Chauvet Intimidator Barrel LED 300 User manual

User Manual

Page 2 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
TABLE OF CONTENTS
1. Before You Begin ........................................................................................................... 3
What Is Included...........................................................................................................................3
Unpacking Instructions.................................................................................................................3
Claims................................................................................................................................................... 3
Text Conventions..........................................................................................................................3
Symbols........................................................................................................................................3
Disclaimer.....................................................................................................................................3
Product at a Glance......................................................................................................................4
Safety Notes.................................................................................................................................4
2. Introduction .................................................................................................................... 5
Product Overview .........................................................................................................................5
Product Dimensions .....................................................................................................................6
3. Setup............................................................................................................................... 7
AC Power .....................................................................................................................................7
Fuse Replacement................................................................................................................................ 7
Power Linking........................................................................................................................................ 7
Mounting.......................................................................................................................................8
Orientation............................................................................................................................................. 8
Rigging.................................................................................................................................................. 8
4. Operation ........................................................................................................................ 9
Control Panel Operation...............................................................................................................9
Menu Map.....................................................................................................................................9
Configuration (DMX).....................................................................................................................9
Starting Address.................................................................................................................................... 9
DMX Channels and Functions....................................................................................................10
11-CH Mode........................................................................................................................................ 10
Configuration (Standalone) ........................................................................................................12
Sound-Active Mode............................................................................................................................. 12
Auto Program...................................................................................................................................... 12
Master/Slave Mode ............................................................................................................................. 13
Master/Slave for Sound-Active, Auto Modes...................................................................................... 13
Service Mode...................................................................................................................................... 13
Changing Gobos.........................................................................................................................14
5. Technical Information ...................................................................................................15
Product Maintenance..................................................................................................................15
6. Technical Specifications...............................................................................................16
Returns.......................................................................................................................................17
Contact Us..................................................................................................................................17

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 3 of 17
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ Scan LED 300
•Hanging Bracket with Mounting
Hardware (preinstalled)
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Immediately upon receipt, carefully unpack the product and check the container to make
sure you have received all the parts indicated above in good condition.
Claims
If the container or the material inside the container (the product and included
accessories) appear damaged from shipping, or show signs of mishandling,
upon receipt
notify the carrier immediately, not CHAUVET®.
Failure to do so in a timely manner may
invalidate your claim with the carrier. In addition, keep the container and all the packing
material for inspection.
For other issues such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET®
within 7 days of receiving the
merchandise.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Failure
to comply could make the product not work, damage it, and harm
the user.
Important installation or configuration information. Failure to
comply with this information may prevent the product from
functioning correctly.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. CHAUVET® assumes no responsibility or liability for any errors or
omissions that may appear in this manual.
CHAUVET® reserves the right to update the
existing document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Author Date Editor Date
A. Leon 3/21/13 D. Couppe 3/22/13

Page 4 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Switchable voltage (120 V/230 V)
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Duty Cycle
x
Safety Notes
Please read the following Safety Notes carefully before working with the product. The
Notes include important safety information about installation, usage, and maintenance.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power cord by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! To prevent risk of fire or shock, do not expose
the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
•Keep this User Manual for future consultation. If you sell the product to another
user, be sure that they also receive this document.

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 5 of 17
2.INTRODUCTION
Product Overview
Rear Panel
DMX In
DMX Out
Power Out
Fuseholder
Power In
Voltage Selection Switch
(120/230 VAC)

Page 6 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
Product Dimensions

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 7 of 17
3.SETUP
AC Power
The Intimidator™ Scan LED 300 has a dual voltage power supply and it can work with
an input voltage of either 120
V, 60 Hz or 230 V, 50 Hz, depending on the position of the
voltage selection switch.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product’s back panel, or
refer to the product’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
1. Using a flat-head screwdriver, unscrew the fuse holder from the back of the product.
2. Remove the blown fuse from the holder and replace with a fuse of the exact same
type and rating.
3. Insert the fuse holder back in place, re-tighten, and reconnect power.
Power Linking
The product provides power linking via the Edison/IEC outlet located in the front/back of
the unit. Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 3 Intimidator™
Scan LED 300 units on 120 VAC or up to
7 Intimidator™ Scan LED 300 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product in other markets, you must
consult with the l
ocal CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Additional Products

