel 6 to select the
macro and channel 1 to control the output intensity.
Auto/Custom
•Channel 8 selects the preset auto programs (AT.01–10) or the custom
programs (PR.C1–10).
•When activating the custom auto programs PR.C1–10, you can control the step time and
fade time using channels 2 and 3, respectively.
•Channel 8 has priority over channels 2 through 7.
•Channel 9 controls the speed at which each auto program plays.
Dimmer Speed
•Channel 10 selects the Dimmer mode and speed. Dimmer mode provides four different
options to simulate the dimming curve of an incandescent lighting product.
•When dimmer is set to values 010–029,the changes in the RGBW and master dimmer
faders are linear.
•When dimmer is set to dimming curve 1–4, Dimming Curve 1 is the fastest dimmer curve
and Dimming Curve 4 is the slowest.

Operation
-16- COLORado™ 2-Quad Zoom Tour User Manual Rev. 1
Configuration
(DMX)
Use DMX configurations to operate the product with a DMX controller.
DMX
Personalities
This setting allows you to choose a particular DMX personality.
1. Go to the PERS main level.
2. Select the desired personality (TOUR, TR16, STD.Y, ARC.1, AR1.D, ARC.2, AR2.D,
AR2.S, AR2.Z, or HSV).
•See the DMX Control Table for the highest recommended starting address you can
select for each personality.
•Make sure that the starting addresses on the various products do not overlap due to
the new personality setting.
DMX Control
In this mode, each product will respond to a unique starting address from the DMX controller. All
products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personalities.
2. Set the running mode:
a. Go to the RUN main level.
b. Select the DMX programming level.
3. Set the starting address:
a. Go to DMX main level.
b. Select the starting address (D.001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX
Personality DMX Address DMX Personality DMX Address DMX Personality DMX Address
TOUR
501
ARC.2
509
HSV
510
ARC.1
510
AR2.D
508
STD.Y
496
AR1.D
509
AR2.S
507
TR16
496
AR2.Z
506
Loss Of Signal
Setting
This setting controls how the product will respond when the DMX signal is lost.
1. Go to the SET main level.
2. Select DERR.
a. Select SAVE to make the product use the last command used when the signal is lost.
b. Select BLACto turn off the all the LEDs when the signal is lost.
Zoom Limit
Settings
These settings allow you to select the zoom range. Basic zoom (BASE) is the default setting
which allows the zoom to move at full range (000–255) and has no adjustable limit. Position 1
(POS.1) and Position 2 (POS.2) allow you to set limits on how far the zoom moves.
1. Set the zoom range to be used:
a. Go to the SET main level.
b. Select ZOOM.
c. Select BASE, POS.1, or POS.2.
2. Set the limit for zoom range POS.1 or POS.2:
a. Go to the CAL main level.
b. Enter the master access passcode as described in Passcode.
c. When CAL shows, press <UP>.
d. Go to ZOOM.
e. Select POS.1 or POS.2.
f. Select a zoom limit value (000–255).