Page 8 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator™ Scan LED 300 may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location for the product, always make sure there is easy
access to the product for maintenance and plenty of ventilation.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight. Please see the Technical Specifications
section of
this manual for weight information.
•When mounting the product overhead, always use a safety cable.
Mount the
product securely to a rigging point, whether an elevated platform or a truss.
•When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity.
•When power linking multiple products, you must
always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The bracket adjustment
knobs allow for directional adjustment when aiming the
product to the desired angle. Only loosen or tighten the bracket knobs manually.
Using tools could damage the knobs.
•The rubber feet also serve as floor supports. When mounting the product
on the
floor, make sure that the product
is secured so that it cannot fall over, and that
cables are away from people and vehicles.
Mounting Diagram
Hanging Bracket
Bracket
Adjustment
Knob
Rubber Foot (4)
Bracket Adjustment
Knob

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 9 of 17
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display. Please refer to the Product Overview to see the button locations
on the control
panel.
Button Function
<MODE/ESC> Press to find an operation mode or to back out of the current menu
option
<UP>
Press to scroll up the list of options or to find a higher value
<DOWN> Press to scroll down the list of options or to find a lower value
<ENTER> Press to activate a menu option or a selected value
Menu Map
Menu Programming Steps Description
DMX Mode
d001
d001–512
DMX starting address
Standalone
Mode NASL
SLAu
SoN
Standalone: Slave receive mode
NStS
SrUn
Standalone: Sound-Active
NAFA
FASt
Standalone: Auto Program
Pan Invert PAN rPAN Pan invert
Tilt Invert tit rtit Tilt invert
Display Invert diS rdiS Invert the display
DMX Personality 11CH
8CH
8-channel DMX personality
11CH
11-channel DMX personality
Reset rESt
Reset all motors to correct any errors
with motors misaligning during operation
Load Default LoAd
Revert all settings back to the factory
default
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Scan LED 300 uses up to 11 DMX channels in its 11-Channel DMX
mode, which defines the highest configurable address to 502.
If you are not familiar with the DMX protocol,
download the DMX Primer from the
CHAUVET® website.
To select the starting address, do the following:
1. Press <MODE/ESC> repeatedly until d(001–512) shows on the display.
2. Using <UP> and <DOWN>, select the starting address d(001–512).
3. Press <MODE/ESC> until one of the DMX personalities appears on the LED screen
(8CH, 11CH). The most recent DMX personality selected will appear.
4. Use <UP> and <DOWN> to change the personality.
5. Press <ENTER>.
If you are not familiar with DMX, download the DMX Primer from
www.chauvetlighting.com.

Page 10 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
DMX Channels and Functions
11-CH Mode
Channel
Value
Function
Channel
Value
Function
1
000 ó255
Pan
0–180°
7
000 ó015
016 ó127
128 ó239
240 ó255
Gobo Rotation
Stop
Rotate Counter-clockwise (slow ófast)
Rotate Clockwise (slow ófast)
Gobo bounce
2
000 ó255 Tilt 0–90°
3
000 ó006
007 ó013
014 ó020
021 ó027
028 ó034
035 ó041
042 ó048
049 ó055
056 ó063
064 ó070
071 ó077
078 ó084
085 ó091
092 ó098
099 ó105
106 ó112
113 ó119
120 ó127
128 ó191
192 ó255
Color
Open (white)
Yellow
Pink
Green
Peachblow
Blue
Kelly
Red
Dark blue
White/yellow (split colors)
Yellow/pink (split colors)
Pink/green (split colors)
Green/peach blow (split colors)
Peachblow/blue (split colors)
Blue/Kelly (split colors)
Kelly/red (split colors)
Red/dark blue (split colors)
Dark blue/white (split colors)
Rotate clockwise (slow ófast)
Rotate counter-clockwise (slow ófast)
8
000 ó003
004 ó255
Prism
Open
Stop, static prism effect
9
000 ó255
Focus
Near óFar
10
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó063
064 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó135
136 ó143
144 ó151
152 ó159
160 ó255
Function
No Function
Pan/tilt move-in-black
Pan/tilt move-in-black (disable)
Color wheel move-in-black
Color wheel move-in-black (disable)
Gobo wheel move-in-black
Gobo wheel move-in-black (disable)
Fast movement
Fast movement (disable)
All movement move-in-black (disable)
Reset pan/tilt
No Function
Reset color wheel
Reset gobo wheel
No Function
Reset prism
Reset focus
Reset all
No Function
4
000 ó003
004 ó007
008 ó215
216 ó255
Shutter
Closed
Open
Strobe (slow ófast)
Open
11
000 ó007
008 ó023
024 ó039
040 ó055
056 ó071
072 ó087
088 ó103
104 ó119
120 ó135
136 ó151
152 ó167
168 ó183
184 ó199
200 ó215
216 ó231
232 ó247
248 ó255
Movement Macros
No function
Automatic 1
Automatic 2
Automatic 3
Automatic 4
Automatic 5
Automatic 6
Automatic 7
Automatic 8
Sound 1
Sound 2
Sound 3
Sound 4
Sound 5
Sound 6
Sound 7
Sound 8
5
000 ó255
Dimmer
Dimmer: 0–100%
6
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó063
064 ó071
072 ó079
080 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó191
192 ó255
Gobo Wheel
Open
Gobo 1 (glass)
Gobo 2 (glass)
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 7 shake, fast óslow
Gobo 6 shake, fast óslow
Gobo 5 shake, fast óslow
Gobo 4 shake, fast óslow
Gobo 3 shake, fast óslow
Gobo 2 (glass) shake, (fast óslow)
Gobo 1 (glass) shake, (fast óslow)
Open
Gobo scroll: Clockwise rotation
Gobo scroll: Counter-clockwise rotation

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 11 of 17
8-CH Mode
Channel
Value
Function
1
000 ó255
Pan
0–180°
2
000
ó
255
Tilt
0–90°
3
000 ó006
007 ó013
014 ó020
021 ó027
028 ó034
035 ó041
042 ó048
049 ó055
056 ó063
064 ó070
071 ó077
078 ó084
085 ó091
092 ó098
099 ó105
106 ó112
113 ó119
120 ó127
128 ó191
192 ó255
Color
Open (white)
Yellow
Pink
Green
Peachblow
Blue
Kelly
Red
Dark blue
White/yellow (split colors)
Yellow/pink (split colors)
Pink/green (split colors)
Green/peach blow (split colors)
Peachblow/blue (split colors)
Blue/Kelly (split colors)
Kelly/red (split colors)
Red/dark blue (split colors)
Dark blue/white (split colors)
Rotate clockwise (slow ófast)
Rotate counter-clockwise
(slow
ó
fast)
4
000 ó003
004 ó007
008 ó215
216 ó255
Shutter
Closed
Open
Strobe (slow ófast)
Open
Channel
Value
Function
5
000 ó007
008 ó015
016 ó023
024 ó031
032 ó039
040 ó047
048 ó055
056 ó063
064 ó071
072 ó079
080 ó087
088 ó095
096 ó103
104 ó111
112 ó119
120 ó127
128 ó191
192 ó255
Gobo Wheel
Open
Gobo 1 (glass)
Gobo 2 (glass)
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 7 shake, fast óslow
Gobo 6 shake, fast óslow
Gobo 5 shake, fast óslow
Gobo 4 shake, fast óslow
Gobo 3 shake, fast óslow
Gobo 2 (glass) shake, (fast óslow)
Gobo 1 (glass) shake, (fast óslow)
Open
Gobo scroll: Clockwise rotation
Gobo scroll: Counter-clockwise rotation
6
000 ó015
016 ó127
128 ó239
240 ó255
Gobo Rotation
Stop
Rotate Counter-clockwise (slow ófast)
Rotate Clockwise (slow ófast)
Gobo bounce
7
000 ó003
004
ó
255
Prism
Open
Stop, static prism effect
8
000 ó255
Focus
Near óFar

Page 12 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
Configuration
(Standalone)
Set the product in one of the standalone modes to control without a DMX controller.
1. Connect the product to a suitable power outlet.
2. Turn the product on.
Never connect a product that is operating in any standalone mode (either Static,
Automatic, or Sound) to a DMX string connected to a DMX controller. Product
s in
standalone mode may transmit DMX signals that could interfere with the DMX
signals from the controller.
Sound-Active
Mode
To enable the Sound-Active mode:
1. Press <MODE/ESC> repeatedly until one of the Standalone modes shows on the
display (SLAu, NStS, NAFA, NASL).
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select <NStS>.
4. Press <ENTER>. <SrUn>will appear on the display.
The product will only respond to low frequencies of music (bass and drums).
Auto Program
To enable the Auto program:
1. Press <MODE/ESC> repeatedly until one of the Standalone modes shows on the
display (SLAu, NStS, NAFA, NASL).
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select <NAFA>.
4. Press <ENTER>. <FASt>will appear on the display.

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 13 of 17
Master/Slave
Mode
The Master/Slave mode allows a single Intimidator™ Scan LED 300 unit (the “master”)
to control the actions of one or more Intimidator™ Scan LED 300
units (the “slaves”)
without the need of a DMX controller. The master unit will be set to operate in either
Auto program or Sound-
Active mode, while the slave units will be set to operate in Slave
mode. Once set and connected, the
slave units will operate in unison with the master
unit.
Configure the units as indicated below.
Slave units:
1. Press <MODE/ESC> repeatedly until SLAu shows on the display.
2. Press <ENTER> to accept.
3. Set the DMX address to d001.
4. Connect the DMX input of the first slave unit to the DMX output of the master unit.
5. Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
6. Finish setting and connecting all the slave units.
Master unit:
1. Set the master unit to operate in either Auto program or Sound-Active mode.
2. Make the master unit the first unit in the DMX daisy chain.
Configure all the slave units before connecting the master unit to the DMX daisy
chain.
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because the controller
may interfere with the signals from the master
unit.
Do not connect more than 31 slave units to the master unit.
Master/Slave for
Sound-Active,
Auto Modes
Master/Slave may also be used to synchronize a maximum of 31 slave units to a single
master set to any of the standalone modes:
Set the master product in any of the Standalone modes: Sound-Active mode or Auto
programs.
To set the slave products:
1. Press <MODE/ESC> until NASL appears on the LED screen.
2. Using <UP> and <DOWN> select <SLAu>.
3. Press < ENTER >. <SoN> will appear on the screen.
Service Mode
The Intimidator™ Scan 300 has an imbedded menu that requires a passcode for use.
The purpose of
this menu is to electronically adjust the home positions of various
features. To access this menu:
1. Press < MODE/ESC > and hold for at least 10 seconds.
2. Using <UP>and <DOWN>, enter the following pass code: “2323”. Press <UP> to
change the blinking digit in ascending order, and press <DOWN> to move on to the
next digit.
3. Press <ENTER>.
Menu Option
Selection
Instruction
P128
000–255
Adjustment for pan
t128
000–255
Adjustment for tilt
G128
000–255
Adjustment for the gobo wheel
r128
000–255
Adjustment for the gobo wheel rotation
C128
000–255
Adjustment for the color wheel
F128
000–255
Adjustment for the focus
Note: This mode will automatically terminate after 10 seconds of being idle.

Page 14 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
Changing
Gobos
To change the gobos in the Intimidator™ Scan 300, you do not need to remove the gobo
wheel. Simply:
1. Turn off and disconnect fixture from power outlet.
2. Place the product on a flat, level surface with the front facing up.
3. Open the head cover by loosening the ten fastening screws at the sides of the top
cover.
4. Remove the four screws on the cover plate underneath the display to access the
gobo wheel.
5. Rotate the gobo wheel until the gobo that needs replacing is accessible.
6. Separate the gobo holder away from the gobo wheel by pushing it forward, toward
the mirror/LED. Be careful not to push the gobo out of the gobo plate.
7. Extract the gobo holder by pulling it outward (straight up). (See the #1 & 2 arrows
on diagram.)
8. On a flat surface, remove the expansion ring that holds the gobo in place and
remove the gobo from the gobo plate.
9. Insert a new gobo and hold it in place with the expansion ring.
10. To re-insert the new gobos, slide the tip of the gobo holder under the pressure plate
near the center of the gobo wheel.
11. Push the gobo holder inwards. DO NOT force the gobo holder into the gobo wheel
slot. If correctly installed, the gobo holder should accommodate itself in the gobo
wheel slot.
12. Replace covers.
Gobo Replacement Diagram
Gobo Wheel Detail Views
Expansion Ring
Gobo
Gobo Holder

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 15 of 17
5.TECHNICAL INFORMATION
Product
Maintenance
Dust build-up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and mechanical wear. To maintain optimum
performance and minimize wear, clean the product at least twice a month. U
se and
environmental conditions could cause increased cleaning frequency.
To clean the product, follow the instructions below:
•Unplug the product from power.
•Wait until the product is cold.
•Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external surface/vents.
•Clean all external optics and glass surfaces with a mild soap solution, ammonia-free
glass cleaner, or isopropyl alcohol.
•Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
•Softly wipe any dirt or grime to the outside edges of the external optics and glass
surfaces.
•Gently polish these surfaces until they are free of haze and lint.
•Keep contact with the mirror’s
surface to a minimum to avoid scratching or damaging
it.
Always dry surfaces carefully after cleaning.
Do not spin the cooling fan/fans using compressed air because you could damage
it/them.

Page 16 of 17 Intimidator Scan™ LED 300 User Manual Rev. 6
6.TECHNICAL SPECIFICATIONS
Dimensions and
Weight
Length
Width
Height
Weight
11 in (279 mm)
10 in (254 mm)
18.9 in (478 mm)
14.7 lbs (6.7 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Switchable
120/230 V, 50/60 Hz
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
236 W
237 W
Operating current
2 A
1 A
Power linking units
3 units
7 units
Fuse
F 2 A, 250 V
F 2 A, 250 V
Power I/O
US/Worldwide
UK/Europe
Power input connector
Neutrik® powerCON® A/IEC
Neutrik® powerCON® A/IEC
Power output connector
Neutrik® powerCON®
B/Edison
Neutrik® powerCON® B/IEC
Power Cord plug
Edison (U.S.)
Local plug
Light Source
Type
Power
Lifespan
LED
60 W
50,000 hours
Color
Quantity
Current
White
1
14.9 A
Gobos
Type
Quantity
Gobo Dimensions
Metal
5
23.8 mm circumference
Glass
2
20.9 mm image
2 mm max thickness
Photo Optic
Parameter
Illuminance @ 2 m
2,850 lx
Beam angle
21º
Strobe Rate
0–20 Hz
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Fan
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
8, 11
Ordering
Product Name
Item Code
UPC
Intimidator™ Scan LED 300
08020175
781462205591

Intimidator™ Scan LED 300 User Manual Rev. 6 Page 17 of 17
In case you need to return a product or request support, follow the procedure below:
•If you live in the U.S., contact CHAUVET® World Headquarters (see below).
•If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below).
•If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your
distributor of record. See www.chauvetlighting.com for distributors outside the U.S.,
United Kingdom, or Ireland.
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of
record and follow their instructions on how to return CHAUVET® product
s to
them. Visit our website for contact details.
Returns
Call the corresponding CHAUVET® Tech Support office and request a Return
Merchandise Authorization (RMA) number before shipping the product
. Be prepared to
provide the model number, serial number, and a brief description of the cause for the
return.
You must send the merchandise prepaid
, in its original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Clearly label the package with the RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Write the RMA number on a properly affixed label. DO NOT write the RMA number
directly on the box.
Before sending the product, clearly write the following information on a piece of paper
and place it inside the box:
•Your name
•Your address
•Your phone number
•The RMA number
•A brief description of the problem
Be sure to pack the product
properly. Any shipping damage resulting from inadequate
packaging will be your responsibility. As a suggestion, proper UPS packing or double-
boxing is always a safe method to use.
CHAUVET®
reserves the right to use its own discretion to repair or replace
returned product(s).
Contact Us
World Headquarters
CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
United Kingdom & Ireland
CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: t[email protected]om
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.com
World Wide Web
www.chauvetlighting.co.uk